512484
73
Verklein
Vergroot
Pagina terug
1/268
Pagina verder
EN
19
Figure 1.16 -
Strip 6mm of insulation
from the wire end
Figure 1.15 -
Two loose wire ends
at the starting point
Figure 1.17 -
Tighten the screw to secure the
perimeter wire into the connector
1.4.4 Completing the Perimeter Wire Setup
Once the perimeter wire is completed and pegged to the ground, the last step to complete is
attaching the perimeter wire ends to the Base Station board and testing the setup.
There are two loose wire ends where the perimeter wire set up was started (Figure 1.15).
Use the same peg to fasten these two perimeter wire ends down to the ground and twist them.
Cut the wire end without the connector so they are of equal length - removing any excess wire.
Strip back 6 mm of insulation from the wire end (Figure 1.16).
Insert the free perimeter wire into hole of connector using a small flat screwdriver; tighten the
screw to secure the perimeter wire into the connector (Figure 1.17).
1.4.5 Placing and Connecting the Base Station
Connect the Perimeter Wire connector to the Base
Station board (Figure 1.18).
Before securing the Power Supply cord to the Base
Station, carefully lay the length of the cord out,
beginning from the Base Station and leading to the
main power supply and insure it is fastened securely to
the ground and does not present a tripping hazard.
Do not cross it over surfaces where it cannot be
fastened, such as sidewalks or driveways. For ultimate
protection, consider an underground placement within a
protective conduit.
Connect the Power Supply cord to the Base Station
board. See Figure 1.19.
Route the Power Supply cord into the Base Station
cover as shown in Figure 1.20.
Close the cover of the Base Station; confirm it is locked
well in its place (Figure 1.21).
Figure 1.20 -
Routing the Power Supply
cord out of the cover
Figure 1.21 -
Closing the Base Station cover
Figure 1.18 -
Perimeter Wire connection
to the Base Station
Figure 1.19 -
Power Supply cord connection
73

Hulp nodig? Stel uw vraag in het forum

Spelregels
1

Forum

Robomow-Tuscania-500

Zoeken resetten

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Robomow Tuscania 500 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Robomow Tuscania 500 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans als bijlage per email.

De handleiding is 9,61 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info