724736
5
Verklein
Vergroot
Pagina terug
1/64
Pagina verder
Robotic Mower
RX50 Pro S, RX50u Connect
RX20 Pro, RX20u, RX12u
EN
User Guide
See how
to install
Original Operating Instructions
1/Learn
Your Lawn
I’m
Robomow.
Nice to
meet you.
Your safety is important to us -
Please review this Manual carefully for all safety warnings and
take extra caution to keep both children and pets off the lawn
when Robomow is in operation.
Safety first ...................
2
Installation .................
15
Quick reference ............
35
2 3
Safety first
IMPORTANT!
READ CAREFULLY BEFORE USE
KEEP FOR FUTURE REFERENCE
Warning decal definitions
Safety warnings & precautions
Safety features
Do not allow children to use or operate the mower.
Children must be supervised at all times.
Warning
decal definitions
2 3
This symbol indicates that the mains electricity is double
insulated.
This symbol indicates that the product is designed for
indoor use only.
1 2 3 4 5 6 7
1. This is a dangerous power tool. Exercise care when operating
and follow all safety instructions and warnings.
2. Read the Safety Manual carefully before operating your mower.
3. Be careful of thrown objects during operation.
4. Keep a safe distance from the mower while it is operating. Keep
people, especially children, pets and bystanders away from the
area where the mower is operating.
5. CAUTION - Do not touch rotating blade. Keep hands and feet
away and do not lift the mower from the ground.
6. Remove the disabling device before working on or lifting the
mower (see Section 3.b).
7. Do not ride the mower.
Do not dispose of the mower or any of its parts as unsorted
municipal waste. It should be collected separately.
This product conforms to applicable EU directives.
4 5
A. Before you begin
1. Read this Safety Manual carefully before operating the
mower to become familiar with its controls and proper
use.
2. Never allow children, persons with reduced physical,
sensory or mental capabilities or lack of experience and
knowledge or people unfamiliar with these instructions
to use the machine. Local regulations may restrict the
age of the operator.
3. You are responsible for accidents or for harm to
other people or their property.
4. It is your responsibility to inform your neighbors about
the risks, and that it is forbidden to enter your lawn while
the mower is operating.
5. If your lawn is open to the street and/or your neighbors,
you must be present during the mower’s operation to
prevent others from accessing your lawn. Alternatively,
you must protect / fence your lawn so that others will
not be able to access the mower during operation.
Safety warnings &
precautions
4 5
B. Preparations
1. Ensure the correct installation of the Perimeter Wire, as
instructed.
2. Inspect periodically the area where the mower is used
and remove all stones, sticks, cones, wires and other
foreign objects.
3. Periodically visually inspect to verify that the blade is not
worn or damaged. Replace a worn or damaged blade
(Part No. MRK9100A/MRK9100W). Switch the mower off
when inspecting or replacing the blade.
C. Operation
IMPORTANT SAFETY WARNING!
Do not leave the mower to operate unattended if
you know that there are pets, children or people
in the vicinity. Never mow while people (especially
children) or pets are nearby.
1. Do not operate the mower if any safety feature or any
part is damaged, worn or inoperable.
2. Keep hands and feet away from the cutting blade and
other moving parts.
3. Always switch the mower off before lifting it or planning
to operate any adjustments.
4. Never pick up or carry the mower while the motors are
running.
6 7
5. Do not touch the blade before it has completely stopped
rotating.
6. Do not use the mower for any purpose other than cutting
lawn.
7. Keep all guards, shields, safety devices, and sensors
in place. Repair or replace damaged parts, including
decals.
8. Set the weekly program at times when there are no
people on the grass.
9. Do not connect a damaged power cord to the supply, or
touch a damaged cord before it is disconnected from the
supply as it can lead to contact with live parts.
10. Keep the extension power cord away from the blade to
prevent the mower from damaging it. A damaged power
cord can lead to contact with live parts.
11. If the power cord becomes damaged or entangled during
use, detach it from the mains by pulling the plug from
the socket.
12. In the event of accident or breakdown whilst the mower
is operating, immediately press the red STOP button.
6 7
D. Transportation
Within the working area:
1. Press the STOP button to stop the
mower.
2. Switch the mower off, and carry it by its
carrying handle as shown in the picture
to the right.
Over long distances:
When transporting your mower over long
distances, make sure it is switched off.
IMPORTANT! It is recommended to keep the original
packaging for shipping purposes.
8 9
E. Using the remote control (manual mowing)
1. Mow only in daylight or in good artificial light, and avoid
operating on wet grass.
2. Do not operate the mower barefoot or wearing open
sandals. Always wear substantial footwear and long
trousers; always make sure of your footing on slopes.
3. Use extreme caution when reversing the direction of the
mower towards you.
4. Always switch on the motor according to the instructions
while standing away from the blade.
5. Do not mow manually in slopes greater than 15 degrees
or where a firm footing is not possible.
F. Batteries
1. Do not open or damage the battery pack.
2. The Battery Pack contains electrolytes. In case of an
electrolyte leakage from the Battery Pack, the following
actions should be taken:
Skin contact: Wash the contact areas off immediately
with water and soap.
Eye contact: Flush the eyes with plenty of clean water
for at least 15 minutes immediately, without rubbing.
Get medical assistance.
3. Ensure that the battery is charged using the correct
charger recommended by the manufacturer. Incorrect
use may result in electric shock, overheating or leakage
of corrosive liquid from the battery.
8 9
G. Maintenance and special instructions
1. Always switch the mower off and remove the Disabling
Device before clearing blockage/checking/cleaning/
working on it, or after striking a foreign object to inspect
the machine for damage. Never attempt to service or
adjust the mower while it is in operation.
2. In case of abnormal vibrations, stop the mower, switch it
off and check for any damage of the blade. Replace a worn
or damaged blade (Part No. MRK9100A/MRK9100W)
to preserve balance. If the vibration continues, call for
service.
3. Use heavy gloves when inspecting or servicing the blade.
4. Do not perform maintenance barefoot or wearing open
sandals. Always wear suitable work shoes and long
trousers.
5. Replace worn or damaged parts for your safety.
6. Use only original equipment and accessories. It is not
permitted to modify the original design of the mower. All
modifications are made at your own risk.
7. Ensure that only replacement cutting means of the
right type (Part No. MRK9100A/MRK9100W) are used.
8. Maintenance/servicing/cleaning of the mower should be
according to manufacturer’s instructions.
9. Keep all nuts, bolts and screws tight to be sure the
machine is in safe working condition.
10 11
WARNING!
When there is a risk of a lightning storm, disconnect
the Perimeter Wire from the Base Station and the
Power Supply 230 V/120 V plug from the power outlet.
H. Product end of use
1. The mower and its accessories should be collected
separately at the end of their life to prevent waste
electrical and electronic equipment from ending up in
landfill sites, and to protect and improve the quality of
the environment.
2. Do not dispose of the mower or any other of its parts
(including the Power Supply and Base Station) as unsorted
municipal waste – they should be collected separately.
3. Ask your local distributor/dealer about return and
collection systems availability.
4. Do not dispose of the battery pack in a fire, and do not
place used batteries in your household trash.
5. The battery must be collected, recycled, or disposed of in
an environmentally sound manner.
10 11
WARNING!
Your mower is equipped with numerous built-in
safety features. However, the mower is a hazardous
device with a sharp blade, which can cause major
injury to anyone who comes in contact with it.
Therefore, it is absolutely forbidden to be on the
lawn while the mower is working. Alternatively,
halt the mower’s operation when people (especially
children) or pets are to stay or play on the lawn.
A. Child Lock
The Child Lock prevents unintended operation of
the mower by an accidental press of one of the
buttons. Only pressing two buttons in the right
order will initiate the operation. It is required to
activate the Child Lock feature if children under age 6
may come in contact with the mower.
B. Disabling Device
The Disabling Device will prevent anyone from operating
the mower. when it is removed. It is highly recommended
to remove the Disabling Device to prevent operation of
the mower by children or people who are unfamiliar with
the mower. or are not allowed to use it.
Safety
features
12 13
C. Lift Sensor
If the mower is raised from the ground during the blade’s
operation, the blade will stop rotating immediately.
D. Tilt Sensor
If the mower is tilted up towards a vertical position, the
blade will stop immediately.
E. Obstruction Sensor
Your mower detects interfering obstacles in its way during
operation. When the mower collides with an obstacle, it
will stop the rotation of the blade immediately, will stop
movement in that direction and reverse itself away from
the obstacle.
F. Emergency Stop Button
Pressing the STOP button at any time during operation
will stop the mower and the blade immediately.
G. GO/ON-OFF button
The GO/ON-OFF button allows to completely power off
your mower. Switching the mower off will prevent it from
any operation. It is required to switch the mower off
before lifting it and before any maintenance operation.
12 13
H. Base Station and Perimeter Wire
Your mower cannot operate without a Perimeter Wire
installed and activated through the Base Station. In the
event the Perimeter Wire signal is turned off, the mower
will stop operating.
I. Anti-Theft (not applicable to models for
lawns under 200 m
2
)
The theft protection function will prevent anyone from
using or driving the mower unless they unlock it by
connecting to it with a registered mobile device.
14 15
Let’s get
started.
Can’t wait
to mow your
lawn.
14 15
Installation
Congratulations on purchasing your new mower!
Your new mower will move randomly within its working area, as
defined by the Perimeter Wire. This kind of random movement
provides the perfect cut and ensures complete coverage of your lawn.
At the end of each mowing ride, your mower will follow the Perimeter
Wire and automatically return to the Base Station for charging.
After a quick and simple installation, you will be ready to enjoy your
free time while your new friend looks after your lawn.
16 17
So where are we heading?
Get started
Choose Base Station location
Lay the wire
Wire your lawn
Power up
Connect Everything
GO!
Your mower is ready
Set base
Install the Base Station
Correct installation of your mower will ensure maximum results. This
is what it takes to prepare it to do a perfect job for you.
16 17
This is what you find in the
box
Power Supply
With 10 m / 33 ft extension cable
Base Station
This is where the mower recharges
Perimeter Wire with a plot connector*
Marks the working area for your mower
(*) Not provided with Pro/XR1 models
Wire Pegs*
For securing the wire to the ground
(*) Not provided with Pro/XR1 models
Base Station Head
Generates Perimeter Wire signal
The product
Your new Robotic Mower
RoboTool
For blades replacement and
servicing. IMPORTANT! Keep this
tool for future use.
18 19
Ready? Let’s begin...
Plot Connectors
For connecting the Perimeter Wire
to the Base Station
Wire Connectors
For splicing the Perimeter Wire in
case of a cut
RoboRuler
For measuring the Perimeter Wire’s
distance from the lawn’s edge
Base Station Stakes (x4)
For affixing the Base Station to
the ground
User Guide
USER
GUIDE
18 19
The Base Station is where your mower recharges, and where the
Perimeter Wire starts and ends.
Follow these simple guidelines to find a proper location for
your Base Station
Get started
Up to 10 meters / 33 feet
away from a power outlet
A min. of 1 meter / 3.3 feet
straight wire before, after and
aside the base to allow smooth
docking
Even and flat (up to
+/-5% slope)
Rule #1:
Rule #2:
Rule #3:
Choosing the Base Station location
1
meter
1
meter
1
meter
Base Station
Max 10 m / 33 ft
20 21
** See additional installation options in Appendix A **
TIP
The Base Station will be installed at a later stage, after the
Perimeter Wire is in place.
Watch the proper
direction of the Base
Station relative to the
lawn’s edge
Min 1 m / 3.3 ft
Rule #4:
A minimum of 1 meter / 3.3
feet from a sprinkler head
to avoid hitting the mower
directly and damaging its
internal components
20 21
Lay the Perimeter Wire (“virtual boundary”), which defines
the working area for the mower.
Lay the
wire
Combination pliers
Have mower’s package nearby.
Before you start wiring, use your old mower to cut your grass
to the height no more than 6 cm (2.5”) one last time. This
will make inserting pegs easier and help ensure the mower
doesn’t cut the wire.
TIPS
A. Get to know wire distances
WHAT
YOU’LL
NEED
Cutter
Use the RoboRuler to determine a distance, which you should keep
between the Perimeter Wire and the lawn’s edge.
Hammer
22 23
If the edge is relatively flat, lay the
wire at RoboRuler distance II from
it.
If the edge is a drop or if the
ground is sandy/soft, use distance
III of the RoboRuler.
When the edge is a wall or a
bush, use distance IV of the
RoboRuler.
Keep a minimum of 1.2 m (4 ft)
if the edge of the lawn borders
water.
III
Min 1.2m (4ft)
II
> 5cm (2in)
IV
22 23
Pull out the wire end marked “A” from the
Perimeter Wire spool
Leave a tail of approx. 20 cm / 8”
Once a tail is made, secure it to the ground where you intend to install
your Base Station. Measure the correct RoboRuler distance from the
edge:
B. Make a good start
20cm
24 25
TIP
Well done! This was the most complex part
of the wire installation. Let’s move on…
SLOPES
Slopes along the edge
To ensure your mower doesn’t slip off the lawn, especially
when the grass is wet, the Perimeter Wire must exclude a
slope along the edge of your lawn with an incline of over 10% -
that is, 10 cm rise per 1 m [4 in rise per 3 ft].
Slopes within the lawn
Your mower can mow areas
within the lawn with a slope
of up to 15% [15 cm rise per 1
m/0.5 ft rise per 3 ft].
Max 15%
Less than 10% More than 10%
24 25
The Perimeter Wire is secured to the ground by the pegs supplied
with the product.
Pull the wire tight while
hammering the pegs to
their final depth in the
ground.
Take care not to damage
irrigation pipes.
Place the pegs every few tens of
centimeters.
Add pegs where necessary to keep
the wire tight to the ground to
avoid damaging it by the mower.
C. Keep laying the wire
Lay the Perimeter Wire loosely along the perimeter as you walk along
the lawn’s edge.
Start unwinding the wire counter clockwise around the lawn
starting at the Base Station’s location.
~0.5m
26 27
D. Protect obstacles
Hard obstacles
Obstacles that are vertical, rigid and higher than 15 cm (6 in), such as
trees or telephone poles, do not need to be protected by the Perimeter
Wire. The mower will bump into them and turn away.
Set the Perimeter Wire CLOCKWISE around the obstacle,
otherwise the mower will drive into the Perimeter Island or
won’t be able to mow the area around it properly.
TIP
Tree roots, which stick out more than
2 cm above the ground, should be
protected by a perimeter island.
Soft obstacles
Objects such as flower beds,
ponds, or small trees must
be protected by setting
Perimeter Islands.
OR
If your lawn has additional
areas as shown below, see
Appendix B.
26 27
E. What if you have secondary areas?
F. Complete wire setup
Arrive back to the base location until the two wire ends meet each other
Put the last peg very close to the first one
Make both wire end the same length. Use a cutter to cut off the remaining
wire.
28 29
Do not leave or create wire wraps
1 2
Put one of the provided plot connectors on the second wire end
Use pliers to press the connector and a cutter to cut off the
remaining wire
28 29
Set base
3
Place the Base Station in its planned location
Properly align the center of the Base Station with the Perimeter Wire
Fix the base to the ground with the 4 supplied metal stakes
Be careful not to damage irrigtion pipes when hammering
down the stakes.
30 31
Power
up
1. Connect the wire tail marked A to the A terminal and the other tail to
the B terminal of the Base Station head.
2. Connect the power supply connector to the Base Station head as well.
3. Note the markings for placing the Base Station Head.
Markings for placing the Base Station Head
30 31
4. Place the head on the Base Station and align it with the markings as
shown in the picture below.
5. Slide the head all the way through.
Pay attention to the sliders and a dedicated slot for threading the wires.
Slide
32 33
6. Plug in the power supply into a socket.
Take the power cord out of the mowing area (to prevent the
mower from damaging it) and secure the cord firmly to the
ground (so that it does not become a tripping hazard).
TIP
If for some reason you need to remove the base station head,
you can do so by lifting the lever (A) and pushing it towards the
inside of the base.
Lift
Push
32 33
GO!
Your mower is ready!
Place your mower in the center of your lawn
Press GO for 2 seconds to switch it on
Now press the STOP /
once to send the mower to the Base Station.
The mower will start driving towards the edge of the lawn to locate
the Perimeter Wire. Once on it, the mower will follow the wire to
reach the Base Station and park there for charging.
Operating your mower is super easy! For basic commands and
troubleshooting, please refer to the “Quick Reference” part
.
2 sec
34 35
Well Done!
Now relax, and let your
mower do the work.
34 35
Quick reference
Knowing your mower
Single-button operation
Additional options with the mobile app
Taking care of your mower
Troubleshooting
FAQs
36 37
In order to fully enjoy your mower, learn about its different parts and
messages. Understanding how it works and interacts will lead to smooth
and easy operation.
Knowing your
mower
Front side
Floating deck
Carrying handle with
a touch sensor
Front drive wheel
Rear side
Mowing height
adjustment knob
Operating panel
Disabling device
Charging Contacts
Rear glider
36 37
Bottom view
Floating
mowing deck
Rugged drive
wheels
Mowing
blade
Glider
surface
38 39
Operating panel
STOP / Home
button
Lock indication:
Steady orange: child
protection is active
Blinking orange: theft
protection is active
ON-OFF indication:
Steady green: mower is
switched on / mower is in
operation
Blinking green: mower is
returning to the Base Station /
mower is driving to a starting
point
Blinking green fast (and
beeping): mower is departing
from Base Station
Blinking green slow: mower is
asleep
Blinking red / steady red:
mower is at fault (see
troubleshooting section)
GO / ON-OFF
switch
Battery indication:
Blinking green: mower is
charging in the base
Steady green: the battery is
fully charged
Blinking red: the battery is
almost empty, recharging
will soon be required
Steady red: the battery is low
and needs to be recharged to
resume operation
Green
Orange
Orange
Green
Green
Red
Red
Green
Green
Green
Red
38 39
Charging pins
Base Station head
Rear slot and opening
for head’s removal
Base Station Indication:
Steady green: perimeter wire signal is OK; the mower
is inside the base
Blinking green: perimeter wire signal is OK; the
mower is outside the base
Blinking red fast: perimeter wire is damaged or
disconnected
Blinking red slow: poor perimeter wire connection or
the wire is too long
Steady red: faulty power supply
Green
Green
Red
Red
Red
Base Station
40 41
Before anything else
Single-button
operation
Set the mowing height to the desired level. We recommend setting
the mowing height to the maximum during the first mowing
operation or at the beginning of a season, and then gradually
reducing it to the desired level.
To set the mowing height, push and turn
the mowing height adjustment knob to the
desired direction:
I means the lowest mowing height (15 mm
/ 0.6”)
IIII means the highest mowing height (45
mm / 1.8”)
push & turn
TIP
Your mower is designed for frequent cutting at a desired
height
Before the first use, make sure your grass is cut not higher
than 60 mm (2.5”)
IMPORTANT SAFETY WARNING!
Do not leave the mower to operate unattended if you
know that there are pets, children or people in the vicinity.
Never mow while people (especially children) or pets are
nearby.
40 41
2 seconds
Powering up
To power up your mower, press and hold the GO button for 2 seconds
until the ON/OFF indication is lit.
When you need to switch it off, simply press and hold GO button for 2
seconds, until the ON/OFF indication goes off.
Note: If the theft protection is enabled(not
applicable to models for lawns under 200 m
2
/
2150 ft
2
), you will need to unlock your mower via
the mobile app before you can switch it off.
WARNING
Clean the lawn from stones, fallen branches or other foreign
objects before using the mower. The limited warranty of your
mower does not cover damages caused by objects left in the
lawn.
42 43
Enabling child protection
Child protection prevents accidental use of the mower by little
children. When child protection is enabled, the mower will require a
special combination to start a mowing operation or to go back to its
base.
To enable child protection, press and hold the
GO + STOP buttons together for 6 seconds.
If you wish to disable child protection, press
and hold the GO + STOP buttons together for 6
seconds again.
Alternatively, child protection can be enabled
or disabled conveniently via the mobile app (not
applicable to models for lawns under 200 m
2
/
2150 ft
2
).
6 seconds
42 43
Starting a mowing operation
Starting a mowing operation is super easy!
If you wish to start a regular
mowing operation, all you need to
do is to press the GO button once.
If the regular mowing duration
(depends on a particular model of
your mower) is too long for your
lawn, you can initiate half-time
mowing operation by pressing the
GO button twice.
When child protection is enabled,
a special combination of keys
is required to start a mowing
operation. Hold down the STOP
button and press the GO button
once to unlock the child protection
for 30 seconds. The Lock indication
will be temporarily switched off.
Now you can start a mowing
operation as described above. As
soon as the mowing operation is
started, the child protection will
automatically relock itself.
X 1
X 2
X 1
44 45
Stopping an operation
To stop any current operation, press the STOP / button.
Sending the mower to its base
To send the mower to its base, simply press the STOP / button
when the mower is inside the lawn.
If child protection is enabled, see the “Starting mowing operation”
section above to temporarily unlock it. Then press STOP /
button
to send the mower to its base. The child protection will relock
automatically.
Automatic charging
Once a mowing operation is finished, your mower automatically
returns to its base station for charging to be ready for the next
operation.
44 45
How much mowing does your lawn need?
The amount of mowing depends on a season and on the size of your
lawn. We recommend the following amounts of weekly mowing times
per lawn size in peak season.
Lawn size * Recommended weekly mowing times
Up to 50 m
2
2 hours
51 - 100 m
2
4 hours
101 - 150 m
2
6 hours
151 - 200
m
2
9 hours
201 - 300 m
2
14 hours
301 - 400 m
2
18 hours
more than 400 m
2
21 hours
(*) Check the recommended lawn size in your mower's specifications
For the best look of your lawn, we recommend spreading
the mowing times evenly among as many days in a week as
possible.
TIPS
46 47
Along with a totally exciting experience, it brings additional
options and capabilities to your small and clever mower:
Setting automatic mowing schedule
Activating theft protection
Defining additional starting points
Remote controlling with manual mowing
Remote diagnostics by a service station
Avoiding interference by changing signal type
Enabling "Energy Saver" mode to minimize power
consumption to comply with CEC/DoE regulation.
Additional options
with the mobile app
(not applicable to models for lawns under
200 m
2
/ 2150 ft
2
)
Your mower is a smart connected product. It comes with a
built-in Bluetooth LE (Low Energy) device that enables you to
control your mower from your smartphone.
A free complementary mobile app will allow you to experience
your mower in a whole different way!
You can download the app from Google Play Store (Android) or
from Apple AppStore (iOS).
46 47
Taking care of your
mower
Once a month:
Inspect the underside of the mower. Clean if necessary. Carefully
scrape the collected grass debris (using a small stick or similar
object) from under the mowing deck.
Check the Perimeter Wire and add pegs where it is loose and not
tight to the ground. In case of seasonal changes in the lawn, make
sure to adjust the wire accordingly.
Inspect the Base Station, clean it from mud and debris to allow
proper docking.
Periodic maintenance
To allow better maintenance and to keep your mower in good
condition, it is recommended to take it to a certified dealer
for service prior to winter storage.
WARNING
Severe injury and damage hazard!
Always switch the mower off before lifting it. The blade is very
sharp. It can cause severe cuts or lacerations. Always wear heavy
work gloves when working with or around the blade. NEVER use a
damaged or broken blade. NEVER sharpen the blade.
IMPORTANT!
NEVER use high pressure water to clean the mower.
Liquids can damage components. Use only an air
blower or wet cloth to wipe the surface clean.
48 49
Operating the Disabling Device
The Disabling Device prevents the operation of your mower when it is
removed.
If the Disabling Device is pulled out, the current operation will be
immediately halted, the Lock indication will blink three times and the
ON/OFF LED will switch off.
If any button on mower’s operating panel is pressed, the Lock indication
will blink three times to indicate that the Disabling Device is missing.
If theft protection is enabled, it will remain active even though the
Disabling Device is removed.
Replacing the blade
1. Power the mower off by pressing GO button for 2 seconds.
48 49
2. Remove the Disabling Device.
3. Put on heavy-duty gloves, and place RoboTool over the blade so that
it covers the whole blade.
4. Use the provided Allen tool (comes with a replacing blade) to unscrew
the screws while holding the blade with the RoboTool.
5. Replace the blade with a new one (Part No.MRK9100A/MRK9100W).
6. Make sure to close both screws tightly.
Lift
Pull
50 51
Winter storage
The mower
Fully charge the mower in its base
Switch the mower off by pressing the GO button for 2 seconds
Store the mower in dry indoor conditions at ambient temperatures
above 0°C.
Base Station
No winter storage is required for a Base Station. It can be left on the
lawn during the winter period.
It is recommended to disconnect the Power Supply from the mains
during the winter storage period.
Winter service
To allow better maintenance and to keep your mower in good condition,
it is recommended to bring it to a certified dealer for service prior to
winter storage.
Winter service includes operations like cleaning the mower’s parts and
mowing deck, checking for worn parts (such as blade, drive wheels and
other moving parts) and replacing them if required, testing the mower’s
functions and safety components, checking the battery, and uploading
a latest software version, possibly including newly added features.
50 51
Battery replacement
1. Make sure the mower is not in the Base Station.
2. Power the mower off by pressing GO button for 2 seconds.
3. Remove the Disabling Device.
4. Use only a battery that is specified by the manufacturer as a suitable
replacement and ensure you are using the right type (Lead Acid / Li-
Ion) for your mower.
5. Warning! Do not use a non-rechargeable battery.
6. For the orientation of the battery with regard to polarity and the
method of replacement, refer to the instructions supplied with the
replacing battery or to our online Help Center.
7. For the instructions on how to deal with a leaking battery, refer to
the “Batteries” section of the provided safety instructions.
8. Environmental protection:
a. Remove the battery from the appliance before scrapping it.
b. The battery is to be disposed of safely.
c. For additional disposal instructions see the “Product end of use”
section of the provided safety instructions.
No. of
beeps
ON-OFF
indication
Meaning Corrective action
Blinking red Mower crossed
outside / mower
is stuck in place /
lift event detected/
wrong wire connection
Check that the Perimeter Wire is
not too close to the edge or not on
a sloped area.
Move the mower inside the lawn or
away from this particular location
and renew the operation.
Check the ground ditches. Fill with
dirt and level off.
Swap wire connections at the base
station head
• • Blinking red Check the blade /
mow motor overheat
Remove the Disabling Device and
inspect the blade for foreign mate-
rial or debris preventing rotation.
Increase cutting height.
• • • Blinking red No wire signal /
waiting for signal /
wire is cut
Confirm power supply is plugged
into the power outlet.
Check power supply and perim-
ter wire connection to the Base
Station.
Check the indication on the Base
Station. If the wire is cut, repair is
with the provided wire conenctors.
• • • • Blinking red Check drive wheels /
drive motor overheat
Check the drive wheels and
remove grass or other objects.
52 53
Troubleshooting
Simple troubleshooting steps
In case of a fault, the On/Off indication on mower’s panel will light up in red. Press
any button to check for an optional sound indication for the fault. The table below
will guide you to the corresponding action to take.
No. of
beeps
ON-OFF
indication
Meaning Corrective action
None Blinking red
(two LEDs)
No power supply /
charging problem
Confirm power supply is plugged
into the power outlet.
Confirm a good connection of the
power supply to the Base Station.
Clean the charging pins.
None Steady red Other faults Check in the mobile app* or call
the service.
52 53
(*) All faults and corresponding corrective actions are communicated
and described in the app as well. This feature is not available for models
sold in the United States.
Special indications
Indication Meaning
Periodic beeps + ON/OFF LED is red The mower has been lifted or tilted up.
Error sound + Battery LED blinks red two
times
Mowing attempt while the battery is low.
Need to recharge battery first.
Error sound + Lock LED blinks two times Mowing attempt while child protection is
enabled. Press the GO and STOP buttons
together to temporary release the child
protection. Now press GO once or twice to
start mowing.
Error sound + Lock LED blinks three
times
Mowing attempt while theft protection
is enabled. Unlock the mower with a
registered mobile device first.
ON/OFF LED & Battery LED blink
together in red, when the GO button is
pressed
Battery voltage is too low to switch the
mower on. Need to keep charging.
Lock LED blinks three times while ON/
OFF LED is off
The Disabling Device is removed. Insert
the Disabling Device to operate the
mower.
54 55
Rebooting your mower
If for some reason your mower needs to be rebooted, simply switch it off
and on.
Resetting the mower to factory defaults
When it is required to bring the mower to its factory defaults, you may do
so by pressing the GO button for more than 10 seconds (until you hear a
long beep and all LEDs start blinking) while the mower is switched off.
54 55
Frequently Asked
Questions
Mower does not dock properly and sometimes misses Base
Station’s contacts
The entrance to the Base Station is not flat. Fill some ground
to flatten the lawn around the Base Station to allow smooth
entrance. Make sure the Perimeter Wire is laid according to the
installation instructions on the supplied installation template.
Make sure that the Base Station is placed on a relatively level
ground.
Poor mowing quality
The blade may be dull. Remove the Disabling Device. Put on
heavy-duty gloves and inspect the blade. Replace if needed.
Avoid mowing wet grass. For the best cut, operate your mower
when the grass is dry. It is recommended not to mow in the
early morning hours.
Patchy and uneven mowing
Current mowing times are not enough. Increase the time your
mower runs on the lawn. Define additional starting points (not
applicable to models for lawns under 200 m
2
/ 2150 ft
2
) for a
more uniform coverage.
Mower does not depart from base for a long time (not
applicable to models for lawns under 200 m
2
/ 2150 ft
2
)
Use the mobile app to understand the reason for the non-
departure.
56 57
Mower operates at wrong times (not applicable to models
for lawns under 200 m
2
/ 2150 ft
2
)
Verify that the time on the mower is set correctly. The mower’s
time is automatically synchronized when it connects with a
mobile device.
Mower bumps in a rigid lawn’s border too frequently
Move the Perimeter Wire to be at a distance of 45 cm /18” from
any rigid border (like a fence) at the lawn’s edge.
The mower is very noisy
The blade may be damaged or unbalanced. Check if the lawn
is free from branches, stones or other objects that can damage
the blade. Replace the blade if needed.
56 57
Refer to our online
Help Center
for additional
information.
Refer to our online
Help Center
for additional
information.
Appendix A
Additional installation options
1. Internal corner installation.
2. External corner installation.
58 59
Requires
conguring starting
points via the app
(not applicable to
models for lawns
under 200 m
2
/2150 ft
2
)
Appendix B
Secondary areas
Connected secondary areas
If your lawn has additional areas connected with a passage
and the mower is able to drive through it, then you should
bear in mind the following rules:
Separated secondary areas
If your lawn has areas, that are completely
separated (by a fence, sidewalk, pathway, etc.),
then you can extend the perimeter wire to
cover such secondary areas as shown in the
picture below.
• The minimal distance between the wires in such passage
should be 15 cm / 6”
• The minimal width of such passage should be 57 cm / 22”
Min 15 cm Min 57 cm
0 cm
58 59
What to do
Switch ON/OFF
Send the mower to
the Base Station
Blinking green: The mower is
charging in the Base Station.
Blinking red: There is a fault;
go to the“Troubleshooting”
section of this guide or
connect with the mobile app
for more information.
Blinking red fast: The
perimeter wire is cut.
Check the Perimeter Wire’s
connection to the Base
Station. Refer to our online
Help Center for assistance on
finding a wire break.
Start regular mowing
operation (up to 2 hours)
Start short mowing
opration (60 min)
Hold
Press
Press
Press
for 2 seconds
when idle
once
twice
How to do it
Appendix C
Operating basics
Common indications:
Red
Red
Green
60 PB
X-EN
1/Learn
Your Lawn
DOC9043D_EN
MTD Products Aktiengesellschaft Industriestraße 23 • 66129 Saarbrücken • Germany
Contact
us!
5

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Robomow RX50u bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Robomow RX50u in de taal/talen: Engels als bijlage per email.

De handleiding is 2,36 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

Andere handleiding(en) van Robomow RX50u

Robomow RX50u Gebruiksaanwijzing - Nederlands - 64 pagina's

Robomow RX50u Gebruiksaanwijzing - Deutsch - 64 pagina's

Robomow RX50u Gebruiksaanwijzing - Français - 64 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info