512472
53
Verklein
Vergroot
Pagina terug
1/60
Pagina verder
53
Base Station / Perimeter Switch
It is recommended to remove the
Base Station for the winter period:
- Disconnect the power supply from the mains power;
- Open the Base Station / Perimeter Switch cover;
- Disconnect all connectors from the board;
- You can now remove the Base Station cover/ Perimeter Switch and place it in dry storage;
- It is recommended to store the power supply in a dry storage; if not possible, protect the cable
end from moisture to prevent corrosion while not connected to the Base Station.
- Disconnect the green plot connector (keep it connected on the board for the next season) from
the perimeter wire ends and protect it from moisture to prevent corrosion of the wires while not
connected to the Base Station; You may place the Friendly Robotics wire nut connector onto both
wire ends for protection in the winter.
- Protect the remaining connector using the black rubber cover.
After Winter Storage
- Confirm that all connections, charging pins and wire ends are clean prior the first operation; if
required, clean the contacts with a small piece of fine sandpaper, 200 grit or higher or using steel
wool of ‘00’ or higher grade.
- Place the Base Station in its place and connect all cables to the board;
- Confirm that Robomow displays the correct time and date.
5.8 Batteries Replacement
WARNING! Follow the instructions below.
Complete replacement of one battery before starting to replace the
second battery.
Replacing the batteries:
- Lift the bumper and remove the batteries fuse;
- Remove the cutting height adjustment knob by lifting it
upwards (figure 5.4)
- Unscrew the five nuts manually at the rear side of the
Chassis cover (figure 5.5). If you find it difficult use a wide
flat screwdriver;
- Lift the rear side of the cover (see figure 5.6) and
disconnect only the two cables from the left battery (figure
5.7);
- Place the new battery and connect the cables to the
battery tabs when the red and the black cables are fitted
to the color on the battery;
- Disconnect the cables from the right battery;
- Place the new battery and slightly crimp the battery
connectors with plyers, so that they fit tightly on the
battery tabs.
- Connect the cables to the battery tabs respectively by
color;
- Place the cover back in its position and screw the five
nuts manually, confirm they are tight enough;
- Insert the batteries fuse and confirm the Robomow wakes
up.
Figure 5.4
Figure 5.5
Figure 5.7
Figure 5.6
Figure 5.5
Figure 5.4
53

Hulp nodig? Stel uw vraag in het forum

Spelregels
1

Forum

Robomow-RM510

Zoeken resetten

  • Ik krijg constant de melding 'Bumper ingedrukt', de robot blijft dan rondjes draaien rond wijn as en begint niet te maaien. Wat kan ik hieraan doen? De melding verdwijnt en de robot rijdt soms een halve minuut rond wanneer ik tegen de achterbump aanduw tijdens het opstarten van het maaiproces. Gesteld op 10-3-2024 om 11:53

    Reageer op deze vraag Misbruik melden
  • Hoe repareer ik de perimeterdraad eerst koperdraad aan elkaar en dan in de draadconnectoers? Gesteld op 25-6-2019 om 17:37

    Reageer op deze vraag Misbruik melden

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Robomow RM510 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Robomow RM510 in de taal/talen: Engels als bijlage per email.

De handleiding is 3,2 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Robomow RM510

Robomow RM510 Gebruiksaanwijzing - Nederlands - 60 pagina's

Robomow RM510 Gebruiksaanwijzing - Deutsch - 60 pagina's

Robomow RM510 Gebruiksaanwijzing - Français - 61 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info