512474
18
Verklein
Vergroot
Pagina terug
1/44
Pagina verder
Operating & Safety Manual
RM200
www.robomow.eu / www.robomow.com
DOC5202E
2
The products are manufactured by F. Robotics Acquisitions (Friendly Robotics).
Friendly Robotics products are CE approved.
Friendly Robotics products comply with the requirements of the RoHS
(Restrictions on Hazardous Substances) Directive 2002/95/EC and the WEEE
(Waste Electrical and Electronic Equipment) Directive 2002/96/EC.
© Friendly Robotics, 2010-A. All rights reserved. No part of this document may be photocopied,
reproduced, electronically or translated without the prior written consent of Friendly Robotics.
Product, product specifications and this document are subject to change without notice. All other
trademarks are property of their respective owners.
Welcome to the world of home robotics with the Friendly Robotics Robomow!
Thank you for purchasing our product. We know that you will enjoy the extra free time you will have
while using Robomow to mow your lawn. When set up and used properly, Robomow will operate
safely on your lawn and provide you with a quality of cut matched by a few mowers of any kind. You
will be impressed with your lawn’s appearance and best of all, Robomow did it for you.
IMPORTANT!
The following pages contain important safety and operating instructions.
Please read and follow all instructions in this manual. Carefully read and
review all safety instructions, warnings and cautions contained in this manual.
Failure to read and follow these instructions, warnings and cautionary statements
may result in severe injury or death to persons and pets or damage to personal property.
3
Table of Contents
Safety Warnings & Precautions………………………………………………………….…………..
4
Warnings Decal Definitions…………………………………………………………………………...
6
Robomow
®
Safety Features………………………………………………………………………….
7
How It Works…………………………………………………………………………………………….
8
What’s in the Box……………………………………………………………………………………….
9
Chapter 1 - Perimeter Wire Setup………………………………………………………..………....
10
1.1 Preparations………………………………………………………………………………… 10
1.2 Planning the Setup………………………………………………………………………… 10
1.3 Perimeter Wire Setup………………………………………………………………………. 14
1.4 Robomow Preparation and Settings……………………………………………………… 17
1.5 Completing the Wire Fastening…………………………………………………………… 19
Chapter 2 – Menu………………………………………………………………………………………..
20
2.1 Zones Setup…………………………………………………………………………………. 21
2.2 Settings………………………………………………………………………………………. 21
2.3 Information…………………………………………………………………………………… 23
Chapter 3 – Operation and Charging…………………………………………………………….….
25
3.1 Edge Mowing ……………………………………………………………………………….. 25
3.2 Scanning (Mowing of the inner area)……………………………………………………... 25
3.3 Skipping Edge Mowing …………………………………………………………………….. 25
3.4 Operation …………………………………….……………………………………………… 25
3.5 Completing the Operation… ………………………………………………………………. 25
3.6 Charging……………………… …………………………………………………………….. 26
Chapter 4 – Text Messages and Troubleshooting………………………………………………...
27
4.1 Messaging…………………………………………………………………………………… 27
4.2 Other Operational or Fault Problems……………………………………………………... 31
Chapter 5 – Maintenance and Storage………………………………………………………………
33
5.1 Recommended Maintenance Schedule ………………………………………………….. 33
5.2 Cleaning……………………………………………………………………………………… 33
5.3 Battery………………………………………………………………………………………... 33
5.4 Replacing the Blade ………………………………………………………………………... 34
5.5 Splicing the Perimeter Wire ……………………………………………………………….. 35
5.6 Winter Storage……………………………………………………………………………….
5.7 Batteries Replacement……………………………………………………………………...
35
36
Chapter 6 – Specifications…………………………………………………………………………...
37
Chapter 7 – Accessories…………………………………………………………………………….…
38
Tips for maintaining your lawn……………………………………………………………………….
39
Friendly Robotics RM/City Series Limited Warranty…………………………………………...
EU Declaration of Conformity ……………………………………………...……..……………………
40
41
4
Safety Warnings & Precautions
Training and Instructions
1. Read this manual carefully before operating Robomow
. Be familiar with the controls and the
proper use of Robomow
and follow all safety and warning instructions.
2. Do not use Robomow
for any purpose other than for which it is intended.
3. Never allow children or people unfamiliar with these instructions to operate Robomow.
4. Never mow while people, especially children, or pets are nearby.
5. The user is responsible for accidents or hazards occurring to other people or their property.
6. It is strongly recommended to use the ‘Child Guard or ‘Anti theft menu option in order to
prevent operation by children or other who are not familiar with the safe operation of the mower.
7. The appliance is not to be used by children or persons with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless they have been given supervision or
instruction. Children should be supervised to ensure they do not play with the appliance.
8. Warning! When there is a risk of lightning storm, disconnect the perimeter wire from the Perimeter
Switch and the Power Supply 230V/120V plug from the mains socket
Preparation
9. Make sure to layout and set up the perimeter wire according to the instructions.
10. While mowing using a Remote Control always wear substantial footwear and long trousers.
11. Periodically inspect the area mowed by Robomow
, and remove stones, sticks, wires, bones and
other objects. Objects struck by the blade may be thrown and cause severe injuries to people.
12. Only use accessories and attachments designed for this product.
Operation
13. Caution! Do not touch rotating blade!
14. Remove the fuse whenever Robomow starts vibrating abnormally or after striking an object.
15. Never let Robomow operate without supervision.
16. When using the Remote Control mow only in daylight or in a good artificial light.
17. Do not operate Robomow
using the Remote Control when barefoot or wearing open sandals.
Always wear substantial footwear and long trousers.
18. Avoid operating Robomow
on wet grass. Do not use it in rain.
19. When using Remote Control always be sure of your footing on slopes.
20. Do not operate the mower on slopes greater than 18 degrees.
21. Keep all guards, shields, safety devices, and sensors in place. Repair or replace damaged parts,
including decals. Do not operate Robomow
if any parts are damaged or worn.
22. Do not operate Robomow
if any safety feature or device is damaged or inoperable.
23. Do not attempt to disable or defeat any safety feature or device.
24. When using the Remote Control always switch on the motor according to instructions and with feet
well away from the blade.
25. This machine has sharp rotating blade! Never operate the mower if unattended; keep bystanders,
children and pets away from mower when in operation.
26. Never allow anyone to ride or sit on mower.
27. Keep hands and feet away from the cutting blade and other moving parts.
28. Never pick up or carry this appliance while the motors are running.
29. Never attempt to service or adjust the mower while it is in operation.
30. Do not touch the blade before the fuse has been removed and the blade has come to a complete
stop.
31. Never raise the mower or attempt to inspect the blade while the mower is operating.
32. Always remove the fuse before lifting the mower or attempting any adjustments.
5
Bum
p
e
r
Transport
To safely move from or within the working area:
33. Use the Remote Control (available as an accessory) to
drive it from place to place (See section 2.4).
34. In case of different height level or stairs, turn off the mower
by pressing the Main Switch button, lift the bumper door,
located at the top of the Robomow, and carry the mower by
the carrying handle, while the rear bottom side is laying on
your thigh, as shown in the right figure.
35. In case of long transportation by car it is required to remove
the fuse and use the original packaging.
Maintenance and storage
36. Maintain, service, and store Robomow
according to the instructions (refer to chapter 5).
37. Remove the battery fuse before working on or lifting Robomow. Remove the battery fuse before any
maintenance is done.
38. Keep all nuts, bolts, and screws tight to assure safe condition of this appliance.
39. Replace worn or damaged parts for safety.
40. Use heavy gloves when inspecting, servicing or replacing the blade.
41. Use only the original equipment, batteries and power supply/charger with this mower. Incorrect use may
result in electric shock, overheating or leakage of corrosive liquid from the battery.
42. Do not open or mutilate the battery. Released electrolyte is corrosive and may damage the eyes or skin.
43. Wear eye protection and use gloves when setting the perimeter wire and driving the wire stakes/pegs.
Firmly drive all pegs in order to keep the wire from becoming a tripping hazard.
44. Do not use the power supply/charger if the cord has damaged.
45. A spark may be created when inserting the fuse to the robot. Therefore it is forbidden to perform these
tasks close to flammable materials. It is also forbidden to use spray or any other cleaning materials for
cleaning electronic contacts, due to this risk of inflammation when inserting the power pack or fuse.
Product end of use
46. Robomow and its accessories should be collected separately at the end of their life to prevent waste
electrical and electronic equipment from ending up in landfill sites, to promote the reuse, treatment and
recovery of electrical and electronic equipment in purpose to preserve, protect and improve the quality
of the environment, protect human health and utilize natural resources prudently and rationally.
47. Do not dispose Robomow or any other part of it (including the Charger, Base Station and Perimeter
Switch) as unsorted municipal waste – it should be collected separately.
48. Ask your local distributor/dealer about return and collection systems available.
49. Do not dispose of the batteries in a fire and do not place used batteries in your household trash. The
batteries must be collected, recycled, or disposed of in an environmentally sound manner.
6
1 2 3 4 5 6 7
Warnings Decal Definitions
These are the symbols on Robomow
; Read them carefully before operating Robomow
.
DANGER! Sharp rotating blade. Keep hands and feet away.
Serious injury can occur. Caution – Do not touch rotating blade
1. Safety alerts symbol – WARNING - this is a dangerous power tool. Use care when operating
and follow all safety instructions and warnings.
2. Read operator’s manual – Read user instructions before operating your Robomow
3. Hazard of Thrown or flying objects - Whole body exposure, take caution.
4. Keep a safe distance from the machine when operating
Keep people in particular children, pets and bystanders away from the area in which
Robomow is being used.
5. Severing of toes or fingers - Rotary mower blade
Risk of injury from rotating cutting blade. Keep hands and feet away and do not attempt to
lift Robomow from this area.
6. Remove the Fuse before working on or lifting Robomow.
. Remove the Power Pack before
working on or lifting Robomow
.
7. Do not ride on Robomow
.
Disposal of old Electrical & Electronic Equipment
Do not dispose Robomow or any other part of it as unsorted
municipal waste – instead it shall be handed over to the applicable
collection point for the recycling of electrical and electronic equipment.
EC Conformity
This product conforms to the applicable EU Directives
7
Robomow
®
Safety Features
1. Child Guard / Safety Guard (Level I)
This menu option offers a safety feature to help prevent children or others not familiar with the safe operation
of the mower to operate it freely.
2. Anti-Theft / Safety Guard (level II)
The anti-theft system provides the user a disabling function that will prevent anyone from using or driving the
Robomow unless they have the valid code to enter. You will be prompted to enter a four-digit code of your
choice to use as your personal security code.
3. Lift Sensor
There is Hall-Effect Sensor (Magnetic Position Sensor) located in the front side of Robomow. In
case the front of the mower is raised approximately 1-inch from its resting position on the ground
during blade operation, the blade will immediately stop rotating (< 1 second).
4. Tilt Sensor
There is an optical sensor located in the front side of Robomow. In case the front of the mower is lifted up
towards a vertically position, the blade will stop immediately and Robomow will warn about it and instruct the
user to remove the fuse before lifting Robomow.
5. Bumper Sensor
The bumper is equipped with Hall Effect sensor activates when the mower strikes a solid, fixed object and
when the bumper cover is open. When the bumper sensor is activated, the mower will stop the rotation of
the blade immediately (<1 second), will stop movement in that direction and reverse itself away from the
obstacle.
6. Emergency Stop Button
Located on the control panel, red in color. Pressing this button at any time during operation will stop all
mower movement and stop the rotation of the blade immediately (<1 second).
7. Batteries Fuse
Located below the bumper cover, on the left side of Robomow. Removing the battery fuse will prevent any
operation of the Robomow. It is required to remove the fuse before lifting Robomow and before any
maintenance is done.
8. Two-Step Operator Presence Control
While in manual mode using the remote control, it requires two independent finger actions in order to engage
the mower blade. Once engaged, the mower blade button must remain depressed to continue blade
operation. Once released, the two-step engagement process must be repeated.
9. Electronically Controlled Charging System
Robomow is equipped with an on-board charge control system. This allows you to keep the charger
connected at all times, even after the battery is fully charged. The control system will prevent an overcharge
to the battery and keep it fully charged and maintained for the next use.
10. Sealed Batteries
The batteries that operate the Robomow are completely sealed and will not leak any type of fluids,
regardless of position. In addition, the batteries contain a one-time-use fuse in the event of a short-circuit or
power malfunction.
11. Perimeter Switch and Perimeter Wire
Robomow cannot operate without a perimeter wire installed and activated through the Perimeter Switch. In
the event the Perimeter Switch is turned off or otherwise fails to function, Robomow will stop operating.
Likewise, should a break in the perimeter wire occur Robomow will again stop operation. A break in the
perimeter wire prior to operation will prevent Robomow from operating. It can only operate within the
boundary of the perimeter wire.
8
12. Over-heat Monitoring Protection
The blade motor and each of the two wheel drive motors are monitored continuously during operation for any
situation that may cause these motors to over-heat. In such event, Robomow will stop operation of at least
that motor and possibly the mower itself and indicate that the motor is cooling down. While unusual, this may
happen when the mower is on grass that is severely overgrown; the underside of the mower is clogged from
poor cleaning maintenance; the mower has encountered an obstacle that is unable to activate the bumper
sensor preventing it from moving; or a problem landscape area has caused the mower to get stuck and is
preventing it from moving.
How It Works
A small wire, called the perimeter wire, is placed around the perimeter of the lawn and any other areas where you
do not want the mower to enter. A small signal is generated from a device attached to the perimeter wire, called the
Perimeter Switch. When turned on, this signal is carried through the perimeter wire, creating what we define as a
virtual wall. The virtual wall is visible only to Robomow, keeping Robomow where you want it, on your lawn. The
perimeter switch must be turned on to activate the perimeter wire before Robomow will operate.
WARNING!
This warning symbol will be found at several
points throughout the pages of this manual.
It is intended to highlight an important safety,
warning or cautionary message.
Please pay particular attention to these
areas and be sure you fully understand
the message before proceeding.
Perimeter Switch
Virtual wall
9
Wire
Pegs
Power Supply
(for charging
Robomow)
Perimeter
Switch
Indoor Power Supply
for Perimeter Switch
What’s in the Box
Open the box and lift the Robomow from its carrying handle.
RoboRule
r
Robomow
Plot
Connector
Wire
Connector
Charging
Adaptor
10
Wires leading from the perimeter
to the Perimeter Switch are
adjacent and touching.
Indoor Power
Supply
Zone A
The Perimeter Switch MUST be
mounted vertically in order
to maintain its’ water resistance
Wires leading from the perimeter
to the Perimeter Switch are
adjacent and touching.
Indoor Power
Supply
Zone A
The Perimeter Switch MUST be
mounted vertically in order
to maintain its’ water resistance
Chapter 1 - Perimeter Wire Setup
1.1 Preparations
Read carefully the Operating and Safety Manual prior to setup.
It is recommended to mow your lawn using a conventional lawn mower and water the ground before
starting the setup for easier driving of the pegs.
Confirm all parts for the setup are included (refer to ‘What’s in the Box’ page 9).
During the setup you will also need the following tools:
1.2 Planning the Setup
1.2.1 Perimeter Switch Location
Find a convenient spot outside the perimeter, but a location that is relatively easy for you to
access.
The Perimeter Switch must be mounted vertically in order to maintain its’ water resistance and
preferably in a dry and sheltered location.
Close to a wall socket (230V/120V) – as it is connected to an indoor Power Supply.
1.2.2 Placing the Perimeter Switch
The Perimeter Switch connector is designed for quick and easy
disconnection that allows you to easily move the perimeter switch
between plots.
The Perimeter Switch also comes with a large stake that
fastens to its back, making transfer from one plot to
another easier by allowing you to disconnect the switch
and move it with the stake still attached (Figure 1.3).
Hammer
Combination
Pliers
Small flat and
Philips screwdrivers
Fi
g
ure 1.1
Tools required for the setup
IMORTANT INFORMATION! Before starting the setup, it is necessary to first
read this chapter in order to be aware of all setup rules and instructions so you are able
to determine the best location for the Perimeter Switch and the perimeter wire layout.
Figure 1.2
Perimeter Switch
Location
Figure 1.3 - Perimeter
Switch with stake attached
11
Another option is to mount the Perimeter Switch onto a
vertical surface, such as a wall or deck railing. There are
three small bosses on the back of the switch cover in
order to mount it this way. (Figure 1.4).
1.2.3 Multiple Zones/Areas And Narrow Passages
Your home may require more than one zone to be set up in
order for the Robomow to work in all of your lawn effectively.
Where grass areas are not contiguous, or are separated by
fences, sidewalks or other objects, it is required to make each
of these a separate zone.
When setting separated zones there are two options to lay the
wire:
Option A
: All zones are looped together and connected to the
Perimeter Switch. Perimeter wire can be as long as 500
meters (1650ft) in one loop when connected to the Perimeter
Switch (Figure 1.5).
Option B
: There are separated zones. The Perimeter Switch can be moved between different
zones (Figure 1.6).
To mow other areas, simply drive or carry Robomow to the area you want to mow and operate it. In
this way, if one zone needs a shorter operating time than another, it can easily be set (Chapter
2.1.1). When this area is completed, drive the mower back for re-charging.
Determining the distance between adjacent perimeter wires:
1. If lawns are installed by the same perimeter wire that is connected to the same
source (Base Station / Perimeter Switch), then it is enough to keep a distance of one
meter between the wires to prevent interference in operation.
2. If lawns are installed using different perimeter wires that are not connected, and
each has its own source (Base Station / Perimeter Switch), then one of the following
is required:
a. Maintain a minimum distance between the wires (30-50cm) to allow overlap
between mowing zones, but synchronize between the mowing schedules to
confirm there will not be interference between the zones. OR
b. Keep two meters between the perimeter wires with no need to synchronize
between the operation schedules.
Figure 1.5 (Option A)
Two zones are looped
together and connected
to the Perimeter Switch
Distance between wires
greater than 1 meter (3ft.)
Wires leading to the next plot
are parallel and touching. The
gap between them is for
illustration only.
Zone A
Zone B
Zone A
Perimeter
Switch
Figure 1.4 - Squeeze the tabs on
both sides to remove cover
Mounting the Perimeter Switch using
three mounting bosses on back cover
12
Where grass areas are contiguous, with minimum 1 meter (3ft) between the wires Robomow can effectively
navigate through in order to move between the two areas while mowing the lawn, otherwise separate the
area into different zones.
The area that connects two attached big areas is called a narrow pass (Figure 1.7):
Figure 1.6 (Option B)
Separated zones, where grass
areas are not contiguous
Distance between wires
greater than 1 meter (3 ft.)
Perimeter
Switch
Zone A
Zone A
Zone B
Figure 1.7 - Multiple areas with narrow passes
Narrow Pass
At least 1m (3ft) between
wires so Robomow can
effectively navigate
through in order to move
between the two areas
while mowin
g
the lawn.
When area width between
perimeter wires is less than
1m (3ft), leave the narrow
area out of the zone
Zone A
Zone A
Zone B
Perimeter
Switches
13
1.2.4 Defining Obstacles-Perimeter Islands
Obstacles that are relatively rigid and higher than 15cm (6 inches), such as trees, phone poles and
power poles can be left in the lawn without any consideration during the wire setup. The Robomow
will turn when it collides with this type of obstacle.
Other obstacles such as, flowerbeds, fountains and small trees, must be protected from the
Robomow using the perimeter wire. This is done as part of the setup process and is commonly
referred to as a perimeter island. However, for the most gentle and silent operation, it is preferable to
demarcate all fixed objects in the working area.
To create a perimeter island (Figure 1.8):
Take the wire from the perimeter section closest to the obstacle;
Peg it around the obstacle, using the RoboRuler short distance;
Returning back to the same spot of the edge you started from;
The wires leading to the perimeter island and coming back to the edge should be parallel and
touching BUT they cannot be crossed. The wires to and from the perimeter island can be secured
with the same pegs. The mower will not recognize these two wires and mow over them as if they do
not exist. The single wire around the perimeter island will be recognized and prevent the mower from
entering this area.
Areas with obstacles grouped closely together should be covered by a single perimeter island or if
they are close to the edge of the lawn, leave them out of the designated area.
1.2.5 Slopes
The Perimeter Wire should not be laid across a slope that is steeper than 15cm (6in) per distance of 1
meter/3.3ft (15%). There is a risk that Robomow will find it difficult to turn and might cross the wire outside,
especially in damp weather conditions, as the wheels can slip on the wet grass.
However, the perimeter wire can be laid across a slope steeper than 15% if there is an obstacle (fence,
wall or dense hedge) that can prevent Robomow from slipping out of the area.
The maximum slope limit Robomow can mow inside the working area is 33%, roughly equals to 33cm (1ft)
of rise per 1 meter (3ft). In any event, a slope that causes the front of the mower to raise from the ground
while climbing is too steep and should not be included as part of the cutting area (see area marked as 'B' in
Figure 1.9). Sloping area greater than 33% cannot be included in the working area.
While the picture shows two
wires separate, they should
be adjacent and placed
under the same pegs
Perimeter wire
Perimeter Switch
Direction of set-up
followed around obstacle
Figure 1.8 -
Perimeter Islands Setup
Minimum distance of 1m (3ft) between two adjacent
wires of perimeter islands, otherwise demarcate them
together as shown as one perimeter island
Caution! Setting the Perimeter Wire
counter-clockwise around the
obstacle will cause Robomow to
drive into the island".
14
34cm / 14inch
Long distance
of RoboRuler
100 cm
0-15 cm
This area should be
left out of the
working area
as the perimeter wire
cannot be laid in slope
greater than 15%
(15cm height per
distance of 1m)
Robomow can mow
areas inside the
working area with
slope up to 33 cm
per distance of
1 meter (33%)
Slope
0-15%
Slope
0-33%
x
A
B
C
D
1.3 Perimeter Wire Setup
Now, knowing the location of the Perimeter Switch and the planning of the wire layout, you can begin to
setup the Perimeter Wire.
1.3.1 Starting Point
Place the Perimeter Switch according to your plan, as
shown in Figure 1.2;
Puncture the plastic covering of the perimeter wire and
pull the wire ends with the plot connector out of the
plastic covering; The connector should be connected to
the wire in the polarity show in Figure 1.10;
The plastic covering is designed as a dispenser for the
wire; so do not remove the wire spool from the covering;
Peg the beginning of the wire to the ground where the
Perimeter Switch will be located; be sure to leave spare
wire to close the loop at the end of the setup (Figure
1.11);
Lay the wire from the Perimeter Switch to the lawn;
Start laying the wire to the counterclockwise direction when standing inside the lawn, as show in Figure
1.11.
Begin pulling the perimeter wire out of the plastic covering and lay it loosely as you walk along the area of
the lawn to the direction shown in Figure 1.11;
Figure 1.9 - Max slope
Figure 1.10 – Pull out the wire from the plastic
covering – do not remove the covering; it is
designed as a dispenser.
Connect the wire end to
the left side of the plot
connector (when facing
towards the screws)
Perimeter wire layout in
clockwise direction (as viewed
from the inner side of the lawn)
Figure 1.11 –
Direction of Perimeter Wire
layout from the Perimeter Switch
15
1.3.2 Laying Out the Perimeter Wire
Start setting the perimeter wire by placing pegs every few meters and at the lawn corners according to
your plan; do not forget obstacles that need to be demarcated while laying the wire.
After removing enough wire within a given section, use the RoboRuler provided to set the correct distance
from the lawn edge. The RoboRuler is used to help position the perimeter wire along walls, fences,
sidewalk, driveways, flowerbeds and other perimeter zones.
There are two basic measurements that are used on the RoboRuler (Figure 1.12).
The shorter distance is used along perimeter edges where the area outside the immediate perimeter is
free of obstacles and is the same relative height as the perimeter edge or lower (sidewalk on the same
level or flowerbeds).
The longer distance is used along perimeter edges where the area outside the immediate perimeter has
obstacles or differences in the height along the perimeter edge (walls and fences).
Important
If the lawn's edge borders with a pond, swimming pool or watercourse or where the grass level is higher
than 70cm (2ft) from the edge around it, then it is required to keep a distance of at least 1.2m (4ft)
between the wire and the water (or chasm) otherwise supplement a fence or the same along the lawn's
edge, so Robomow can detect it. The height must then be at least 15cm (6 inch). This will prevent
Robomow, under any circumstances, from crossing the wire outside the working area
1.3.3 Fastening The Wire To The Ground
It is not necessary to bury the perimeter wire, though you may do so if you wish, up to 10 cm
(4 inches) deep.
Small pegs or stakes are supplied with the Robomow and they are used to fasten and hold the
perimeter wire to the ground, below grass level.
Initially place a minimum number of pegs to fasten the wire down. Remember that you will want to test
the wire set up before you fill in additional pegs and you may find some areas where you will need to
move the wire position slightly.
Upon hammering the peg to its final depth in the ground, pull the wire tight. It is a lot easier to insert
pegs into wet soil. If the soil is dry, water the yard before perimeter wire set up.
WARNING!
Damage to the eye is possible. Use proper eye protection and wear
appropriate work gloves when hammering the pegs. Hard or dry ground
may cause pegs to break when driving them in. In extreme cases,
watering the lawn where the pegs will be driven can be beneficial.
Short distance of RoboRuler
– where the area outside
the immediate perimeter is
free of obstacles and is the
same relative height as the
perimeter edge or lower
Long distance of
RoboRuler – where
the area outside the
immediate perimeter
has obstacles or
differences in the
height along the
p
erimeter ed
g
e
Figure 1.12 – using the RoboRuler
16
Add pegs in to pull
the perimeter wire down
to the ground surface,
below the grass tips.
Add pegs in to pull
the perimeter wire down
to the ground surface,
below the grass tips.
Pegs should be driven at distances between one another
that will keep the wire down below the grass level and
prevent it from becoming a tripping hazard (Figure 1.13).
When properly fastened to the ground, the wire and pegs
will soon disappear under the growth of new grass and will
not be visible.
If additional wire is required in order to complete the set-
up, use the wire connectors provided, which are
waterproof, to connect between the two wire ends, as
explained in chapter 5.5.
1.3.4 Completing The Perimeter Wire Setup
Once the perimeter wire is completed and pegged to the ground, the last step to complete is attaching
the Perimeter Switch to the perimeter wires and testing the setup.
Pull the two loose perimeter wire leads taut and peg them down to the ground (figure 1.2), adjacent to
one another, as you move away from the perimeter and towards the Perimeter Switch location (use the
same pegs to attach the two wires from the lawn to the Perimeter Switch location).
There are two loose wire ends where the perimeter wire set up was started (Figure 1.14).
Use the same peg to fasten these two perimeter wire ends down to the ground and twist them.
Cut the wire end without the connector so they are of equal length - removing any excess wire.
Strip back 6 mm (0.25 inches) of insulation from the wire end (Figure 1.15).
Insert the free perimeter wire into hole of connector using a small flat screwdriver; tighten the screw to
secure the perimeter wire into the connector (Figure 1.16).
Plug the perimeter wire connector into the Perimeter Switch (see figure 1.17)
IMPORTANT INFORMATION!
Screw terminals or twisted cables, insulated with insulation tape
is not a satisfactory splice. Soil moisture will cause the stripped
wire ends to oxidize and after a while result in broken circuit.
Figure 1.13 -
Pegging the Perimeter Wire
Figure 1.17
Plug the plot connector into
the Perimeter Switch
Figure 1.15 -
Strip 6mm (0.25 inches) of insulation from the wire end
Figure 1.14 -
Two loose wire ends at the starting point
Figure 1.16 -
Tighten the screw to secure the
perimeter wire into the connector
17
Figure 1.19
Perimeter Switch
Operating Panel
Flashing light
indicates the s
y
stem
Indicates poor splicing of
perimeter wires or perimeter
wire, which is too long
Indicates a
disconnected/broken
ON
button
Take the Perimeter Switch and squeeze the tabs on
both sides of the Perimeter Switch, (as shown in
figure 1.18a) and remove the back cover from the
Perimeter Switch.
Connect the power supply plug to the Perimeter
Switch board (see figure 1.18b) and reassemble the
Perimeter Switch.
Connect the power supply to a regular household
receptacle 230/120 Volts AC;
The Power Supply is for indoor use only, thus place
it in a dry location, which is well ventilated (do not
cover it with plastic bag); be sure the power supply
and the connection to the low voltage cable are in a
dry place and not exposed to water and rain.
Press the ‘ON’ button. A small flashing green light next to the ‘ON button indicates that the system is
on and functioning properly. The Perimeter Switch also has indicators for a disconnected/broken
perimeter wire and for
poor wire splicing. Figure 1.19
The Perimeter Switch has an automatic shutoff feature, eliminating the need for you to turn it off after
each use. It will shut itself off after 12 hours of operation. You may manually turn the perimeter switch
off by pressing the ‘ON’ button continuously for 3 seconds. A beep will be heard after the three
seconds, indicating you may release the button and the switch is off.
1.4 Robomow Preparation and Settings
1.4.1 Setting the Cutting Height
Lift the Bumper Cover from the front side of the Robomow (figure 1.20).
To change the cutting height, rotate the cutting height adjustment knob (see figure 1.21).
Figure 1.18b
Connect the power supply plug
to the Perim
eter Switch board
Figure 1.20 -
Lifting the Bumper Cover
Figure 1.21 -
RM200 General View
Cutting height
adjustment
knob
Mowing
motor
Carrying
handle
Power Supply
connection
Fuse locationControl Panel
Figure
1.18a
18
STOP
GO
STOP
GO
Operating Lamp
UP
arrow
DOWN
arrow
Rain
sensor
LCD display
window
GO / START
button
Main Switch
button
STOP button
Language
Press GO
00:00 dd/mm/yy
next digit
Time and Date
Press GO
English (US)
Confirm
Press ‘GO
Scroll ‘UP’ or ‘DOWN’
to choose your language
and press GO to confirm
Press ‘GO
Scroll to set the time and date
and pressGO’ for the next digit
(‘STOP’ is used to go back)
15:23 16/04/07
Confirm
Please note that there are
English’andEnglish (US)’ under
the ‘Language’ menu, as the language
defines also the ‘Time and date’ format.
Press ‘GO’ to confirm and continue
with the instructions at the next
subparagraph (‘Wire position’ test)
Language
Press GO
Language
Press GO
00:00 dd/mm/yy
next digit
00:00 dd/mm/yy
next digit
Time and Date
Press GO
Time and Date
Press GO
English (US)
Confirm
English (US)
Confirm
English (US)
Confirm
Press ‘GO
Scroll ‘UP’ or ‘DOWN’
to choose your language
and press GO to confirm
Press ‘GO
Scroll to set the time and date
and pressGO’ for the next digit
(‘STOP’ is used to go back)
15:23 16/04/07
Confirm
Please note that there are
English’andEnglish (US)’ under
the ‘Language’ menu, as the language
defines also the ‘Time and date’ format.
Press ‘GO’ to confirm and continue
with the instructions at the next
subparagraph (‘Wire position’ test)
Your Robomow is shipped with the batteries fuse removed and
it will not operate without it. The fuse is supplied in a small plastic bag
attached to the Robomow (located under the Bumper Cover).
Lift the Bumper Cover and insert the fuse. The fuse can be inserted in
either direction. See figure 1.22
Robomow will now power up (wake up). The Batteries are charged at the
factory and have plenty of power to perform the initial setup and test run.
However, after the initial set-up process is completed the batteries need
to be charged 16 hours in the Base Station before the first operation.
1.4.2 Robomow Settings
Control Panel
On the top of the rear side of Robomow there is a control panel. The control panel consists of a
display, keypad and operating lamp (figure 1.23).
The ‘GO’ button is used as a means to select or confirm different menu options or settings;
‘Up / Down arrow keys will allow you to scroll through the menu items;
The ‘STOP’ button has two different functions: when pressing during automatic operation it will stop
Robomow and blade operation immediately and when pressing at any time during the menu selection
process it will bring you one step back in the menu.
‘Main Switch’ button is used to switch off the Robomow. It is required to switch off the Robomow
when carrying it between zones.
IMPORTANT INFORMATION!
Follow the instructions on the LCD display -
Robomow will friendly instruct you, step by step, how to complete the setup
Language, Time and Date settings
Language’ is the first setting you are asked to set, as Robomow wakes up. Follow the
instructions below, as shown in figure 1.24.
Figure 1.22 -
Inserting batteries fuse
Figure 1.23
Control Panel
Figure 1.24
Language, Time
and Date setting
19
Wire position
Press GO to test
Press ‘GO’to test
wire position
Wire position
Robomow collides
with obstacle, drives
back and stops
Adjust wire
then press GO
Adjust the wire and press ‘GO’to
continue testing the wire position
Walk along the side of the
Robomow while it is following
the edge until completing one
lope of the perimeter without
striking any object (it will stay
in the Base Station).
Wire position
Press GO to test
Wire position
Press GO to test
Press ‘GO’to test
wire position
Wire positionWire position
Robomow collides
with obstacle, drives
back and stops
Adjust wire
then press GO
Adjust wire
then press GO
Adjust the wire and press ‘GO’to
continue testing the wire position
Walk along the side of the
Robomow while it is following
the edge until completing one
lope of the perimeter without
striking any object (it will stay
in the Base Station).
Follow the instructions, as shown in figure 1.25 to complete the test of the Perimeter Wire position:
Test the perimeter wire setup by choosing the ‘
Wire position’ test (If required to find the ‘Wire position’
menu refer to Figure 2.1). Robomow will follow the wire, while the mowing motor is switched off to prevent
any damage to the perimeter wire after the initial setup; Walk along the side of the Robomow while it is
following the edge until completing one loop of the perimeter without striking any object; If Robomow
collides in obstacle, it stops and drives back to allow you adjusting the wire position.
1.5 Completing the Wire Fastening
Once complete, walk back along the perimeter and add in wire pegs to those areas of the wire where it is
not pulled down below the level of the grass tips and close to ground level. Wherever the wire is raised or
loose, it should be tightened and pegged down with extra wire pegs (distance between pegs should be 0.5
to 1 meter in straight line and more when curved).
Figure 1.25
Testing the Perimeter Wire position
20
Figure 2.1
Robomow menu options
Chapter 2 - Menu
Chapter 2 introduces Robomow menu functions. To use the control panel read the instructions in paragraph
1.2.4.
The main menu consists of four options: 2.1 Zones setup
2.2 Settings
2.3 Information
2.4 Service (password is required)
Note: the numbers 2.1-2.4 refer to the headings on the coming pages.
To browse through the main menu and the submenus, use the
GObutton as a means to select or confirm
different menu options or settings. Pressing the
GO button will generally select or confirm the text message
shown on the second line of the LCD. There are several settings, which the user can make changes to and
features that can be enabled/disabled. Pressing the STOP button at any time during the menu selection
process will bring you one step back in the menu. To scroll between the submenus use the ‘
UP’/’DOWN’ arrow
keys.
To see the main menu functions (options 2.1 to 2.4 - Figure 2.1), follow one of the following options:
1. When the mower is
out of the Base Station scroll down to the ‘User options’ display and press ‘GO’;
2. When the mower is
in the Base Station, simply scroll down to the menu you want.
Figure number 2.1 shows the main menu and the submenus available under each of the options. There are
more submenus in the next level of the menu tree that are explained in the next pages of this chapter.
Press GO to receive
options 2.1 to 2.3
Scroll UP/DOWN
using the arrow keys
to the menu you want
and press GO to see
the options below the
chosen menu
21
Figure 2.2
Zones setup options
Set zone: A
Set zone: B
Work time
Learn edge
Set default edge
2.1.1
2.1.1.1
2.1.1.2
2.1.1.3
Set zone: A
Set zone: B
Work time
Learn edge
Set default edge
2.1.1
2.1.1.1
2.1.1.2
2.1.1.3
2.1 Zones setup
The Zones setup’ menu allows user to set the parameters that are specific per zone.
It is possible to set up to two different zones: zone A and B, when the main zone is
Zone A.
2.1.1 Set zone: A (or B)
Allows user to set the parameters that are specific per non-Base Station zone (figure 2.2):
2.1.1.1 Work time
Allows the user the option of setting the operating time from 15 minutes up to 2 hours and ‘MAX’ which
is generally 2.5 hours, depending on grass type and condition.
2.1.1.2 Learn Edge
The default distance for edge mowing is approximately 1 to 2 rounds around the perimeter. This feature
allows the user to define a specific distance in each operating zone in order to have the mower cut the
edge at a specific distance. It will remain as a learned distance until the edge is re-learned or the ‘Set
default edge’ is selected. To learn edge distance follow the instructions below (figure 2.3):
2.1.1.3 Set Default Edge
Selecting Default Edge restores the factory default edge distance to the specific zone selected.
2.2 Settings
The ‘Settings’ menu allows the user to set the options that refer to the Robomow itself and are
common to all zones (figure 2.1).
2.2.1 Child Guard
Child guard is a feature that when activated will help deter use by young children and other
unauthorized people. It will prevent operation to those not familiar with the mower. The key sequence to
unlock the guard for operation is pressing the ‘UP’ arrow key and then the ‘STOP’ key to unlock the
controls. Two minutes of inactivity will re-lock the keys.
It is strongly recommended to use the “Child Guard” menu option in order to prevent operation
by children or others who are not familiar with the safe operation of the Robomow.
2.2.2 Anti-Theft
The anti-theft system provides the user a disabling function that will prevent anyone from using or
driving the Robomow unless they have the valid code to enter. You will be prompted to enter a four-digit
code of your choice to use as your personal security code. Use the scroll arrows in order to change
each digit position to a different number and then press
‘GO’ to move to the next digit to select. You will
find a place to record your personal security code in Chapter 8 of this manual. Be sure to record your
code for future reference.
To change the password, choose the
‘Change code’ option under the ‘Anti theft’ menu. You will be
promoted to enter your old password before setting the new one.
Figure 2.3
Learn edge
Set zone: A
Press GO
Scroll DOWN once to
‘Learn edge’ option
Scroll to the zone of which
you want to learn the edge
distance and press ‘GO
Press ‘GO’ to start
the learning process
Work time
Press GO
Learn edge
Press GO
Learning edge
STOP to set
While driving around the perimeter.
Follow the mower and press the
STOP’ button when the desired
distance has been reached.
Set zone: A
Press GO
Set zone: A
Press GO
Scroll DOWN once to
‘Learn edge’ option
Scroll to the zone of which
you want to learn the edge
distance and press ‘GO
Press ‘GO’ to start
the learning process
Work time
Press GO
Work time
Press GO
Work time
Press GO
Learn edge
Press GO
Learn edge
Press GO
Learn edge
Press GO
Learning edge
STOP to set
Learning edge
STOP to set
Learning edge
STOP to set
While driving around the perimeter.
Follow the mower and press the
STOP’ button when the desired
distance has been reached.
22
Figure 2.5
Rain sensor menu
Time and date
Press GO
Press ‘GO
Scroll UP/DOWN to set the
clock and the date and
press ‘GO’ for the next digit
00:00 dd/mm/yy
Next digit
10:37 23/04/07
Confirm
Press ‘GO’ to confirm
Time and date
Press GO
Time and date
Press GO
Press ‘GO
Scroll UP/DOWN to set the
clock and the date and
press ‘GO’ for the next digit
00:00 dd/mm/yy
Next digit
00:00 dd/mm/yy
Next digit
10:37 23/04/07
Confirm
10:37 23/04/07
Confirm
Press ‘GO’ to confirm
Figure 2.4
Time and date
Set sensitivity
Press GO
Rain sensor
Press GO
Reading (29) 25
Confirm
Rain sensor on
Press GO
Rain sensor off
Confirm
Set sensitivity
Press GO
Rain sensor
Press GO
Rain sensor
Press GO
Reading (29) 25
Confirm
Reading (29) 25
Confirm
Reading (29) 25
Confirm
Rain sensor on
Press GO
Rain sensor on
Press GO
Rain sensor off
Confirm
Rain sensor off
Confirm
2.2.3 Time And Date
Allows setting time and date (figure 2.4):
2.2.4 Rain Sensor
The Rain sensor feature enables the mower to detect rain and skip or stop the operation as it is
detected. There are two options under the
‘Rain sensor’ menu, as shown in Figure 2.5:
Set sensitivity – Enables to set the sensitivity of the rain sensor in which the mower will detect rain below
the threshold set. The default sensitivity set in the factory is 25, it means that in any reading below 25
the mower will detect rain and will not operate. The number in the brackets shows the actual reading of
the rain sensor.
Rain sensor on/off - Allows turning the rain sensor feature off to enable operation in rain and wet grass
conditions.
2.2.5 Language
Allows the user the option of viewing the LCD text in several different language versions.
2.2.6 ECO Mode
The ECO (Economic) mode feature enables operating Robomow using minimum energy required to
cut the grass and maintain the lawn. The ECO mode default is set to 'off'. Operation in ECO mode
reduces Robomow noise level during operation and allows longer operation time. It is recommended
to use the ECO mode only in zones with Base Station, where mowing is more frequent and a shorter
part of the grass is cut. If Robomow detects high grass it will automatically increase the power of the
mowing motor to enable cutting higher grass
.
2.2.7 Signal Type
In some circumstances there may be interference to the wire signal caused by other wire signal
activated in adjacent lawn (neighbor that use robotic lawnmower) or by any other appliance using
similar frequency. In case of signal interference, you may see one of the following symptoms (usually
close to the neighbor lawn):
a. Robomow is widely swinging when driving along the wire;
b. Robomow changes direction without reaching the wire;
c. Robomow crosses the wire outside the designated area;
d. 'Start inside' message is displayed although Robomow is inside the designated area and the
perimeter wire is connected in the right polarity;
If your mower faced one of the above symptoms, to change the signal type call to service.
Eco mode
Press GO
Eco mode off
Press GO
Eco mode on
Confirm
off on
23
Operation
Press GO
Total time
253h47m
First operation
Date: 13/03/08
Operation
Press GO
Operation
Press GO
Operation
Press GO
Total time
253h47m
Total time
253h47m
Total time
253h47m
First operation
Date: 13/03/08
First operation
Date: 13/03/08
First operation
Date: 13/03/08
Figure 2.6
Operation menu
Battery
Press GO
Battery voltage
12.8 25.5 12.7
Last run times
Press GO
1) 2h34m 25.8V
25/05/08
2) 2h32m 25.7V
24/05/08
10) 2h27m 25.7V
18/05/08
Battery
Press GO
Battery
Press GO
Battery
Press GO
Battery voltage
12.8 25.5 12.7
Last run times
Press GO
Last run times
Press GO
Last run times
Press GO
1) 2h34m 25.8V
25/05/08
2) 2h32m 25.7V
24/05/08
10) 2h27m 25.7V
18/05/08
1) 2h34m 25.8V
25/05/08
2) 2h32m 25.7V
24/05/08
10) 2h27m 25.7V
18/05/08
Figure 2.7
Battery menu
2.2.8 Blade Replaced
Choose this option after replacing the blade to restart the reminder counter. A reminder to replace the
blade again will be displayed after the next 200 hours of operation. Blade is easy to replace, refer to
section 5.5.
2.2.9 Wire Position
Allows user to test the wire position in ‘Edge’ mode while the mowing motors are switched off to prevent
any damage to the perimeter wire after the initial setup of the wire is completed.
2.2.10 Delay operation
This option allows the user to press GO but delay the operation starting time. It is useful when you want
to start the operation later in the day when the grass is dry and not early in the morning when the grass
is wet (and you have to leave for work).
To use this option, follow the steps below:
- Set the ‘Delay operation’ to X hours (choose between 1,2,3…or up to 8 hours);
- Switch on the Perimeter Switch (It is operated for 12 hours) and place the mower inside the lawn
towards the perimeter wire;
- Pressing ‘STOP’ then ‘GO’ (while holding the ‘STOP’ button) will change the display to ‘Press GO
again to skip edge’ and at the end of the warming up process, the mower will stay in place with a
message ‘Operation delayed – wait…’
- The mower will start the operation after X hours (as set in the ‘Delay operation’ menu) from the ‘GO
pressing.
2.3 Information
The ‘Information’ display (refer to figure 2.1) is used for information only, it allows the option to scroll
between the following menus:
2.3.1 Operation
Total time - Indicates the total number of hours the mower has been in operation.
First operation
– Indicates the date, in which the mower was first operated.
2.3.2 Battery
Battery voltage – Displays the current voltage of the batteries.
Last run times
– Indicates the last battery run time in the last 10 operations, the voltage at the beginning
of the operation and the operation date.
24
Temperatures
Press GO
Drive temp.
Press GO
Mow temp.
+24 C +75 F
Main board
+35 C +95 F
Left drive
+26 C +78 F
Right drive
+26 C +78 F
Temperatures
Press GO
Temperatures
Press GO
Temperatures
Press GO
Drive temp.
Press GO
Mow temp.
+24 C +75 F
Main board
+35 C +95 F
Left drive
+26 C +78 F
Right drive
+26 C +78 F
Figure 2.8
Temperatures menu
Figure 2.9
Configuration menu
Figure 2.10
Last stop causes menu
Configuration
Press GO
Main board
ESB5000E
Software
5.4v 21/10/07
Configuration
Press GO
Configuration
Press GO
Configuration
Press GO
Main board
ESB5000E
Software
5.2v 21/10/07
Configuration
Press GO
Configuration
Press GO
Configuration
Press GO
Main board
ESB5000E
Software
5.4v 21/10/07
Configuration
Press GO
Configuration
Press GO
Configuration
Press GO
Configuration
Press GO
Main board
ESB5000E
Software
5.2v 21/10/07
Last stop causes
Press GO
1) 11 [ 3]
10:35 25/05/08
2) 20 [ 2]
11:24 24/05/08
10) 7 [ 6]
10:58 19/04/08
Last stop causes
Press GO
Last stop causes
Press GO
Last stop causes
Press GO
1) 11 [ 3]
10:35 25/05/08
2) 20 [ 2]
11:24 24/05/08
10) 7 [ 6]
10:58 19/04/08
2.3.3 Temperatures
Displays the temperatures on the drive motors, mowing motor and on the Main Board.
2.3.4 Configuration
Displays the configuration of the Robomow: Main Board part number, software version and Base
Station Board part number (figure 2.9):
2.3.5 Last stop causes
Displays the last ten stop causes number and the date of the stop.
25
Chapter 3 – Operation and Charging
3.1 Edge Mowing
The first mowing chore for Robomow is mowing the edge. Edge is the outer perimeter of the active zone
Robomow is working within. This is essential where you placed your perimeter wire in the wire set-up.
Edge mowing provides a clean even cut around the perimeter and helps to minimize the amount of trimming
along walls and other obstacles.
Edge Operation
- Place Robomow inside the lawn, switch on the Perimeter Switch on and press the ‘GO’ button once;
- Robomow will automatically find the edge (perimeter). It will now begin mowing the edge, completing one to
two complete passes around the perimeter and then turn into the lawn to mow the inner area of the lawn;
- It will then drive into the lawn and begin what is called the scanning process (see paragraph 3.2).
3.2 Scanning (Mowing of the inner area)
The scanning process is simply a process whereby Robomow is moving across your lawn while it is mowing.
Robomow’s movement pattern is irregular with combination of parallel lines in narrow passes. Keep in mind
that the Robomow will not mow all the grass on its first pass; in fact it will leave uncut grass in between many
of the passes it makes. This is expected and is entirely normal. These uncut areas will be cut on subsequent
passes of the Robomow across the lawn. Just like a dishwasher, wait until the job is finished before you can
appreciate the results.
Robomow will continue to run for the amount of time selected or for the default
‘MAX’ time, which is
generally 2.5 hours, depending on grass type and condition.
3.3 Skipping Edge Mowing
Robomow provides a means that will allow you to skip the edge mowing process and start directly with the
scanning (mowing) process. In order to do this, simply press the
‘GO’ button twice at the initial startup of the
mower. Pressing
‘GO’ the second time immediately following the first press will tell the mower to skip
mowing the edge.
3.4 Operation
Robomow cannot operate unless the Perimeter Switch is turned on. Press the on/off button to turn on the
switch. To verify switch operation, there is a green LED located next to the button that will flash when
operating properly. If an intermittent beeping is heard shortly after turning the switch on, there is a problem
of cut wire or poor wire splicing (refer to chapter 4 – Text messages and Troubleshooting for further help).
Look to see which of the red LED is flashing to identify the problem (refer to figure 1.19). You must correct
the problem before Robomow can operate automatically.
Place the mower inside the active perimeter.
Press the ‘Down’ scroll arrow to receive the display of the zone to be mowed (Zone A or B) and press the
‘GO’ button. In a case where you have forgotten to turn on the Perimeter Switch, a ‘No wire signal’
message will be displayed, reminding you to turn the switch on.
3.5 Completing the Operation
When Robomow has operated the allotted time, it will simply stop in the lawn, waiting for you to drive it
back to the Base Station. The LCD will display a ‘
Recharge battery’ message if the mowing time is set to
MAX’ or ‘Time completed’ if the mowing time has been set to any time other than ‘MAX’.
If Robomow has completed its mowing and it is more than 15 minutes before you arrive to move it, the
LCD screen will be blank. Robomow will shut itself down into a sleep mode after 15 minutes of inactivity
at all times. This is an energy saving feature. Pressing the
‘GO’ button will wake it up and display the
message that was on the LCD when it went into sleep mode.
26
Figure 3.1
Power Supply connection
to charging adaptor
Figure 3.2
Charging adaptor
connection to Robomow
3.6 Charging
Of all the areas regarding the Robomow, proper charging of the Power Pack is second only to safety in
importance. Failure to follow the charging guidelines will result in poor performance and a short batteries
life
. After the completion of any daily cutting session it is very important to bring Robomow to its storage area
and plug it into the Power Supply as soon as possible.
The standard Power Supply is actually an indoor power supply. The charging system and batteries are
designed such that they can remain plugged in at all times of non-use without concern to overcharging, over
heating or damaging the batteries. In fact, it is the preferred way to maintain your batteries, always keep it
plugged into the Power Supply between uses. The power supply will re-charge the batteries from the
‘Recharge Battery’ level in approximately 16 hours, depending on conditions.
Connect the Indoor Power Supply to a regular household receptacle, 230 volts mains power and the output
lead of the Power Supply into the charging adaptor, Figure 3.1, and the charging adaptor to Robomow,
Figure 3.2, and the charging process will begin.
Important! The Power Supply is for ‘INDOOR USE ONLY’, place it in a sheltered place, dry location, which
is well ventilated and not exposed to direct sunlight.
The LCD will display ‘Charging’ and the battery icon will continually move from empty to full to show the
charging. Once the batteries are fully charged, the message will change to ‘Ready – keep charging’,
reminding you to keep it connected to the Power Supply until the next use.
Charging is such an important aspect for assuring good performance and batteries life that a special alert
and power management system is incorporated into the mower to remind and alert you when proper
charging process is not occurring.
Off-season storage
During winter or long period without using Robomow it is required to keep it connected to the Power Supply
in charging, preferably at room temperature.
WARNING!
Shock hazard. Injury or electrocution can occur. Robomow Power Supply
is designed for indoor use in dry locations only. Never use the Power
Supply or charge Robomow in areas where extreme dampness or wet
contact is likely. Never use a Power Supply when the leads are damaged.
Use only the recommended Power Supply with your Robomow.
27
Chapter 4 - Text Messages and Troubleshooting
4.1 Messaging
Robomow is equipped with an LCD panel that will notify you in the form of a text message when common
operational faults occur to instruct the user to perform a certain function or action.
If the LCD screen is blank, pressing the ‘
GO’ button one time will wake the mower up and the last fault or
message displayed prior to stopping will now be displayed. If a specific problem re-occurs, it is recommended to
identify the fault code prior to calling for service. Pressing the
‘UP’ arrow once, while the message is displayed,
is a shortcut button to display the
Last stop cause’ (refer to paragraph 2.3.5).
Message
Displayed
Probable Cause/Event Corrective/User Action
Adjust wire
then press GO
- Robomow detects an obstacle along the
edge while operated in ‘Wire position test
mode.
- Adjust the wire in the place where it
collides in the obstacle or remove the
obstacle and then press ‘GO’ to
continue in the wire position test.
Alarm will be
soon activated
- The ‘Theft guard’ system is activated, but the
4 digits code was not entered; the mower will
start the alarm soon.
- Enter the correct 4-digits code.
Bumper pressed
- Bumper is constantly being pressed
- Move mower away from object pressing
against bumper.
Change wires in
plot connector
- This message appeared at the first time the
GO’ button is pressed after completing the
setup in case the perimeter wire is
connected to the plot connector in the wrong
polarity.
- Change between the two wires ends
that connected to the plot connector
(the green connector that connected to
the Base Station).
Charging failure
- The charging process is not active - Contact service provider
Check mow height
- Mowing motor has faced over-current for too
long because of high grass or some obstacle
is stuck or wrapped around the blade.
- Something is preventing a blade from
rotating freely. Severe grass accumulation
under the mowing deck; rope or similar
object wrapped around mowing blade.
- Object jammed under mower preventing
blade from rotating.
CAUTION
– Remove fuse before lifting
the mower.
- Inspect blades for foreign material or
debris preventing rotation.
- Clean out accumulated grass clippings
using a wooden stick.
- Power supply is not plugged properly into the
main power supply
- The charging process has stopped due to a
temporary power loss.
- Confirm power supply is plugged into
the main power receptacle.
- No power to receptacle or main power is
shut off
- Turn power on to the main receptacle.
- Check the mains supply using another
appliance
Check power
- The Power Supply plug and its socket
contacts are dirty
- Clean the contacts with a brush or
piece of cloth
Check signal
Press GO
- There is no fitting between the 'Signal type'
setting in the menu and the signal jumper on
the Perimeter Switch;
- Robomow detects signal interferences from
adjacent activated lawn or from other
appliance activated near the zone;
- Set the 'Signal type' menu to 'A' and
confirm the signal jumper is installed on
the Perimeter Switch board; or
alternatively set it to 'B' and remove the
signal jumper from the board;
- In case of signal interference call the
service for help;
Close cover
- The bumper cover is not in its place because
one of the following reasons:
1.The cover has popped out during
operation while Robomow has collided in
obstacle.
2.The bumper cover was not placed properly
by the user in its place.
1. In case of short / slanted obstacles, it
must be protected from the
Robomow using the perimeter wire
around it.
2. Press the bumper cover downwards
and confirm it is clicked well.
28
Message
Displayed
Probable Cause/Event Corrective/User Action
Cross wire
- The perimeter wire is too close to the edge
- The lawn slope is too big
- Robomow does not succeed to turn in place
at the edge and it causes the mower to slip
out of the area.
- Cutting height too low for the lawn and grass
conditions.
- Move the wire towards the inner side of
the lawn and do not include area with
slopes that are too big.
- Fill any holes and pits in the ground.
- Increase the cutting height
- The drive motors have been working under a
severe load for too long.
- There is no need to do anything
Robomow will renew automatically the
operation, as the drive motor will cool
down.
Drive overheat
cooling, wait…
Short-circuit detected in Drive Motors. Contact your Service Dealer.
Enter code - The theft guard system is activated
- Enter the correct 4-digit code. ‘Theft
Guard’ can be deactivated under
Settings’. Contact your service provider
for assistance in a lost code situation.
Failure: xyz
- Internal failure
- Press ‘go’ to confirm the message; if
the message is still displayed, remove
the battery fuse for 10 seconds and
retry to operate the mower. If the
message still displayed, contact your
service dealer.
CAUTION – Remove battery fuse before
lifting the mower
- The Robomow has driven onto an
obstacle, raising the front end. Remove
or exclude this object from the mowing
area.
- The Robomow is being used on a slope
too steep for safe mowing. Exclude this
from the mowing area.
- High grass is preventing the front wheel
from fully riding on the ground. Raise
the cutting height.
Frnt wheel prob
- The Front Wheel has left the ground for
more than 8 – 10 seconds.
- The ground contains large holes or
indentions where the front wheel can
drop into when passing across. Fill
these areas with dirt and level off.
High temperature
waiting…
- Robomow is charged and the ambience
temperature is out of range (above 158ºF /
70ºC);
- Do not do anything, the charging is
stopped and Robomow is waiting for
temperature to change back to the
allowed range; if temperature stays out
of the range for more than 12 hours, the
message is changed to ‘High temp.
Press GO’.
Insert fuse
for charging
- Robomow is connected to charging without a
battery fuse
- Disconnect Robomow from charging,
insert the battery fuse and reconnect to
charging.
Keep charging
if not used
- Message is displayed every time the power
supply is disconnected.
- Displayed when the mower isn’t in operation
and not connected to the charging for a long
time.
- Press any key to change the display
back.
- Send the mower back to the Base
Station for charging / connect the power
supply or continue in operation.
Key pressed
- One of the operating panel buttons is
constantly pressed.
- Press GO’ to confirm the message and
to continue in operation. The message
is displayed to inform the user about
the problem, but will not prevent the
operation.
29
Message
Displayed
Probable Cause/Event Corrective/User Action
Keys locked - Child lock feature has been activated
- Press the Up
arrow key and then
press the ‘STOP’ button.
Child lock can be deactivated under the
Settings’ menu.
Low temperature
waiting…
- Robomow is charged and the ambience
temperature is out of range (below 32ºF /
0ºC);
- Do not do anything, the charging is
stopped and Robomow is waiting for
temperature to change back to the
allowed range; if temperature stays out
of the range for more than 12 hours, the
message is changed to ‘Low temp.
Press GO’.
Mow overheat
cooling, wait…
- The mowing motor has been working under
a severe load for too long of a time.
- There is no need to do anything –
Robomow will renew automatically the
operation, as the mowing motor will
cool down.
No wire signal
- Perimeter Switch is not turned on or not
connected to the zone intended to mow.
- The perimeter wire is not connected to the
Perimeter Switch
- The perimeter wire is cut
- Make sure the Perimeter Switch is
connected to the mains supply
- Disconnect the power supply from the
mains power and reconnect after 10
seconds.
- Check the Perimeter Switch is
connected to the correct zone and is
turned on.
- Check the connection of the perimeter
wire to the Perimeter Switch.
- Check for cut in the perimeter wire.
Rain detected
GO to ignore
- Robomow detects rain upon GO pressing
(received when pressing the GO button)
- Do not operate Robomow in rainy
weather and wet grass; If you choose to
override, press the ‘GO’ button; The
overriding is valid for the current
operation only
Rain detected
Press GO
- Robomow has skipped the last depart due to
rain detection
- It is not recommended to cut wet or
damp grass, but if you choose to
override the rain sensor, change the
setting of the ‘Rain sensor’ to ‘off’ under
the ‘Settings’ menu.
Rain sensor
disconnected
- Disconnection in the rain sensor wires.
- Press ‘GO’ to confirm the message and
call service for repair.
Ready
keep charging
- The battery is fully charged
- Keep the charger (power supply)
connected and operating
Recharge battery
- The maximum operating time has been
reached
- Connect the charger to the mower
Remove fuse
before lifting
- Robomow was lifted while the battery fuse is
connected.
- Remove the fuse before lifting
Robomow.
Remove fuse then
check blade
- Some obstacle is stuck or wrapped around
the blade.
- Something is preventing a blade from
rotating freely. Severe grass accumulation
under the mowing deck; rope or similar
object wrapped around mowing blade.
- Object jammed under mower preventing
blade from rotating.
- CAUTION – Remove battery fuse
before lifting the mower.
- Inspect blades for foreign material or
debris preventing rotation.
- Clean out accumulated grass clippings
using a wooden stick.
Replace blade
every 200 hours
- An automatic reminder to replace the blade
is displayed every 200 hours
- Replace the blades and restart the
counter of the blades replacement
reminder by choosing the ‘Blades
replaced – Clear reminder option
under the ‘Settings’ menu
30
Message
Displayed
Probable Cause/Event Corrective/User Action
- An unknown fault has occurred and user
help is required
- Manually drive/carry the mower away
from this particular area and restart
operation.
Start elsewhere
- Drive wheel motors have been working
under a severe load during automatic or
manual operation.
- Check to insure the mower is not stuck,
allowing the drive wheels to slip.
- Check the ground for holes or
indentions, where the mower has
stopped and fill it with dirt and level off.
- Check the drive wheels are free to
rotate and nothing block them.
- Remove the mower away from this
particular point and restart operation.
Start inside
- Automatic operation is initiated while
Robomow is placed out of the perimeter wire
lope.
- Place the mower inside the lawn and
press the ‘GO’ button.
- Robomow get stuck in place with no succeed
to continue driving.
- Check the ground for holes or
indentions, where the mower has
stopped and fill it with dirt and level off
– especially in the area close to the
perimeter, where the Robomow turns in
place.
Stuck in place
- Robomow has slipped out of the perimeter
wire lope because of slopping area or wet
grass.
- Robomow has difficulty to turn in place
because the front wheel has fallen into hole
or indention and it caused the mower to turn
in place without detecting wire or bumper.
- Confirm the area is not too sloppy and
make sure to work in dry condition.
- Check the perimeter wire is not too
close to the edge – remove if required.
- Conform the mowing deck is not set too
low.
- There is an option to drive back to the
lawn in reverse before Robomow
perform the turn in place (contact your
service dealer for details).
Switch off
before lifting
- The user carries Robomow manually while
the main switch button is on.
- Switch off the main switch button before
carrying Robomow.
Time and date
- Displayed every time the batteries fuse is
taken out of the mower (reset operation)
- Set real time clock (day and hour) and
the date.
Time completed
- The operating time set for that zone has
been reached.
- Connect to the charger if all mowing has
been completed for the day.
Waiting for
signal…
- Robomow has stopped the operation,
because there is no signal detected.
- Check the power to the Base Station.
- There is electrical power interruption.
There is no need to do anything –
Robomow will renew automatically the
operation if the power will come back
within an hour from the break; if the
power will come back after more than
one hour, Robomow will drive back to
the Base Station for charging, but will
not renew the operation and mowing.
31
4.2 Other Operational or Fault Problems
Problem
Encountered
Probable Cause/Event Corrective/User Action
- Wire disconnected from perimeter
switch or from the Base Station.
- Confirm wire is plugged in and wire leads
are firmly attached.
- Perimeter wire cut
- Walk along perimeter, including islands and
look for obvious cuts or breaks in the wire.
Repair with Robomow wire splice
connectors.
'Cut wire’ indicator
flashing on
Perimeter Switch
or
the Base Station
beeps continuously
for 'Cut wire’
- Poor connections
- Check and repair all loose/poor or corroded
connections.
- Twisted cables, or a screw terminal,
insulated with insulation tape is not a
satisfactory splice. Soil moisture
causes the conductors to oxidize and
after a while result in broken circuit.
- Use the connectors supplied in the box. It is
waterproof and gives a reliable electrical
connection.
‘Poor connection’
indicator flashing on
Perimeter Switch
or
the Base Station
beeps intermittently
for poor wire
splicing or too long
wire
- Perimeter wire too long for one zone
- A maximum perimeter wire length of 500 m
is recommended. Areas requiring longer
lengths should be broken into separate
zones.
Robomow doesn’t
complete the edge
- Peculiar geometry of the perimeter - Perform ‘Learn edge (refer to 2.1.2.2)
- Mower is in deep sleep.
- If not connected to the Base Station/charger
at all times when not in use, the Robomow
will conserve power by entering into a deep
sleep mode. Press the main switch button
(on/off) 3 seconds continuously
to wake
Robomow or remove the fuse for 3
seconds.
Robomow will not
operate and nothing
will display on the
LCD screen.
- Batteries have been discharged from
lack of charge maintenance.
- It is required for the charger to remain
connected to Robomow when not in use.
Failure to do so can cause permanent
damage to the batteries. Contact your
service provider.
The Robomow is
noisy and vibrates
- Damaged or unbalanced blade
- Check the lawn is free from branches,
stones or other objects that can damage the
blade before operating the Robomow.
- Replace the blade
- Grass is too high in relation to the set
cutting height
- It is recommended to cut not more than a
1/3 of the green part of the grass.
- Set the cutting height to a higher position
- Use Robomow more frequently to maintain
your lawn.
- Grass is wet
- For best cut, operate Robomow when the
grass is dry. It is recommended to mow
grass early afternoon.
- Dull blade - Replace blade.
- Robomow works too few operations - Use the Robomow more often per week
Poor quality of
mowing (grass
clippings are left on
the lawn)
or
Uneven mowing
results
- Working area is too large - Limit the working area
32
Problem
Encountered
Probable Cause/Event Corrective/User Action
LCD display is in a
foreign language.
- The language setting was changed or
not correctly set.
- Place the mower out of the Base Station
and follow the sequence listed;
- Press ‘STOP’ button few times to confirm it
is on the main display
- Press ‘UP’ button twice
- Press ‘GO’ button once
- Press ‘Down’ arrow button once
- Press ‘GO’ button once
- Press ‘Down’ arrow button 4 times
- Press ‘GO’ button once
- Using the arrow, scroll to the correct
language
- Press ‘GO’ to confirm this selection
- Important! It is possible to see the last 10 battery run times and the battery voltage at
the beginning of the operation in the ‘Information’ menu (refer to paragraph 2.3.2)
- Battery is not fully charged at the
beginning of the operation
- Confirm the battery icon is fully and not
changed (while charging in the Base
Station) or ‘Ready keep charging’ message
is displayed (while charging through power
supply) prior the operation.
- ‘Work Time ‘ for that zone is set to
specific time and not to ‘MAX’
-Work time’ can be changed under ‘Zones
setup’ menu
- Grass is extremely over grown or very
wet.
- Raise cutting height.
- Always mow the grass frequently enough to
prevent over growth.
- CAUTION – Remove battery fuse before
lifting the mower
- Inspect blades for foreign material or debris
preventing rotation.
- Clean out accumulated grass clippings
using a wooden stick.
Short run time,
operates less time
than normal
- Batteries are reaching a normal end of
life state.
- Replace batteries.
- Confirm that the time in the mower is
set correctly (hour and date)
- Set the time (See paragraph 2.2.3)
Robomow operates
at the wrong times
- The GO’ button was pressed with no
meaning, by someone or by a pet
(‘Last stop cause’ under the
Information’ menu should be 805).
- To prevent unintended operation you can
activate the ‘Child guard’ or the ‘Anti theft’
options, which requires pressing of few
buttons in order to start the operation.
- Wire disconnected from perimeter
switch or from the Base Station.
- Confirm wire is plugged in and wire leads
are firmly attached.
- Perimeter wire cut
- Walk along perimeter, including islands and
look for obvious cuts or breaks in the wire.
Repair with Robomow wire splice
connectors.
'Cut wire’ indicator
flashing on
Perimeter Switch
or
the Base Station
beeps continuously
for 'Cut wire’
- Poor connections
- Check and repair all loose/poor or corroded
connections.
33
Before any cleaning
is done remove the
batteries fuse.
Caution
Serious injury can occur.
Always remove batteries fuse
before any maintenance or
cleaning is done or before lifting
Robomow. Blade is very sharp
and can cause severe cuts or
lacerations. Always wear heavy
work gloves when working with
and around the blade.
WARNING!
Chapter 5 - Maintenance and Storage
5.1 Recommended Maintenance Schedule
Maintenance
Service Interval
Maintenance Procedure
Regularly
Remove the batteries fuse and check any damage on the blade.
Check and remove grass clippings and dirt from the mowing deck if necessary,
particularly when mowing wet and damp grass (refer to section 5.2)
Charge the Robomow batteries after every use.
150 – 200 Hours
Replace the blade; replace it more frequently if the edges dull in rough or sandy
conditions (see Figure 5.1).
Remember to restart the automatic blade replacement reminder whenever the
blade has been replaced (refer to section 2.2.6).
5.2 Cleaning
Robomow
Use only a damp cloth and a dry brush to clean the outer surfaces.
A light detergent can be used in a water solution, and then soaking and
wringing dry the cloth for cleaning. Never use harsh or abrasive cleaning
solutions. Never spray with a garden hose or other type of liquid spray hose.
Mowing Deck
The underside of the mowing deck needs to be inspected, and cleaned if necessary, between operations.
The Robomow is a dedicated mulching mower and may accumulate clippings under the mowing deck,
particularly when mowing wet and damp grass.
Most grass accumulation can be removed using a small wooden stick or similar object. Carefully scrape the
collected grass debris from under the mowing deck. If necessary, remove the blade to gain better access to
the mowing chamber in order to clean it. Do not place the mower upside down, damage to the bumper can
occur. Instead, lean it against another surface to gain access to the mowing deck area.
NEVER use a water hose or other type of liquid sprayer to clean the underside of the mower. Component
damage can occur. Use only a damp or wet cloth to wipe the surface clean after scraping.
5.3 Battery
The batteries are maintenance-free, but have a limited life span of 1-3 years. Battery life depends on the
number of operations per week and the length of the season. The batteries should only be replaced by a
service dealer.
Important! Do not place used batteries in your household trash. Batteries must be collected, recycled, or
disposed of in an environmentally sound manner. Return the old batteries to an approved sealed lead (acid)
battery recycler.
34
Figure 5.1
Blade replacement
11
22
33
Blade replacement instructions
Caution! To prevent the risk of serious injury,
always remove the battery fuse when
replacing the blade.
For your safety, always wear heavy
work gloves when working with or
around the cutting blade.
1. Remove the battery fuse;
2. Wear heavy work gloves;
3. Place Robomow on its rear side
vertically, lay against a wall or turn it
upside down on a soft surface;
4. To remove blade, using both hands,
squeeze the plastic lock tabs at the
base of the blade (step 1);
Squeeze the plastic locks tabs in the
arrow direction as shown in step 2.
5. Then pull blade assembly off, away
from mower (step 3);
6. Holding the replacement blade by its
base, push until it is locked into place.
You will hear a click when it locks.
If you do not hear a click, remove
blade, and repeat the procedure.
5.4 Replacing the Blade
The blade replacement is a very easy operation to
perform; follow the instructions in figure 5.1 below.
The cutting blade of the Robomow should be
examined for damage between operations. Only use
sharp blade.
Replace blade at least once per season or after 200 hours of operation, the first to come. It is recommended
to replace the blade for best performance. Machine sharpening is not recommended, as a good balance
cannot be achieved after machine sharpening.
Robomow has an automatic reminder to replace the blade after every 200 hours of operation.
’Replace
blade – every 200 hours’ message appears and pressing the ‘GO’ button will clear the message and
enables the operation of Robomow.
Whenever replacing the blade, it is recommended to restart the counter of the blade replacement reminder
by choosing the
‘Blade replaced’ option under the ‘Settings’ menu and pressing the ‘GO’ button again to
clear the reminder.
35
Wire
Connector
1
2
3
Wire
Connector
11
22
33
Figure 5.2
Wires splicing
1. Strip one cm (0.5 inch) of
each wire ends together
and twist the stripped ends
together using pliers.
2. Insert the twisted wires into
the splicing connector.
3. Screw the wire connector
on the twisted wires; make
sure is tight.
Figure 5.3
Charging
5.5 Splicing the Perimeter Wire
If the perimeter wire needs to be spliced: Use the connectors supplied in the box, as shown in figure 5.2. It is
waterproof and gives a reliable electrical connection.
IMPORTANT INFORMATION!
Twisted cables, or a screw terminal, insulated with insulation tape is not a satisfactory splice. Soil
moisture will cause the conductors to oxidize and after a while result in broken circuit.
5.6 Winter Storage
Robomow
Remove the battery fuse and clean the Robomow (refer to sections 5.2). Store Robomow indoors in a clean
a dry place, standing on its wheels; confirm the area around the bumper is free.
Insert the battery fuse and connect the power Supply to the mains supply (figure 5.3)
for the entire period
in which Robomow will not be operating; confirm ‘Charging’ is displayed and ‘Ready – keep charging’
when the battery is fully charged.
The charging system and battery are designed such that they can remain plugged in at all times of non-use
without concern to over charging, over heating or damaging the battery.
Perimeter Switch
It is recommended to remove the
Perimeter Switch for the winter period:
- Disconnect the power supply from the mains power;
- Open the Perimeter Switch cover;
- Disconnect all connectors from the board;
- Remove the Perimeter Switch and place it in dry storage;
- Disconnect the green plot connector (keep it connected on the board for the next season) from the
perimeter wire ends and protect it from moisture to prevent corrosion of the wires while not connected to
the Perimeter Switch; You may place the Friendly Robotics wire nut connector onto both wire ends for
protection in the winter.
36
5.7 Batteries Replacement
WARNING!
Follow the instructions below. Complete replacement of one battery before starting to replace the second
battery.
Replacing the batteries:
- Lift the bumper and remove the batteries fuse;
- Remove the cutting height adjustment knob by lifting it
upwards (figure 5.4)
- Unscrew the five nuts manually at the rear side of the Chassis
cover (figure 5.5). If you find it difficult use a wide flat
screwdriver;
- Lift the rear side of the cover (see figure 5.6) and disconnect
only the two cables from the left battery (figure 5.7);
Place the new battery and connect the cables to the battery
tabs when the red and the black cables are fitted to the color
on the battery;
- Disconnect the cables from the right battery;
- Place the new battery and slightly crimp the battery
connectors with plyers, so that they fit tightly on the battery
tabs.
- Connect the cables to the battery tabs respectively by color;
- Place the cover back in its position and screw the five nuts
manually, confirm they are tight enough;
- Insert the batteries fuse and confirm the Robomow wakes up.
Figure 5.4
Figure 5.5
Figure 5.6
Figure 5.7
37
Theft Guard Code
Fill in the four-digit code you have
selected for the Theft Guard
system as a safe record in the
event you forget the code
selected.
____ ____ ____ ____
Robomow Serial Number
________________________
Chapter 6 - Specifications
Dimensions
64cm (25 inches) Length x 52cm (20 inches) Width x 30cm (12 inches) Height
Weight
17.6kg (38.8 lb)
Noise Level
Measured sound level: 77.2 dB
Guaranteed sound level: 80 dB
Mowing System
Cuts 1cm (0.4in) outside the wheels
Mowing width - 20cm (8 inches)
Cutting height – 20-80mm (0.8-3.2 inches)
Blade motor RPM – 5800
Year of Manufacture
The decal below is found on the left side of the mower's base.
The first 2 digits represent the year of manufacture.
i.e. the label above belongs to a Robomow which was produced in 2007.
PRD5201A RL072502RM
IRL0725020001
RM200
38
Chapter 7 - Accessories
Perimeter Switch
Convenience of having a switch for each
zone and not moving one switch from
zone to zone. (operated by electricity).
Peg Pack (50)
For larger lawns and additional zones.
Perimeter Wire
For larger lawns and additional zones.
Blade
Keep a spare blade on hand. Sharp
blade is important for safety and good
cutting performance.
Wire connector
Used for repairing or splicing wires (as
needed
)
.
Plot connector
Used for connecting the completed
perimeter wire set-up to the perimeter
switch
Remote Control
for convenient transport of Robomow
between plots, as well as mowing very
narrow areas manually
.
Batteries Pack for RM Perimeter Switch
Preferable for areas where electricity is
not available or not close enough to the
Perimeter Switch.
2 x 12 AH Batteries
Weak batteries? No need to send
Robomow to your service provider.
They can easily be replaced by the
user.
39
Tips for maintaining your lawn
Robomow
®
- Lawn care has never been so easy
Best time to mow
Mow your lawn when the grass is dry. This prevents the clippings from clumping and leaving piles on the lawn.
Mow it late in the day rather than during the heat of the day.
Mowing frequency
Mow often, producing short, small clippings. During the active growing season the mowing frequency should be
increased to once every 3-5 days, before the grass is too long. Short clippings decompose quickly and will not
cover the grass surface. If the grass gets too high, raise the cutting height, mow, then gradually lower it over
several mowings.
Cutting Height
Follow the "1/3 rule:" mow no more than 1/3 of the length of the grass. Proper
mowing will produce short clippings that will not cover up the grass surface. You may
have to cut the lawn more frequently, or double cut, when the lawn is growing fast,
such as in the spring.
Water
Grasscycling reduces the amount of water needed by lawns since the clippings are about 80 - 85% water.
Grasscycling slows evaporation losses from the soil surface, and conserves water. Most lawns need less water
when Grasscycling.
Watering
Water your lawn between 4 a.m. and 8 a.m. in the morning, so water has time to soak into the soil before the
heat of the sun causes evaporation.
Your lawn needs 1 to 1-1/2" (3-4cm) of water weekly. Deep watering allows grass to develop a deep root
system, enabling the lawn to resist disease and drought.
Do not over water
Too much water is not only wasteful but can also increase turf growth, which requires more frequent mowing.
Let the soil partially dry out between watering. Water when the top two inches of soil have dried out. Use an
object such as a screwdriver to probe your soil and measure the depth of the moisture.
Fertilization
Grasscycling reduces the amount of lawn fertilizer needed because the clippings provide about 1/4 of a
lawn's annual needs.
Blade
Keep your mower blade sharp. Sharp blade provides a clean, safe and efficient cut. Dull mower blade will tear
and shred the tips of the grass, which can provide an entry point for disease organisms and weaken the grass
plant. It is recommended to replace Robomow blade once a year.
Thatch
Clippings and thatch are simply not connected. As mentioned previously, grass clippings are approximately 80-
85 percent water with only small amounts of lignin, and decompose rapidly.
When we stop and think about it, golf courses, sports fields, and parks have been mowing grass for years and
recycling with no grass catchers.
A small amount of thatch (approximately 1/2 inch) is actually beneficial to a lawn. Grass clippings
protect your lawn's root system from heat and water loss.
40
RM/City Series Limited Warranty
Friendly Robotics warrants to the original purchaser that the RM/City series ‘Product’ is free from defects in materials and
workmanship when used under normal residential* purposes for a period of 24 months, 12 months for the batteries,
beginning from the date of purchase. Product accessories, including replacement parts are warranted for a period of 6
months from the date of purchase. This warranty provides for the cost of parts and labor to repair covered defects when
performed by an authorized Friendly Robotics service and warranty facility. A valid proof of purchase is required for warranty
repairs.
The limited warranty does not cover transportation costs of any kind. The owner bears all responsibility for
transportation costs to an authorized Friendly Robotics service and warranty facility.
*Normal residential purposes are defined as use of the product on the same lot as your primary home. Use at more than one
location is considered commercial use, and this warranty would not apply.
Items and Conditions Not Covered
This express warranty does not cover the following:
Cost of regular maintenance service parts or procedures, such as blade or blade sharpening.
Any product or part that has been altered, misused, abused or requires replacement or repair due to accidents or
lack of proper maintenance.
Normal wear and tear, including fading of paint or plastic parts.
Cost of installation or reinstallation, removal of installation or any costs or damages associated with improper
installation or use of product.
Any product that has been opened, repaired, modified or altered by anyone other than a Friendly Robotics
authorized repair facility.
Repairs necessary due to improper battery care (all models) and/or improper charging process such as charging in
wet conditions (RM200/City100), electrical supply irregularities, or failure to properly prepare the mower or battery
prior to any period of non-use.
Repairs necessary due to water damage, other than incidental rain exposure, repairs due to lighting or other acts of
God.
Instructions for Obtaining Warranty Service
Should you feel your Friendly Robotics product contains a defect in materials or workmanship, contact the retailer who sold
you the product.
Owner Responsibilities
You must maintain and care for your Friendly Robotics product by following the maintenance and care procedures described
in the owner/operator manual. Routine maintenance, whether performed by a service provider or by you, is at your expense.
General Conditions
Repair by an authorized Friendly Robotics service and warranty repair facility is your sole remedy under this warranty. There
is no other express or implied warranty. All implied warranties of merchantability and fitness for use are limited to the
duration of this express warranty. Friendly Robotics is not liable for indirect, incidental or consequential damages in
connection with the use of the Friendly Robotics Product covered by this warranty, including any cost or expense of
providing substitute equipment or service during reasonable periods of malfunction or non-use pending completion of repairs
under this warranty. Some states do not allow exclusions of incidental or consequential damages, or limitations on how long
an implied warranty lasts, so the above exclusion and limitations may not apply to you. This warranty gives you specific legal
rights, and you may also have other rights, which vary from state to state.
Alwa
y
s follow the safet
y
instructions s
p
ecified in this Manual
41
EU Declaration of Conformity
Manufacturer: F. Robotics Acquisitions Ltd.
Hatzabar St., Industrial Zone
P.O.Box 1412 Pardesiya,
42815 Israel
The products covered by this Declaration
24 Volt Battery operated Automatic Lawn Mower model RM200 (with Perimeter Switch)
24 Volt Battery operated Automatic Lawn Mower model RM510 (with Base Station)
F. Robotics Acquisitions Ltd. declares under sole responsibility that the products identified above conforms with the
protection requirements of the EMC directive and with the principal elements of the safety objectives of the Low Voltage
Equipment directive, and that the following standards have been applied:
- EMC
-
Robomow (Tested according to EN 55014-1:2006 & EN 55014-2:1997 + A1:2001)
- Base Station (Tested according to: EN 55024:98 + A1:2001 + A2:2003 & EN 55022:1998 + A1:2000+A2:2003)
- Electrical Safety
BS EN 60335-1:2002 *AMD1 15172, 2002 *AMD2 15626, 2005 *AMD4 15051,
2004 *AMD5 15536, 2005 *AMD6 16671, 2007
BS EN 50338: 2006 AMD1 16778, 2006
- Machinery Directive
Directive 2006/42/EC
Safety of Machinery - Risk Assessment ISO 14121-1/2
- Noise Directive
- To BS EN ISO 3744: 1995 and *ISO 11094: 1991. With reference to Outdoor noise directive 2000/14/EC:
Amended by directive 2005/88/EC and the corrigenda table 1. Article 12: Test code of Annex III Part B Item 32.
Sound level
Measured sound power level: LwA =77.2dB
Guaranteed sound power level: LwA =80dB
- EMF
BS EN 50366: 2003 amd1 16426, 2006
EMC Competent Body All Others Directives Competent Body
QualiTech
30,Hasivim Street
P.O. Box 3083
Petah Tikva 49130
Israel
SGS UNITED KINGDOM LIMITED
Rossmore Business Park
ELLESMERE PORT
CH65 3EN South Wirral Cheshire
United Kingdom
The technical documentation kept by Mr. Dedy Gur, QA director.
Address: Hatzabar St., Industrial Zone P.O.Box 1412 Pardesiya, 42815 Israel. And Mr. Lennert Van der Pols Friendly
Robotics BV. Address: Expeditieweg 4-6 Andelst 6673 DV, Nethelands.
I hereby declare that the above product conforms to the requirements as specified above.
Shai Abramson – Senior VP R&D
F. Robotics Acquisitions Ltd.
1 October 2011
42
EC DECLARATION OF CONFORMITY*
)
(Noise Level)
F. Robotics Acquisition Ltd. hereby certifies that equipment described below
0.1. Type: 24 Volt Battery operated Automatic Lawn Mower
0.2.
Make (Trade name): ROBOMOW
0.2.1.
Model/Type: RM200 (with Perimeter Switch)
RM510 (with Base Station)
0.3.
Manufactured by: Name: F. Robotics Acquisitions Ltd.
Address: Hatzabar St., Industrial Zone P.O.Box 1412 Pardesiya, 42815 Israel
0.4. Person who keeps the technical documentation:
Name: Mr. Dedy Gur, QA director.
Address: Hatzabar St., Industrial Zone P.O.Box 1412 Pardesiya, 42815 Israel
0.5 Notified body:
SGS UNITED KINGDOM LIMITED
Rossmore Business Park ELLESMERE PORT
CH65 3EN South Wirral Cheshire United Kingdom
SGS Reference: ELS111832/4/R/SW/07
0.6 Conformity assessment procedure (Test Specification):
To BS EN ISO 3744: 1995 and *ISO 11094: 1991.
With reference to Outdoor noise directive 2000/14/EC: Amended by directive 2005/88/EC and the
corrigenda table 1. Article 12: Test code of Annex III Part B Item 32.
0.7 Date:6
th
May 2008 0.8 Place: SGS UNITED KINGDOM LIMITED
Conforms to the requirements of Directive 2000/14/EC and to the requirements of the Directives
2005/88/EC and the corrigenda table 1. Article 12: Test code of Annex III Part B Item 32:
Machinery Directive
Low Voltage Directive
Directive on Electromagnetic Compatibility
Signature (Full name and position
**
): Shai Abramson – Senior VP R&D
Brief description of equipment: 24 Volt Battery operated Automatic Lawn Mower
1. Sound level
1.2. Measured sound power level:……………………...LwA =77.2 dB
1.3. Guaranteed sound power level:…………………….LwA =80 dB
2. Sound related parameter:
Cutting Width: 19.5 cm
*)
This
declaration must be made in the same language as the original instructions, and either typewritten or printed. A translation
in the language (s) of the user country must also be provided. These translations are subject to the same conditions as the
original instructions.
**)
e.g. a function empowering the signatory to sign on behalf of the manufacturer (if the manufacturer is a natural person, this is
the manufacturer or his legal representative, and in the case of a legal person or association having no legal personality, it is the
person authorized to represent/manage him by law or by his rules or articles of association).
***)
For combustion-engine driven equipment it should be the nominal engine speed at which noise measurements are recorded. For chain saws: this should
be the nominal engine speed under full load conditions at which noise measurements are recorded.
43
44
To register your product online, go to
http://robomow.com/register
www.robomow.eu / www.robomow.com
18

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Robomow RM200 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Robomow RM200 in de taal/talen: Engels als bijlage per email.

De handleiding is 2,33 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

Andere handleiding(en) van Robomow RM200

Robomow RM200 Gebruiksaanwijzing - Nederlands - 44 pagina's

Robomow RM200 Gebruiksaanwijzing - Deutsch - 44 pagina's

Robomow RM200 Gebruiksaanwijzing - Français - 61 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info