664046
49
Verklein
Vergroot
Pagina terug
1/58
Pagina verder
48
Problem
Encountered
Probable Cause/Event Correcve Acons
Mower does not
dock properly
and sometimes
misses the Base
Station contacts
- Height differences between the lawn and
the Base Station surface.
- FillsomegroundtoattenthelawntotheBase
Station to allow smooth entrance.
- The wire underneath the Base Station is
not tight and placed in the middle of the
Station.
- ConrmthewireunderneaththeBaseStation
is straight, tight, and centered below the Base
Station.
- The Base Station is set up on a side
slope.
- Move the Base Station to a relatively level
ground.
- The Base Station is placed too close to
the corner of the lawn
- Move the Base Station so it is not within 3
meters after a corner.
Uneven mowing
results
- The time between operations is too long
because of long inactive time windows.
- Minimize the Inactive Time windows to allow
Robomow to complete the Mowing Cycle faster
and to achieve even mowing results.
- Grass is growing very fast.
- If it is during a fast growing season – change
the Mowing Frequency (refer to Section 6.4.2 –
P001).
- The shape of the lawn is complicated
(Narrow Passages, obstacle and islands).
- In a complicated lawn more time is required for
the mower to achieve better mowing results.
- Increase the mowing hours percentage (refer to
Section 6.4.1.2).
- The set area is smaller than the actual
lawn size.
- Increase the zone area (refer to Section 6.4.1.4)
Robomow
operates during
Inactive Time.
- Wrong clock time is set in the mower.
- Verify that the time on the mower is set correctly.
- Set the time (refer to Section 6.4.1.1).
- Reset the Inactive Time (refer to Section
6.4.1.3).
Robomow
operates during
rain
- Rain Sensor is disabled or its sensitivity
is set too low
- Enable the Rain Sensor and adjust its sensitivity
if required (refer to Section 6.4.2 – P007/p008)
- The Islands feature is set to On. In this
case the mower is searching for the base
by moving around the lawn. This special
search method takes more time, and
may create an impression that the mower
is still mowing, while in fact it is already
searching for the Base Station.
- No special action is required. For more
information about the Islands On/Off feature
refer to Section 6.4.2 – P002)
Cut wire indicator
isashingon
Power Box
- The Extension Cable is disconnected or
damaged between Power Box and the
Base Station.
- ConrmtheExtensionCableispluggedinand
wireleadsarermlyattached.
- Perimeter Wire is cut.
- Walk along Perimeter Wire.
- Look for cuts or breaks in the wire.
- Repair with Robomow wire splice connectors.
- Scan the code and
watch the video
demonstrating the
Corrective Actions of
the “Perimeter Wire
is cut”.
The poor
connection
indicator is
ashingon
Power Box
- Poor connections
- Check and repair all loose, poor, or corroded
connections.
- Twisted cables or a screw terminal which
is insulated with insulation tape is not a
satisfactory splice.
- Soil moisture causes the conductors to
oxidize.
- Use the connectors supplied in the box. They
are waterproof and give a reliable electrical
connection.
49

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Robomow RC312u bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Robomow RC312u in de taal/talen: Engels als bijlage per email.

De handleiding is 3,43 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Robomow RC312u

Robomow RC312u Gebruiksaanwijzing - Nederlands - 58 pagina's

Robomow RC312u Gebruiksaanwijzing - Deutsch - 58 pagina's

Robomow RC312u Snelstart handleiding - English - 4 pagina's

Robomow RC312u Gebruiksaanwijzing - Français - 58 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info