625559
40
Verklein
Vergroot
Pagina terug
1/46
Pagina verder
NX SERIES V0913 39
English
Planer protection during mortising (g. 33)
Warning:
Always put the planer protection bridge in position above the planer arbour. This prevents accidental
contact of the operator’s hands with the planer arbor and knives during mortising. Alternatively, slide
the planer fence fully forward (covering the planer arbor with the planer fence rear protection).
Fig.33
Fixing the mortising chuck to the spindle (g. 34)
Always ensure that both the spindle and chuck threads absolutely clean before assembly.
Fig.34
Warning: the mortiser chuck has a left hand thread!
Put the chuck onto the spindle arbor up to the end and check if the V-groove (2) in the spindle matches
with the 2 holes in the chuck (if not, the spindle thread will be damaged!). Introduce the 2 Allen screws
(1) and tighten them well. These press screws are needed to prevent the chuck from loosening.
Maintenance (g. 35, 36, 37)
Warning: always disconnect the machine from its power supply before starting any maintenance
work!!!!
The interior and exterior parts of the machine must be cleared at regular intervals to avoid
accumulation of dust and woodchips. Any deposits of resin on the cross cut table sliding bars or on
any other moving part of the machine must be removed with a piece of cloth and a little solvent (petrol,
kerosene or other product). Never smoke or have any naked ame near the machine when using
inammable products, this to prevent risk of re and serious burns for the operator.
All bearings are double sealed and lubricated for life, therefore they need no maintenance. All columns,
e.g. spindle, thicknesser, mortiser need to be lubricated once a month, especially when the machine
is used in a very humid environment. The best product to use is simple penetrating oil in a spray can.
All other moving parts have to be kept free of dust and woodchips and may be greased with the same
penetrating oil.
The use of a dust extraction system will most certainly extend the life of your machine. The life of the
motors can be extended by blowing out saw dust from the cooling fan and from the motor body itself.
1
40

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Robland NXTZ bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Robland NXTZ in de taal/talen: Engels als bijlage per email.

De handleiding is 1,93 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Robland NXTZ

Robland NXTZ Gebruiksaanwijzing - Nederlands - 100 pagina's

Robland NXTZ Gebruiksaanwijzing - Deutsch - 100 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info