625559
32
Verklein
Vergroot
Pagina terug
1/46
Pagina verder
NX SERIES V0913 31
English
Spindle
Mounting the tools on the spindle (fig.18)
1 Set the brake release switch of the selector switch on in order to free the brake and turn the
spindle free by hand and set the Allen key on the countersunk Allen bolt on top of the spindle
arbor (1)
2 Push the locking lever (2) to the right and, at the same time, manually turn the spindle arbor (3)
until the lower locking pin locks into the hole in the spindle.
3 Now loosen the clamp screw on top of the arbor with the Allen Key.
4 Always mount the spindle as low as possible on the arbor, so the bearing isn’t overloaded.
5 Mount the correct number of spindle rings and tighten the screw, on top of the arbor.
6 When the lever (2) is released, the locking of the spindle arbour is automatically disengaged.
7 Always lock the position of the spindle height by locking the handle (3) behind the handwheel.
Fig.18
Adjusting the spindle height (g. 18)
1 Unlock the locking lever (3) by turning it to the left.
2 The spindle arbour can be raised or lowered using the hand wheel (4).
3 After height adjustment always secure the spindle arbour by locking the lever (3) by turning it to
the right.
Remark: When, after intensive use of the locking lever (3), it is no longer possible to lock this lever, take
off the nut and remove the lever. Then turn it 1/6 turn to the right before putting it back on again. Put the
nut back on and tighten it.
The spindle fence
Working with the spindle fence (fig. 19)
The spindle fence is tted onto the table with two locking knobs (1). The body of the spindle fence is
equipped with two slots which enables front and back movement. When the fence is tted onto the table,
the position of the aluminium fence plates can be adjusted by means of the adjustment knob (2). The
opening of the 2 fence plates goes like follows: loosen the wing nut (3) which hold the fence and move
the fence towards each other, so there is a minimal gap between the protruding tool and the fence plates.
It is advisable to use a false fence or integrated fence which is mounted between the 2 spindle fences.
The adjustment of the fences can be checked with a at and precise rule.
Before starting the machine, the blocking of the bars of the fences on the table has to be checked. The
wood pushers exert vertical and horizontal pressure on the work piece, which pushes the work piece
against the table and the fence and which makes it slide easily. The manual wood pusher (g. 20),
supplied with the machine, can be used to push the wood safely. Not one element is xed on the useful
table surface. The 10 mm space between the base of the horizontal wood pusher and the table makes it
possible to move the wood pusher under the wood pushers. To replace the spindle tool, or to make use
of the feeder, the whole pusher system can be cleared by ipping it over to the back of the spindle fence:
Pull the lever in the direction of the arrow. Lift up a little the cover plate. Now the system can be ipped
over to the back. This part will prevent the fences from falling down. It is advisable to use a Q1
1
2
3
4
32

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Robland NXTZ bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Robland NXTZ in de taal/talen: Engels als bijlage per email.

De handleiding is 1,93 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Robland NXTZ

Robland NXTZ Gebruiksaanwijzing - Nederlands - 100 pagina's

Robland NXTZ Gebruiksaanwijzing - Deutsch - 100 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info