625559
28
Verklein
Vergroot
Pagina terug
1/46
Pagina verder
NX SERIES V0913 27
English
Sliding table (g. 11)
The machine is delivered with the sliding table mounted onto it. For a good adjustment and functioning
of the sliding table, it is necessary that the machine is evenly placed in both directions by means of a
level. All adjustments and adaptations of the sliding table have been made by the factory.
To create a smooth movement of the wood or the panel, the sliding table is set at +/- 0.2 mm above de
cast iron saw table.
The sliding table can be locked in one position along the whole length. This is necessary when, for
example, sawing lengthways with the parallel fence.
The bolt is situated on the side of the sliding table (g. 11.1). Pull the bolt forward and click it in the
opening at the side of the sliding table. To unlock it, pull the bolt backwards and turn it 180°. Two
rubber stops on the lower beam of the sliding table stop the course of the sliding table. When multiple
movements back and forwards are repeated, it is possible that the ball bearing moves slightly. This will
cause some resistance when pushing the sliding table.
This can also occur if the total course of the sliding table is shortened. With a few short pushes, with
the purpose of reaching the end of the course, the position of the ball bearing can be improved.
Fig.11
Attention: cleaning and maintenance of the sliding table
It is essential to frequently blow away the accumulated shavings and dust, between the two
parts of the sliding table and the ball bearing. Push the sliding table to the end of the course
to get better access to the rails, the ball bearing and the slides of the sliding table. Repeat
this, with the sliding table moved to the other side, to be sure all shavings and dust is gone.
A normal lubricant such as WD-40 is sufficient to grease the slides of the sliding table and to
obtain good functioning.
ADJUSTMENT OF THE SLIDING TABLE (g. 12)
The alignment between the sliding table can be adjusted by means of the 2 adjustment points below
the fixed beam of the sliding table. Loosen the 2 screws (2) that hold the fixed beam on the chassis
of the machine. Loosen the 2 bolts (1) and align by moving the sliding table. After the adjustments,
tighten the 2 bolts. The adjustment of the sliding table against the cast iron saw table is made by
means of the 2 bolts (1).
1
28

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Robland NXTZ bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Robland NXTZ in de taal/talen: Engels als bijlage per email.

De handleiding is 1,93 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Robland NXTZ

Robland NXTZ Gebruiksaanwijzing - Nederlands - 100 pagina's

Robland NXTZ Gebruiksaanwijzing - Deutsch - 100 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info