747912
6
Verklein
Vergroot
Pagina terug
1/38
Pagina verder
6
Trim levers (all) - Used to shift the neutral or center position of each servo as labeled in the diagram. Once either trim lever
is operated, the trim position is displayed on the LCD screen. Also once either edit key is operated, all trim positions are
displayed sequentially on the LCD screen.
NOTE: The throttle trim lever is intended for fine tuning the throttle servo when the engine is at idle. Throttle trim does not
affect the throttle servo when the throttle control stick is all the way up (so idle r.p.m. can be adjusted without affecting
throttle settings through the rest of the stick movement).
Charging jack - Port for charging the transmitter batteries with the included battery charger.
On/off switch
DATA INPUT lever - Used to change the values of the various functions displayed on the LCD screen
Liquid – crystal display screen (LCD) - Displays programming modes and values entered.
MODE key - Used to scroll through and display the “11-14” different functions.
SELECT key - Used to display the values for the current function.
Throttle – cut button - To use the throttle-cut function, lower the throttle stick all the way, then push the throttle-cut button to
fully close the carburetor and shut off the engine.
Throttle/rudder control stick - Operates the servos connected to channel 3 (throttle) and channel 4 (rudder) in the receiver.
A:Trainer switch - Operates the trainer functions. To operate as a trainer switch the transmitter must be connected to another
transmitter via. a trainer cord (available separately).
H:Idle – up switch - This switch operates to change the fight condition which sets the throttle curve and pitch curve of mid
air maneuvers (rolls, loops, stall turns) and 3D flight.
A:Retractable landing gear switch/Channel 5 - Switch operates the servo connected to channel 5 in the receiver. If your
model has retractable landing gear, this is the control used to extend and retract the gear.
H:Gyro switch/Channel 5 - You can connect the sense adjust connector to channel 5 of the receiver to operate the gyro,
which has two different senses. Also if you use the Futaba GY401/502/611 Gyro, two different gyro sense settings on the gyro
function in this transmitter can be called by this switch.
Antenna - Radiates signals to the receiver. NEVER point at the model when flying! See page 9 for detail.
Changing the Throttle Stick Ratchet System to Helicopter-touch
1. Open the battery cover on the back of the transmitter and remove the transmitter battery.
2. Remove the four transmitter rear case screws and remove the rear case.
3. Change the ratchet plate on the gimbal section to the smooth ratchet plate for helicopter use.
Ratchet plate
for airplane
Ratchet plate
for helicopter
(The above photos show a Mode 2 system as supplied. )
6

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Robbe Futaba T6EX bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Robbe Futaba T6EX in de taal/talen: Engels als bijlage per email.

De handleiding is 2,28 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info