467096
22
Verklein
Vergroot
Pagina terug
1/128
Pagina verder
22
<Before Use>
Warning
Connecting connectors
Be sure to insert the connector until it stops at
the deepest point.
How to protect the receiver from vibration and
water
Wrap the receiver with something soft such
as foam rubber to avoid vibration. If there is
a chance of getting wet, put the receiver in a
waterproof bag or balloon to avoid water.
Receiver's antenna
Never cut the receiver's antenna. Do not bind
the receiver's antenna with the cables for
servos.
Locate the receiver's antenna as far as possible
from metals or carbon fiber components such
as frames, cables, etc.
*Cutting or binding the receiver's antenna will reduce the ra-
dio reception sensitivity and range, and may cause a crash.
ƔUse rubber band to stretch
antenna and then fix it.
ƔUse a rubber bushing to the position where
antenna is coming out from the airframe so
that the antenna won't be cut due to the
friction.
ƔUse rubber band to stretch antenna and then
fix it.Make a knot inside of the airframe so that
the antenna will not fall out.
Antenna
Antenna-exiting
hole
Rubber grommet or
silicon tube, etc.
Antenna
Nonmetal tube
*Use rubber grommet or
silicon tube to protect
from cut or peel off
insulation of antenna on
the fuselage antenna-
exiting hole.
*Place the receiver
antenna out from the
fuselage part to the
nonmetal tube installed
in skid etc. Please keep
antenna away from
parts that made of metal
and carbon graphite.
Servos throw
$GMXVW\RXUV\VWHPVRWKDWSXVKURGVZLOOQRW
bind or sag when operating the servos to the
full extent.
*If excessive force is continuously applied to a servo, your
aircraft may crash because the servo would be damaged
and the battery would be consumed rapidly.
Mounting servos
Use a vibration-proof rubber (such as rubber
grommet) under a servo when mounting the
servo on a servo mount. And be sure that the
servo cases do not touch directly to the metal
parts such as servo mount.
*If a servo case is contacting directly to the airframe, the
vibration of the airframe directly travels to and may dam-
age the servo.
Rubber
grommet
Brass eyelet
Wood screw
Servo mount
2.3-2.6mm nut
washer
Rubber
grommet
Brass eyelet
Servo mount
2.3-2.6mm screw
(Helicopter)(Airplane/Glider)
Servo lead wires
To prevent the servo lead wires from being
EURNHQE\YLEUDWLRQGXULQJÀLJKWSURYLGHDPDUJLQ
so that the wire sticks out slightly and fasten it at
suitable points. In addition, periodically check the
wire during daily maintenance
Fasten about 5-10cm
from the servo outlet
so that the lead wire
is neat.
Margin in the lead wire.
Mounting the power switch
When mounting a power switch to an airframe,
make a rectangular hole that is a little larger than
the total stroke of the switch so that you can turn
the switch ON/OFF without binding.
Avoid mounting the switch where it can be
covered by engine oil and dust. In general, it is
recommended to mount the power switch on the
VLGHRIWKHIXVHODJHWKDWLVRSSRVLWHWKHPXIÀHU
Safety precautions when you install receiver and servos
22

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Robbe Futaba T-12 FG bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Robbe Futaba T-12 FG in de taal/talen: Engels als bijlage per email.

De handleiding is 1,8 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Robbe Futaba T-12 FG

Robbe Futaba T-12 FG Gebruiksaanwijzing - Nederlands - 80 pagina's

Robbe Futaba T-12 FG Gebruiksaanwijzing - Deutsch - 78 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info