Handleiding Ritter Markant 05 (pagina 14 van 61) (Nederlands, Duits, Engels, Frans, Italiaans, Spaans, Pools, Noors)

544564

Verklein

Vergroot

Pagina terug

1/61

Pagina verder

Unfold the illustrations at the front

and back of this manual.

Please read these instructions

thoroughly before you start to use

the appliance. Keep these operat-

ing instructions in a safe place

and ensure that they are included

with the appliance if passing it on

to a third party.

INTENDED USE

The multi slicer is used to slice

household foods.

If the appliance is used for a

purpose other than this, or if it is

operated incorrectly, severe inju-

ries may occur or the appliance

may be damaged. All warranty

and liability claims will be ren-

dered null and void in this case.

BEFORE USING THE

APPLIANCE FOR THE

FIRST TIME

Preparation

Remove the appliance carefully

from the packaging. Remove all

packaging parts and keep these

together with the packaging in a

safe place. Clean the appli-

ance before allowing it to come

into contact with any food (see

CLEANING).

Setting up the appliance

• Set the appliance down on a

at, non-skid surface close to a

mains socket.

On the positioning plate (6)

remove the left-over holder (8),

the nger protection (7a) and the

slide unit (7b) one after the other

by pulling them out and up.

Mounting the slice car-

riage (7): Insert the nger protec-

tion into the slot in the base of

the carriage and fasten it in place

by sliding it in the direction of the

arrow.

Unwind the mains cable (11)

to the length required from the

cable compartment (4) under the

appliance. In doing so, fasten the

mains cable in the slot provided

for it on the base of the appliance.

Swivel the positioning plate

fully downwards into the working

position.

Place the slice carriage's

guide runner onto the positioning

plate's lateral guide groove at an

incline. Swivel the slice carriage

downwards in the direction of

the positioning plate. The slice

carriage's guide runner must be

fully mounted onto the positioning

plate's guide groove.

Slide the left-over holder (8)

onto the nger protection (7a).

• Plug the cable into the socket.

SLICING

Use the slice thickness adjust-

ment knob (2) to set the required

thickness.

Place the food to be sliced

onto the slice carriage (7). Use

the left-over holder (8) to press it

up against the stop plate (3).

Protect your hands, by always

using the slice carriage and,

where applicable, the left-over

holder. Exception: Excessively

large foods to be sliced.

Turn the appliance on using

the switch (1). Two operating

modes are available:

Temporary operation: Press the

switch and slide it towards the

arrow until you feel some resist-

ance. The rotary blade (10) runs

as long as the switch is pressed

and held down in this position.

Continuous operation: Press

the switch and slide it towards

the arrow beyond the resistance

point until it latches into place.

The rotary blade runs without the

switch having to be pressed and

held down, until you push the

switch back into the "0" position.

Note:

Never use the appliance for more

than a maximum of 5 minutes in

continuous operation.

For markant model

Adapt the slicing speed using the

variable adjuster (12) to suit the

food to be sliced. When slicing

soft food, set a low slicing speed.

Set a higher speed for hard food.

• With the appliance running,

gently feed the food to be sliced

into the path of the rotary blade.

• When nished slicing, wait until

the rotary blade has come to a

complete stop.

• After each use, turn the slice

thickness adjustment knob to the

"0" position, in order to cover up

the sharp rotating blade and to

avoid any injuries.

CLEANING

Caution:

Switch the appliance off before

cleaning it; pull the mains plug

out of the socket and turn the

slice thickness adjustment

knob (2) to the "0" position.

Clean the multi slicer regularly

to prevent the accumulation of

food residue. The rotary blade

must also be cleaned regularly

as described below to prevent its

surface from rusting.

Note:

Over time, an accumulation of

food residue may cause damage

to the surface of the rotary blade,

causing it to rust.

Preparation

• Remove the left-over holder (8)

and the slice carriage (7).

Removing the rotary blade:

Open the blade catch (9), by

turning it in a clockwise direction.

Take hold of the rotary blade

at its rotational centre and

remove it.

Cleaning after each use

• Wipe down the housing and

all removed parts, including the

rotary blade, with a damp cloth.

English

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

lees eerst de handleiding door;
controleer of uw vraag al eerder door iemand anders is gesteld;
probeer uw vraag zo duidelijk mogelijk te stellen;
heeft u een probleem en al geprobeerd om dit op te lossen, vermeld dit erbij aub;
heeft u een oplossing gekregen van een bezoeker dan horen wij dat graag in dit forum;
wilt u een reactie geven op een vraag of antwoord, gebruik dan niet dit formulier maar klik op de knop 'reageer op deze vraag';
uw vraag wordt direct op de website gezet; vermijd daarom persoonlijke gegevens in te vullen;

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Ritter Markant 05 Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info