805760
13
Verklein
Vergroot
Pagina terug
1/36
Pagina verder
13
Installation & Commissioning
General installation
Pipe ttings
All pipe connections to the Remeha Flexistor are made via BSP female parallel threaded pipe
connection directly to the unit.
Cold water supply
A 2”cold water supply is recommended, however, if a smaller supply exists which provides
su󰀩cient ow this may be used. More ow noise may be experienced from small bore pipes due
to the increased water velocity through them. A minimum ow rate of 100l/min is required for the
Remeha Flexistor range of cylinders
High ow cold water control pack (Low and high pressure)
The control pack consists of a Pressure Reducing Valve with integral strainer, check valve, core
unit and expansion relief valve. The pressure settings are adjustable for the low or high pressure
valve sets. For the“low” pressure valve set the pressure reducing valve can be set between 1.5
and 6 bar. For the “high” pressure valve set the pressure can be set between 5 and 10 bar. For
optimum performance the following installation instructions should be complied with.
Note: The expansion vessel pressure must be set in accordance with the inlet pressure set on the
pressure reducing valve by the installer. Set the Expansion Vessel pressure before pressurising
the cylinder.
Installation
Flush supply pipe work before connection to remove all ux and debris prior to tting the inlet
controls. Failure to do this may result in irreparable damage to the controls and will invalidate the
warranty.
The pressure reducing valve can be tted in any orientation to suit the installation as long as it is
tted in the correct ow direction. Check the ow arrows on the side of the body.
The expansion relief valve should be installed with the discharge pipe work in either the horizontal
position or facing downwards, if the discharge pipe is facing upwards debris may be deposited on
the seat of the valve when in operation.
The blank plastic plugs in the body of the pressure relief valve are pressure gauge connections to
enable pressure monitoring to be carried out, should the system develop a fault. It is recommended
that these be accessible (the pressure reducing valve has two – only one need be accessible).
Expansion relief discharge pipe work must be connected to a safe visible discharge point via a
tundish and the pipe work must have a continuous fall. If site conditions allow, the expansion relief
discharge pipe work can be connected to the T&P valve discharge pipe work before the tundish.
Pressure Reducing Valve
The Pressure Reducing Valve can be connected anywhere on the cold water mains supply prior
to the Remeha Flexistor unit. There is no requirement to site it close to the unit, it can be located
at a point where the mains supply enters the premises if this is more convenient but you must
install a non-return valve just after the reducing valve for ease of maintenance. The pressure
reducing valve incorporates a adjustable pressure reducer / strainer. The valve can be tted in
any orientation to suit the installation, however, ensure that the valve is installed with the direction
of ow arrows (stamped on the side of the brass body) pointing towards the Remeha Flexistor
cylinder
PRV WARNING:
IF THERE IS AN UPSTREAM CHECK VALVE OR FITTING WHICH MAY PREVENT BACK FLOW
THEN HIGH PRESSURES CAN BE EXPERIENCED DUE TO AMBIENT TEMPERATURES
WHICH CAN CAUSE DAMAGE TO THE VALVES AND FITTINGS
13

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Remeha Flexistor bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Remeha Flexistor in de taal/talen: Engels als bijlage per email.

De handleiding is 2.7 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info