805754
33
Verklein
Vergroot
Pagina terug
1/44
Pagina verder
1. Install a flow switch to make sure that there is sufficient flow before
you start the heat pump.
2. Install a fitting for filling and rinsing in the heating circuit.
3. Fill the buffer, if applicable.
4. Fill the heating circuit.
5. When filling the heating circuit, leave time for accumulated air to
escape the system.
6. Close the filling and draining valve.
7. If the heat pumps are installed in a location higher than the heating
system, install proper air bleed devices, preferably in the return line to
the heat pump. This prevents a lack of flow due to air in the
installation.
7 Commissioning
7.1 Check list before commissioning
Check if all the following steps are done before commissioning the device:
The heating circuit is flushed, filled and deaerated.
A free flow of water in the system is guaranteed.
The condensation drainage is installed.
The compressor is connected with a right rotating field.
The fans are rotating in the correct direction (pushing air into the
machine).
The space near the air inlet and air outlet is free.
The settings of the flow switches are adjusted properly to the device.
All electrical connection cables are connected and protected.
All screws are tightened.
The heating system is protected against freezing.
The main switch is set to ON.
The earth conductor resistance and the isolation resistance should be
tested for compliance with local rules and regulations. The tests must be
repeated according to the intervals applicable on site or according to the
local rules and regulations about commissioning and recommissioning.
Use a PE conductor of at least 10 mm2 cross section.
7.2 Commissioning procedure
7.2.1 Bleeding the system
The hydraulic system must be pressurized to 2 bar, and importantly: there
must be no air in the system. Before operating the heat pump, fill the
hydraulic system to the appropriate pressure, and make sure all the air
has bled from the system. The heat pump is ready for use when the
system pressure is correct and all the air has escaped from the system.
8 Operation
8.1 Use of the controller
Use the controller to commission and operate the device. The controller
can be installed inside near the building switching board or near the heat
pump as long as it is weather protected.
To operate active cooling, see the manual of the controls.
7 Commissioning
7697291 - v.05 - 11032022 33
33

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Remeha E-HP AW 44 Cool Plus B bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Remeha E-HP AW 44 Cool Plus B in de taal/talen: Engels als bijlage per email.

De handleiding is 12.52 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info