659424

Redmond RMC-M90E Handleiding

10
Verklein
Vergroot
Pagina terug
1/200
Pagina verder
10
V. CLEANING AND GENERAL MAINTENANCE GUIDELINES
Before you start cleaning the device, make sure that it is unplugged and has cooled down. Use soft cloth and mild
soap to clean. We recommend cleaning the appliance after each use.
Prior to rst use or in order to remove the odor steam half a lemon for 15 minutes using “STEAM” program.
Do not use a sponge with hard or abrasive surface; solvent and abrasive cleaning methods (gasoline, acetone) are not
allowed. Do not immerse the device in water or wash it under running water.
Steam valve, inner aluminum lid, and the bowl need to be cleaned after each use. The bowl is dishwasher safe. By
the end of cleaning, wipe the bowl dry.
To clean the inner lid:
1. Open the lid.
2. Press 2 plastic holders on the inner side of the lid pointing towards the center until open.
3. Gently pull the inner lid towards yourself and down to get it separated from the main lid.
4. Wipe the surfaces of both lids with wet cloth or tissue. Wash under running water, using mild soap if needed.
Not dishwasher safe.
5. Carry out the assembly in return sequence: slide the inner lid into upper groves overlapping it with the main
lid. Gently push the holders until they click into place. Make sure that the inner lid ts tightly.
The steam valve is located on the top lid of the device and consists of two parts: the cover and the main part. To
clean the steam valve:
1. Take the cover of the steam valve off by pulling it gently up and towards yourself as shown A4.
2.
Inside the removed cover, turn the main part of the steam valve anticlockwise (in direction of <open>) to remove.
3.
Take the rubber sealing ring out; wash all parts of the steam valve following cleaning and general maintenance
guidelines provided.
CAUTION! Do not twist or stretch the rubber sealing ring to avoid its deformation.
4. Carry out the assembly of the steam valve in return sequence: place the rubber sealing ring back into the
holder; overlap the groves of the main part of the valve with the corresponding ledges on the inside of the
cover and turn the valve clockwise in direction of <close>. Install the steam valve back into the lid of the
device, with the extraction ledge facing the back.
Condensation may accumulate in the special cavity around the bowl and in condensation container at the back of
the device.
1. Open the device and take the bowl out. Lift the front side of the device if needed, to let the condensate ow
down into the container.
2. Pull container towards yourself to remove.
3. Pour condensate out. Rinse the container and put it back into place.
4. Remove condensate remaining in the cavity around the bowl using cloth or tissue.
VI. COOKING TIPS
This chapter familiarizes you with the practical tips and solutions to some common problems you may experience
when using the multicooker.
THE DISH IS UNDERCOOKED
Possible Causes Solving the Problem
The lid of the device was either open or was not closed properly.
• Try to avoid opening the lid while cooking.
• Close the lid until it clicks into place. Make sure that the rubber sealing ring
located on the inner side of the lid is not deformed or damaged in any way.
Cooking temperature was not observed because the bowl and the
heating element did not t tightly.
• There should not be any foreign objects between the lid and the hous-
ing of the device, remove if any.
• Always make sure that the heating element is clean and ts tightly with
the bowl before cooking.
• Wrong ingredients or settings were chosen.
• General proportions were not observed, the size of the in-
gredients was too large.
• Wrong time settings.
• Chosen recipe is not appropriate for the device.
•
We recommend using recipes adjusted for the device. Choose proven
recipes only.
• Set the time and cooking program, choose ingredients, proportions, and
the size of ingredients according to the recipe.
Steaming: the amount of water in the bowl is too little to provide
enough steam.
Use the amount of water recommended. If in doubt, check the water level
while steaming.
Frying:
Too much oil was added.
•
Frying ingredients add an amount of oil enough just to cover the bottom
of the bowl.
• Follow recommendations given in the recipe while deep frying.
Too much moisture inside the bowl.
Do not close the lid of the device while frying unless specied in the recipe.
Using frozen ingredients defrost and drain before frying.
Cooking: the water boiled away during preparation of foods with
high acidity.
Certain products need to be processed before cooking: washed, browned, etc.
Follow recommendations given in the recipe.
Baking (dough did
not bake through):
Too much dough in the bowl. Use a smaller amount of dough.
Proofed dough has reached the inner lid
and covered the steam valve.
• Take the baked product out of the unit, turn it over and place back. Bake
until ready.
• Next time use smaller amount of dough.
THE DISH IS OVERCOOKED
Possible Causes Solving the Problem
Wrong ingredients, wrong size of ingredients or time settings.
•
We recommend using the recipes adjusted for your model. Try
choosing proven recipes only.
• Set the time and cooking program, choose ingredients, propor-
tions, and the size of ingredients according to the recipe.
The dish remained in the unit with the “Keep Warm” on for too long after
it’s been cooked.
We recommend using the “Keep Warm” function moderately. If your
device features the function of disabling the “Keep Warm” in advance,
use it to avoid the problem.
LIQUID BOILS AWAY DURING COOKING
Possible Causes Solving the Problem
Milk boils away.
Depending on the quality of milk used, it may boil away. To avoid this,
we recommend using only ultra-pasteurized milk with the fat content
of 2.5% or less. Dilute milk with water if needed (p 7).
• Ingredients were not properly processed (washed poorly, etc.)
• Wrong general proportions or ingredients.
•
We recommend using the recipes adjusted for the device. Try
choosing proven recipes only. Set the time and cooking program,
choose ingredients, proportions, and the size of ingredients ac-
cording to the recipe.
•
Whole grains, meat, sh, and seafood need to be rinsed thor-
oughly before cooking.
THE DISH IS BURNT
Possible Causes Solving the Problem
• The bowl was not properly washed after last use.
• Non-stick coating is damaged.
Make sure that the bowl is clean and has no coating defects before
cooking.
General amount of ingredients is smaller than recommended. Use proven recipes, adjusted for the device.
Cooking time was too long.
Reduce the cooking time or follow recommendations given in the
recipe adjusted for your model.
Frying: oil was not added; the ingredients have not been stirred or turned
over.
Frying products add amount of oil enough just to cover the bottom of
the bowl. Stir ingredients thoroughly while frying or turn over as required.
Stewing: not enough liquid. Add more liquid. Avoid opening the lid while stewing.
Cooking: not enough liquid (proportions were not observed). Follow recommended ratio of liquids to solids while cooking.
Baking: the bowl was not greased before baking.
Grease the bottom and sides of the bowl with butter or oil before
baking (do not pour oil inside).
INGREDIENTS LOOSE THEIR SHAPE WHEN COOKED
Possible Causes Solving the Problem
Ingredients have been over stirred.
Frying foods, do not stir the ingredients more often than every 5–7
minutes.
Cooking time was too long.
Reduce cooking time or follow recommendations given in the recipe
adjusted for the device.
… 10 …

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Redmond RMC-M90E bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Redmond RMC-M90E in de taal/talen: Alle talen als bijlage per email.

De handleiding is 8,1 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info