597822
15
Verklein
Vergroot
Pagina terug
1/165
Pagina verder
Build 31 v31.6.16 Beta
© 2007-2011 RED.COM INC. JUNE 22, 2011
14 14
Where: A = camera A, 001 = reel 001, C002 = clip 002, and 0502 = May 02
And A6 is a two digit alphanumeric random number generated by the camera. This number helps avoid
duplicate file names if two cameras are inadvertently named A on the same set.
Three cameras identified as A, B and C can therefore have individually recognizable clips:
A001_C001_0502**.RDC B001_C001_0502**.RDC C001_C001_0502**.RDC
A single camera identified as A can have individually recognizable reel numbers, such as:
A001_C001_0502**.RDC A002_C001_0502**.RDC A003_C001_0502**.RDC
A single camera identified as A can have individually recognizable clip numbers, such as:
A001_C001_0502**.RDC A002_C002_0502**.RDC A003_C003_0502**.RDC
NOTE: Even if the same Reel number and / or camera name are reused, the use of the two random
characters generates non-duplicate file names, such as:
A001_C001_0502A6.RDC A001_C001_050267.RDC A001_C001_0502F8.RDC
Under normal operation, the reel number increments each time the camera formats a new piece of digital
media, up to a maximum value of 999. However the reel number may be manually reset at any time to
001or other desired value.
MASTER / SLAVE CAMERA CONFIGURATION
For complete information on clip naming conventions for recorded media from cameras in a master / slave
configuration, refer to APPENDIX E: MASTER / SLAVE CAMERA CONFIGURATION.
SMPTE TIMECODE
As each recording is made, the RED ONE camera records two independent timecode tracks.
Edge Code is a SMPTE timecode track that always starts at 1.00.00.00 on the first frame of each piece of
digital media. It is a sequential code that is continuous from frame to frame and also between clips. Edge
Code is equivalent to RUN RECORD as used on broadcast cameras.
Timecode is a SMPTE timecode track that syncs to the camera’s clock, or if operated in Jam Sync mode,
syncs to an externally supplied SMPTE master timecode signal. It is therefore a sequential code that is
continuous from frame to frame, but discontinuous between clips.
NOTE: Timecode and Edge Code are only output from the 5-pin timecode connector if OUTPUT is
enabled in the TIMECODE setup menu, but are always embedded in HD-SDI.
When in Varispeed or Time-lapse recording modes, the timecode counters are updated at the same frame
rate as the recording. This means valid SMPTE timecode is created without count jumps that would affect
clip playback or editing. If using an external timecode source with Jam Sync enabled, the clip’s master
time reference point is the first frame of the recorded clip.
When in Loop Record mode, the Edge Code will become discontinuous between clips, because frames
copied into the cache memory are discarded. This may lead to problems with applications that assume a
continuous timecode sequence. It is therefore recommended that Timecode be selected when operating
in this recording mode.
15

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Red One 31.6.16 - 2011 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Red One 31.6.16 - 2011 in de taal/talen: Engels als bijlage per email.

De handleiding is 12,63 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info