623533
21
Verklein
Vergroot
Pagina terug
1/28
Pagina verder
19
ArtNo.800-0126 - Fitting the sealing strip
This dishwasher is for use in GB and IE only. After sales service
applies to GB and IE only.
Positioning the Dishwasher

Do not install the dishwasher in a room where the
temperature is likely to fall below freezing (0 °C).

Do not grip the door when moving the dishwasher.
The dishwasher should be aligned to the front of the adjacent
cabinets, with allowance made for the door thickness. The
dishwasher has water supply and drain hoses that can be
positioned on either to the left or the right.
Before installing the dishwasher into a kitchen cabinet,
holes must not be drilled into the sides, or door, to avoid
compromising the performance and operation of the
dishwasher.
A plastic self-adhesive anti-condensation strip is supplied
with the dishwasher. Fix the strip to the underside of the
worktop, along the front edge (Fig.5-1).
Connect up the cold water supply, the drain hose and the
electrical connections (see below) then slide the dishwasher
into the cabinet opening.
Cold Water Connection
Connect the water supply hose (supplied loose) to the cold
water inlet at the rear. Connect the other end to a ¾“ BSP tap
connector (Fig.5-2). Make sure that the washers are in place
and that it is fastened securely in place.
IMPORTANT: If the water pipes are new or have not been
used for an extended period of time, run the water for
a while to make sure that the water is clear and free of
impurities BEFORE connecting to the dishwasher. Failure
to carry out this precaution may lead to the water inlet
becoming blocked and causing damage the dishwasher.
The water prssure should be between 0.03 Mpa and 1Mpa.
Pressures above 1Mpa will require a pressure relief valve to
be tted.
Drain Hose Connection
Connect the drain hose to the water outlet. Insert the hose
into a drainpipe with a minimum diameter of 40 mm, or let it
run into a sink, making sure to avoid bending or crimping. If
necessary, t a siphon trap (U-bend) with a connecting piece.
The free end of the hose must be at a height of between
50 -110 cm and must not be immersed in water (Fig.5-3).

WARNING! The connecting piece for the siphon trap
(U-bend) must be solidly fastened to the wall to
prevent the drain hose from moving and allowing
water to spill outside the drain (Fig.5-4).
ArtNo.800-0101 - Cold water connection
Washer
Water hose
¾“ BSP tap connector
110cm
50cm
Fig.5-1
Fig.5-2
Fig.5-3
Waste
hose
Waste hose support
(xed to wall)
To waste
Fig.5-4
5. Installation
• DocNo.800-0503 - Installation - RDW459 dishwasher
21

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Rangemaster RDW1045FI bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Rangemaster RDW1045FI in de taal/talen: Engels als bijlage per email.

De handleiding is 1,32 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info