500597
7
Verklein
Vergroot
Pagina terug
1/40
Pagina verder
7
Names
Description
Default setting & Other possibility
The following parameters are only visible if a water contact sensor (NTC 10K sensor) is connected and
installed on the incoming pipe of the manifolds, and if the parameter “HC” is on “SenS” position.
(See the schematic and system drawing to install the sensor)
Setting Level to switch your installation between Heat and
cool mode.
When the water temperature (Wtemp) on the incoming pipe
decrease below this setting (minus the hysteresis value/2),
the installation will work in cooling mode.
Wtemp < HCL HCh/2 => System in cooling mode
Wtemp > HCL + HCh /2 => System in heating mode
Press (OK) to view the instantaneous value measured by
the sensor.
Default: 22°C
Adjustable: 5 to 35°C
Hysteresis value for the setting level “HCL”, to avoid quick
commutations between Heat & Cool change.
Default: 5°C
Adjustable: 3 to 10°C
The following parameters are only visible if a water humidity sensor (NTC 10K sensor or free contact
sensor) is connected and installed on the incoming pipe of the manifolds
(See the schematic and system drawing to install the sensor)
Setting level to switch off the cooling function to avoid
residual humidity in the house:
When the water temperature in the pipe decrease under this
level during the time of the anti short cycle adjusted onrHt
the cooling function will be stopped.
Press (OK) to view the instantaneous value measured by
the sensor.
Default: 18°C
Adjustable: 5 to 25°C
Minimum time to decide to stop the cooling function when
the water temperature decreases under the “rHL” level.
Default: 5°C
Adjustable: 3 to 10°C
Delay time (in seconds) for the pump start up after the first
heat demand from minimum one zone.
This function is generally used to avoid noise and damage
of the hydraulic parts of the installation.
Default: 60 s
Adjustable: 0 to 240s
Press (OK) during 5 seconds to reset the installation.
All parameters are replaced by default value.
Press (OK) on this parameter to exit the parameters menu end come back to the main
display.
7. RF ALARM
- You could see the RF alarm on the Master (Red blinking LED on the concerned zone) and on the RF main
zone programmer (in the status line).
- If a RF alarm is detected on one zone, the regulation will be maintained on this zone by average of the actual
room temperatures of the other zones used on the Master.
- Check the thermostat batteries of the concerned zone. If batteries thermostat must be changed, always
replace the 2 batteries in the same time. The RF alarm message should be disappear alone when batteries will
be replaced.
Note:
If all zones are in RF alarm (Red blinking) check the RF antenna connection before replacing of all thermostat
batteries.
7

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Radson 51055 - SLAVE RF bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Radson 51055 - SLAVE RF in de taal/talen: Nederlands, Duits, Engels, Frans als bijlage per email.

De handleiding is 1,57 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info