726826
34
Verklein
Vergroot
Pagina terug
1/60
Pagina verder
6 Installation
6.1 Unit installation
Unit installation
NOTICE!
Installation and commissioning should only be
performed by trained specialists.
The unit is attached by means of a wall bracket,
with consideration to the minimum clearances
required.
1. Mark the mounting points on the structurally
permissible building sections according to the
dimensions of the wall bracket.
2. If necessary
, remove the break out opening
of the housing.
3. Connect the medium pipes, electrical cables
and condensate drainage line to the indoor
unit as described below
.
4. Hang the indoor unit onto the wall bracket by
tilting it back slightly and by pressing the
bottom part of the unit against the bracket.
5. Check again that the unit is level.
Fig. 30: Horizontal positioning
Connection of the medium piping
n The medium piping of the unit is designed
without any transition. The respective transition
(press fitting, soldering sleeve, etc.) can be
selected on an individual basis.
n For the purpose of servicing, connections must
be equipped with shut-of
f valves and the
medium flow rate adjusted using valves for
hydronic balancing.
n Additional automatic bleed valves are to be
provided in the supply and return flow at the
installation’s highest point.
n The medium piping may not exert any struc-
tural load on the unit.
n The line connections may not generate any
thermal or mechanical stresses on the unit. If
necessary cool the piping or support with the
second tool.
Necessary system components
Valve assembly (standard equipment)
With 2-conductor systems cold or warm medium is
fed through the register in the unit and then cold or
warm air is released. Regulation is realised by the
3-way valve assembly
. It comprises the electrically
actuated valve head and the valve body. If the
head is electrically activated, it actuates the body,
which routes the medium into the register. If the
temperature is reached, the head is switched off
and the medium is fed past the heat exchanger
through the bypass .
The bypass serves to ensure the minimum medium
flow rate for the chiller. In the case of units with 2-
way valve, no bypass is present. This version is
recommended with the use of a proportional pres-
sure-controlled circulation pump.
The time between being fully open and fully
closed can be approx. three minutes.
Valves for hydronic balancing
The calculated individual pressure losses in the
pipeline network layout for each individual unit are
adjusted to the entire system with hydronic bal-
ancing valves to be provided by the customer
. The
nominal flow rates for the medium adjust to the
values needed as a consequence of the pressure
loss.
REMKO WLT EC series
34
34

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw REMKO WLT-EC serie bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van REMKO WLT-EC serie in de taal/talen: Engels als bijlage per email.

De handleiding is 6,3 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van REMKO WLT-EC serie

REMKO WLT-EC serie Gebruiksaanwijzing - Nederlands - 60 pagina's

REMKO WLT-EC serie Gebruiksaanwijzing - Deutsch - 60 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info