587735
19
Verklein
Vergroot
Pagina terug
1/28
Pagina verder
19
G
A vacuum with a minimum of 0.05 mbar must be
created!
G
If the length of the connection line is longer than 5
m, refrigerant must be added to the system during
initial operation.
See the section Adding Refrigerant.
Winter Regulation
Mechanism
To ensure that the system functions properly, the pres-
sure and temperature of the refrigerant must be kept
within the operating ranges in the indoor unit and outdoor
part.
The integrated winter regulation mechanism makes it pos-
sible to keep operating ranges constant even when outside
temperatures go as low as –7 °C and to maintain the
cooling and heating operation.
The temperature sensor mounted on the output line of
the condenser records the condensation temperature of
the refrigerant in cooling mode.
18. Place the control line in the same line guideway.
19. Install the outdoor part with the wall or base console
onto stationary building parts approved for this pur-
pose.
Observe the installation instructions for the con-
soles.
20. Make sure that no structure-borne sound is trans-
mitted to building parts.
Structure-borne sound can be reduced through vi-
bration absorbers!
21. Remove the protective caps supplied and the screw
caps of the shut-off valves and use these for contin-
ued assembly.
22. Before you flare the refrigerant lines, ensure that
there is a swivel nut on the hose.
Only use the preinstalled swivel nuts.
23. Connect the refrigerant lines to the outdoor part as
already described.
Impermeability Test
Once all connections have been made, the manometer
station is connected to the corresponding valve connec-
tions as described below:
red = small valve = injection pressure.
blue = large valve = suction pressure.
After the connection has been made, an impermeability
test is conducted using dry nitrogen.
The connections that have been established are
sprayed with a leak locator spray to test for imperme-
ability. Tighten the bolts more firmly or, if necessary,
create a new flare.
After this test has been successfully conducted, any ex-
cess pressure is removed from the refrigerant lines and
a vacuum pump is put into operation to create a vac-
uum in the lines.
We recommend using a two-speed vacuum pump with
an absolute final partial pressure of at least 0.01 mbar
at a pump capacity of a minimum of 1.5 m3/h.
How long it takes to create the vacuum is based on the
hose line volume of the indoor unit and the length of the
refrigerant lines. However, this process takes a mini-
mum of 30 minutes.
Once foreign gases and moisture have been completely
removed from the system, the manometer station
valves are closed and the valves of the outdoor part are
opened as described in the section "Initial Operation".
The regulating mechanism controls the operating cur-
rent of the condenser fan by adjusting the current to the
required condensation temperature.
The winter regulation mechanism gradually adjusts the
condenser ventilator’s motor speed depending on the
operating pressure of the system and outside tempera-
ture.
For this reason, the rotating motion of the ventilator can
be completely discontinued in winter.
Temperature sensor
Winter regulation mechanism
19

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw REMKO RKS371H bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van REMKO RKS371H in de taal/talen: Engels als bijlage per email.

De handleiding is 1,6 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van REMKO RKS371H

REMKO RKS371H Gebruiksaanwijzing - Nederlands - 28 pagina's

REMKO RKS371H Gebruiksaanwijzing - Deutsch - 26 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info