726838
9
Verklein
Vergroot
Pagina terug
1/24
Pagina verder
9
Before the initial commissioning
1. Checked to ensure that
mechanical installation was
carried out correctly.
2. Proper connection
to the heating system provided
by the customer must
be checked.
3. Check whether hot surfaces are
protected against unintentional
contact.
4. Check whether the electrical
wiring of the units has been
established in accordance
with the valid guidelines and
standards and in accordance
with the accompanying circuit
diagrams.
5. The fan chamber and the intake
and exhaust areas must
be checked for foreign objects.
6. Check whether all blower
outlets are open.
7. Check that the fan moves easily.
8. Disconnect the power supply
to the switchgear (accessory)
and switch on the unit
with the control switch
on the switchgear.
Set the operating switch
for the relevant switchgear
to the “Off” or “0” position.
With longer breaks in operation:
Disconnect the electrical
connection at all poles
Shut off the heating medium
connection
If there is a danger of frost,
the complete system should
be emptied if the heating
medium (water) has not been
mixed with suitable anti-freeze
protection agent
Commissioning Shutdown
During initial commissioning
All regulating, control and safety
equipment must be checked
to ensure that it is functioning and
that the settings are correct during
initial commissioning.
1. The current consumption
of the fan must be measured.
The rated current may
not exceed the value
specified on the name plate
at the respective switching
speeds.
2. Check the fan's control/
regulation function.
3. Check the motor protection
function of the fan if installed
externally.
4. If installed, check that anti-
freeze protection device and
the room thermostats are
functioning.
5. Check the entire system for
tension-free installation and
potential vibrations.
6. Check the heating medium
supply lines for proper
connection and tightness.
CAUTION
Commissioning can only take
place once it has been assured
that the proper assembly
and electrical installation
correspond to the applicable
provisions of the EC Directives.
NOTE
Complete drainage of the heat
exchanger is only possible with
the aid of compressed air.
NOTE
After disconnecting
the switchgear from the power
supply, following a power supply
failure or a fault shut-down,
the control switch must always
be returned to the 0” position
before starting the unit again.
9

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw REMKO PWN HK serie bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van REMKO PWN HK serie in de taal/talen: Engels als bijlage per email.

De handleiding is 2,19 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van REMKO PWN HK serie

REMKO PWN HK serie Gebruiksaanwijzing - Nederlands - 24 pagina's

REMKO PWN HK serie Gebruiksaanwijzing - Deutsch - 24 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info