587557
7
Verklein
Vergroot
Pagina terug
1/16
Pagina verder
7
Infrared remote control
Inserting the batteries into the remote control
Prior to initial operation, the batteries supplied with the
unit (2 type AAA batteries) must be inserted into the re-
mote control.
1. Slide off the cover of the battery slot on the back of
the remote control.
10 Display "Fan speed"
The signal lights of the display indicate the set fan
speed.
Highest fan speed: "High" signal light
Medium fan speed: "Med" signal light
Lowest fan speed: "Low" signal light
11 Display "Operating mode"
The signal lights on the display indicate the set oper-
ating mode.
"Cool" signal light = Cooling
"Dehumidifier" signal light = Dehumidifying
"Fan" signal light = Ventilating
12 Display "Tank Full"
This light indicates that the floating switch of the in-
ternal tank has switched off unit operation. The inter-
nal tank does not become full during normal opera-
tion because the exhaust fan transports the accumu-
lated and evaporated condensation to the outside
via the exhaust hose.
Proceed as follows to resume unit operation after it
has automatically been switched off due to a mal-
function:
1. Switch the unit off by pressing the “On/Off” button
and unplug it from the power supply.
2. Place a suitable container under the condensa-
tion drain of the internal tank.
The condensation drain is located at the bottom
left at the back of the unit.
3. Pull the plug from the condensation drain and
collect the water that drains out.
4. Then replace the plug.
1,5 V
1,5 V
1,5 V
1,5 V
2. Place the batteries in the slot making sure that the
polarity is correct.
Use the labelling in the slot.
3. Close the battery slot again.
General information
The infrared remote control must be protected from
moisture.
When the unit is switched on, each change in the
settings is automatically transferred to the room air
conditioner. A beep indicates that the data has been
properly received.
The transmitter of the infrared remote control must
generally transfer changes to settings in the direc-
tion of the room air conditioner.
The infrared remote control’s range is approx. 5 m.
It is only possible for data to be properly transmitted
if there are no objects located between the transmit-
ter and the receiving unit such as doors, drapes,
blinds, etc.
Never use old and used batteries at the same time!
We recommend removing the batteries from the re-
mote control if the unit is taken out of operation for a
longer period of time.
*
Remove dead batteries immediately and replace
them with new batteries that meet quality stan-
dards because otherwise they may leak.
Remote control functions
All settings can also be made using an infrared remote
control. A description of the button functions can be
found in the “Control panel” section.
1 "On/Off” button
2 "Mode” button
3 "Fan Speed” button
4 "Timer” button
5 "Up/Down” buttons
1
ON/OFF Mode
Fan Speed Up
Timer Down
3
4
2
5
*
Keep in mind that if there is no plug or it is inserted
incorrectly, water may leak out after the unit has re-
sumed operation.
7

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw REMKO MKT260 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van REMKO MKT260 in de taal/talen: Engels als bijlage per email.

De handleiding is 1,15 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van REMKO MKT260

REMKO MKT260 Gebruiksaanwijzing - Nederlands - 16 pagina's

REMKO MKT260 Gebruiksaanwijzing - Deutsch - 16 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info