587981
21
Verklein
Vergroot
Pagina terug
1/60
Pagina verder
Mounting instructions for expert personnel
For the installation of the entire
system, the operating instruc-
tions of the indoor units and
the chiller and/or heating sys-
tem must be observed.
The indoor units and chiller
work independently. They do
not have to be interconnected.
Select an installation site that
guarantees free air inlet and
outlet. See the "Minimum
clearance" section.
Do not install the unit in the
direct vicinity of units with
intensive heat radiation.
Installation in the vicinity of
heat radiation reduces the unit
output.
Lift the unit only at the in-
tended points. Never load the
medium or refrigerant lines.
The medium connection lines,
valves, and connections must
be insulated in a vapour-
diffusion-tight manner. If
necessary, the condensate
line (only units with heat
pump function) must also be
insulated. In combined systems
with cooling and heating
modes, the requirements of
the current energy savings
ordinance (Energie-Einspar-
Verordnung (EnEV) in
Germany) must be observed.
Protect open lines against the
penetration of dirt. Never press
in the lines.
Avoid unnecessary bends.
Establish all electrical
connections according to the
locally valid regulations.
Always connect electrical
lines properly to the electrical
terminals.
Fires may otherwise result.
Observe the static and other
construction regulations and
conditions in regard to the
installation site.
When selecting the installation
site, pay attention to a possible
noise reflection of the units in
the environment and on the
mounting surface.
To prevent the transmission of
vibrations to the mounting sur-
face, the units must be mount-
ed on vibration-absorbent
materials or vibration-isolated
foundations.
Make sure the lines are also
vibration-isolated.
If special requirements are
placed on the noise emissions
of the installation site, locally
adapted sound insulation
measures must be taken.
In such cases, please contact
a corresponding specialist
consultant.
Important information
prior to installation
2 Vertical unit transport
Tension point
1 Upright unit transport
Transport
Bring the unit as close
as possible to the installation
site
while still in the original
packaging. In this way, you can
prevent
transport damage.
The units may be moved only
into their mounting position
(upright) using suitable means
of transport (Figure 1).
Secure against tipping!
The unit must be transported
in a vertical position to higher
installation sites (Figure 2).
Check the package contents
for completeness and check the
unit for visible transport dam-
age.
Report any damage immediate-
ly to your contracting partners
and the shipping company.
21
21

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw REMKO KWG500 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van REMKO KWG500 in de taal/talen: Engels als bijlage per email.

De handleiding is 7,1 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van REMKO KWG500

REMKO KWG500 Gebruiksaanwijzing - Deutsch - 60 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info