587906
30
Verklein
Vergroot
Pagina terug
1/44
Pagina verder
30
REMKO GPM
If the value is outside the specified
range, readjust with the CO2
regulating screw on the Venturi
tube.
- When the screw is tightened,
the gas flow rate decreases as
does the CO2 value.
- The CO2 value increases when
the screw is unscrewed.
Subsequently set the burner to
“minimum output” by pressing
and holding the rest button again
for 2 to 3 seconds.
Operation at “minimum output” is
indicated by the green LED rapidly
flashing twice.
Wait until the minimum output
at the burner has stabilised and
check that the CO2 value is equal
to or slightly below the CO2 value
at the maximum flow rate ( up to
-0.3%).
A deviating value can be corrected
with the offset screw.
To make changes to values,
remove the metal plug and turn
the regulating screw:
- the CO2 value decreases when
the screw is unscrewed,
- the CO2 value increases when
the screw is tightened.
After making any adjustments with
the offset regulating screw, the
CO2 value at maximum output
must be rechecked by carrying out
the above described steps.
After carrying out these steps,
set the burner to “normal” mode
by pressing and holding the reset
button again for 2 to 3 seconds.
This mode is indicated by the
green LED showing a steady light.
If the unit is not set to
“normal mode“, the control
board will automatically reset
the unit after 20 minutes.
NOTE
CO2 regulating
screw
Pressure measuring
connection gas
inlet
Offset regulation
Pressure measuring
connection gas
outlet
Calibrated
Venturi tube
If the unit is not used for a
prolonged period, the gas
valves must be closed and
the main switch of the unit
switched off.
ATTENTION
ATTENTION
The entrance of the Venturi
tube must under no
circumstances be covered by
the hands or other objects.
This can lead to flashback of
the premixing burner.
The unit performs a cooling
cycle in any event before the
fans are switched off.
NOTE
We reserve the right to make changes to dimensions and design in the interest of technological advances.
After carrying out all steps for
commissioning, the user must be
instructed in the operation of the
unit and its control.
If the unit is not set to “normal”
mode, the control board will
automatically reset the unit after
20 minutes.
This also occurs if the power
supply to the unit is disconnected
and then reconnected.
s
s
s
30

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw REMKO GPM 25 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van REMKO GPM 25 in de taal/talen: Engels als bijlage per email.

De handleiding is 4,39 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van REMKO GPM 25

REMKO GPM 25 Gebruiksaanwijzing - Nederlands - 44 pagina's

REMKO GPM 25 Gebruiksaanwijzing - Deutsch - 44 pagina's

REMKO GPM 25 Gebruiksaanwijzing - Français - 44 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info