587581
17
Verklein
Vergroot
Pagina terug
1/28
Pagina verder
Error indicated by flashing code
Display Cause Required action
88 flashes Power outage for 3 minutes Switch off and switch back on
E1 flashes Communication error display controller Contact specialist dealer
E2 flashes Circulation sensor on indoor unit faulty/tripped Contact specialist dealer
E3 flashes Frost protection sensor on indoor unit faulty/tripped Contact specialist dealer
E4 flashes Vaporiser fan motor speed too low/faulty Contact specialist dealer
E5 flashes No cooling/heating output after 30 minutes. Contact specialist dealer
E6 flashes Undervoltage protection has tripped Contact specialist dealer
E7 flashes Communication error
Reprogram (see chapter
“Programming when error E7 is indicated”)
Programming when error E7 is indicated
If error 07 "Communication error"
occurs, perform the following
programming procedure:
1. Prepare to reset the unit by
removing the batteries from the
remote control.
2. Press and hold / and put
the batteries back in the remote
control.
The display will show
"00 00 00"
3. If digit I is "0", proceed to
step "5".
4. If digit I is "1", press the
Programming E7
Digit I Digit II
Digit III Digit IV Digit V Digit VI
is displayed before continuing
with the programming
procedure!
10.
Point the transmitter on the IR
remote control at the receiver
on the indoor unit and press the
"ON/OFF" button until a beep
acknowledges that the signal
has been received. The first LED
on the right side flashes.
11.
After the acknowledgement
beep has sounded, remove
the batteries from the remote
control for approx. 1 minute.
Re-insert the batteries to
complete the programming
procedure. You can now select
the desired operating mode.
"MODE" button until digit I
changes to "0".
5. Program the 1st communication
code for digits I to VI by
pressing the following buttons
several times:
ATY 261: 04 54 05
ATY 351: 04 54 05
Verify that the correct code
is displayed before continuing
with the programming
procedure! 6. Press
the"MODE" button to save the
settings.
7. If the first digit is "1", proceed
to step "9".
8. If the first digit is "0", go back
to step "1." and repeat the
programming procedure.
9. Program the 2nd
communication code for digits I
to VI by pressing the following
buttons several times:
ATY 261: 1A 00 EA
ATY 351: 1A 00 Fb
Verify that the correct code
17
17

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw REMKO ATY351 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van REMKO ATY351 in de taal/talen: Engels als bijlage per email.

De handleiding is 1,65 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van REMKO ATY351

REMKO ATY351 Gebruiksaanwijzing - Nederlands - 28 pagina's

REMKO ATY351 Aanvulling / aanpassing - Deutsch - 1 pagina's

REMKO ATY351 Gebruiksaanwijzing - Deutsch - 28 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info