457183
11
Verklein
Vergroot
Pagina terug
1/27
Pagina verder
REL Acoustics ‘ST III’ User Manual
11
CONTROLS AND CONNECTIONS (Cont)
MODE SWITCH. Used to set phase* and to bypass crossover for Low Level input**.
Position 1 / Line: 0 degrees phase, crossover engaged low level input
Position 2 / LFE: 0 degrees phase, crossover bypassed for low level input
Position 3 / Line: 180 degrees phase, crossover engaged for low level input
Position 4 / LFE: 180 degrees phase, crossover bypassed for low level input
*Phase selection affects both Hi and Lo level inputs
**Crossover is always engaged for Hi level input regardless of mode switch
position.
LO LEVEL input volume control. Adjust for output level when using LO LEVEL phono
input
or balanced line level input XLR socket.
HI LEVEL input volume control. Adjust for output level when using HI INPUT Neutrik
socket or BAL HI INPUT Neutrik socket.
FINE ROLL OFF control. Fine adjustment of roll off point, used in conjunction with
Coarse Roll Off control (below). See chart on amplifier panel or in this manual, page 8,
for crossover frequencies determined by setting combinations of both controls.
COARSE ROLL OFF control. Coarse adjustment of roll off point, used in conjunction
with Fine Roll Off control (above). See chart on amplifier or in this manual, page 8, for
crossover frequencies determined by setting combinations of both controls.
0dB LO INPUT phono socket. Used to connect the Sub Bass System at low level to
the sub/LFE output of the amplifier/processor or left and right pre-amp outputs.
If Lo Level inputs are used to connect pre-amp right and left outputs then a 12dB
attenuator is available from REL to balance the two inputs.
Alternatively, a high quality Y-adaptor may be employed to connect at either input as
system gain characteristics demand.
+12dB LO INPUT phono socket . As 6 but a higher sensitivety. If LO LEVEL inputs
are used connected to pre-amp right and left outputs then a 12 dB attenuator is
available from REL to balance the two inputs.
Alternatively, a high quality Y-adaptor may be employed to connect at either input as
system gain characteristics demand.
BAL HI INPUT Neutrik Speakon socket. Used to connect the Sub Bass System at high
level to the speaker output of one channel of a differential output or bridged to mono
amplifier.
Note:- 230 volt models of Stentor III and Studio III have two BAL HI INPUTS.
UNBAL HI INPUT Neutrik Speakon socket. Used to connect the Sub Bass System at
high level to the main speaker output of amplifiers.
BAL LO INPUT XLR socket. Used to connect the Sub Bass System at low level to pre-
amplifier balanced line outputs. (Not on Strata III)
Note:- 230 volt models of Stentor III and Studio III have two balanced line inputs.
1
2
3
4
6
7
8
9
10
0
5
11

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw REL Acoustics ST III Range bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van REL Acoustics ST III Range in de taal/talen: Engels als bijlage per email.

De handleiding is 0,87 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info