698697
7
Verklein
Vergroot
Pagina terug
1/25
Pagina verder
12
EN
13
SPECIFICATIONS
A10S
Input sensitivity for 1W @8ohms -16,3 dBV
Input impedance 47kOhm
Voltage gain 38dB
Maximum input voltage 6V
Volume adjustment range 100dB
Balance adjustment range +/-6dB
Adjustment accuracy 0.1dB
Channel balance <0,05dB
Maximum voltage at speaker output 48V
Minimum speaker impedance 2.5 Ohm
Output power at 8 ohms 100W
Output power at 4 ohms 180W
Frequency response 1Hz-110kHz(-3dB)
Harmonic distortion <0.03%
Signal-to-noise ratio 75dB unweighted
Mains power connection 115V/230V switch
Power consumption in normal mode 15W
Power consumption at max volume 600W
Power consumption in standby mode <0,5W
Inputs 3 RCA
1 Line XLR
2 TosLink
1 SPDIF
1 USB
Speaker outputs 1 pair
Dimensions
Width including wooden sides 453 mm
Height including feet 130 mm
Depth with speaker terminals 345 mm
Weight 13.86Kg
INSTALLING
1. Select the correct voltage required on the back of the unit amplifier that matches the voltage coming
from the mains supply. Use the power cable supplied in the package to connect the equipment up to the
mains supply.
2. Check that the unit is switched off.
3. Connect up the auxiliary units that you want to use to the equipment‘s inputs. (RCA 1-3, TosLink, SPDIF,
USB) right channel = red / left channel = white or the symmetric analog XLR inputs can be used with
any compatible signal source.
(XLR pin assignments: Pin 1= ground; Pin 2 = plus / signal; Pin 3 = minus)
4. The screw terminals at the back are used for the speaker connections.
5. (See back of the equipment: right channel = 1 / left channel = 7). You must also ensure that the plus
and minus connections on the amplifier concur with the plus and minus connections on the speakers in
order to prevent polarity reversal.
6. Now switch your amplifier on.
Switch the mains switch (12) into the ON position on the back. The standby LED on the front will come
on.
7. Now press the multifunction knob (2) on the front or the button (2) on the remote control to start your
equipment.
Note:
As your A10S uses a special power-saving standby circuit, you can always switch on / off during normal
operation using the multifunction knob on the unit or the RC-3 remote control.
The RC-3 remote control makes it easier for you to change your settings.
Mute (button 2)
Balance setting (buttons 14 + 15)
Input settings for all jacks (button 3 + 4)
Example: Input settings
Select the signal source using buttons 11 (-) or 12 (+), then press button 22 (Prog.) and use the volume but-
tons (3 + 4) to set the desired input volume. To save, press button 22 (Prog.) again.
7

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Quadral AURUM A10S bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Quadral AURUM A10S in de taal/talen: Duits, Engels, Frans, Spaans als bijlage per email.

De handleiding is 1,21 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info