815520
1
Verklein
Vergroot
Pagina terug
1/28
Pagina verder
17094-803D 12/23
Owners Manual
Operation & Care
INSTALLER: Leave this manual with party responsible for use and operation.
OWNER: Retain this manual for future reference.
Contact your dealer with questions on installation, operation, or service.
R
EXPEDITION I WOOD INSERT
AUTOMATIC COMBUSTION
CONTROL (ACC)
MODEL NUMBER:
EXPEDITION-I
Installation and service of this appliance should be performed by
qualified personnel. Hearth & Home Technologies recommends
HHT Factory Trained or NFI certified professionals.
NOTE: To obtain a French translation of this manual,
please contact your dealer or visit www.quadrare.com
REMARQUE : Pour obtenir une traduction française de
ce manuel, s’il vous plaît contacter votre revendeur ou
visitez www.quadrare.com
• Donotstoreorusegasolineorotherammablevapors
and liquids in the vicinity of this or any other appliance.
• Donotoverre-Ifheaterorchimneyconnectorglows,
youareoverring.Overringwillvoidyourwarranty.
Comply with all minimum clearances to combustibles
asspecied.
Failuretocomplymaycausehousere.
If the information in these instructions
is not followed exactly, a re may result
causing property damage, personal injury,
or death.
WARNING
HOT SURFACES!
Glass and other surfaces are hot during
operation AND cool down.
WARNING
Hot glass and appliance will cause burns.
Do not touch glass until it is cooled
Use leather gloves when reloading fuel
NEVER allow children to touch glass
Keep children away
• CAREFULLY SUPERVISE children in same room
as appliance.
Alert children and adults to hazards of
high temperatures
High temperatures may ignite clothing or other
ammablematerials.
Keep clothing, furniture, draperies and other
ammablematerialsaway.
Fire Risk.
For use with solid wood fuel only.
Other fuels may over re and generate
poisonous gases (i.e. carbon monoxide).
WARNING
27094-803D 12/23
A. Sample of Serial Number / Safety Label
LOCATION:UNDERASHLIP,PULLOUTTOVIEW
NOTE: Clearances may only be reduced by means approved by the regulatory authority having
jurisdiction
and Welcome to the Quadra-Fire Family!
PREVENT HOUSE FIRES
Install and use only in accordance with manufacturer's installation, venting and operating
instructions.
CONTACT YOUR LOCAL BUILDING OR FIRE OFFICIALS ABOUT
RESTRICTIONS AND INSTALLATION INSPECTION IN YOUR AREA
Refer to manufacturer's instructions and local codes for precautions required for passing
chimney through a combustible wall or ceiling.
WARNING - For Mobile Homes: Do not
install in a sleeping room. An outside combustion air inlet must be provided and
unrestricted while unit is in use. The structural integrity of the mobile home floor, ceiling
and walls must be maintained. The insert must be properly grounded to the frame of the
mobile home. A complete relining of the chimney system with a 6 inch (152mm) diameter
listed stainless liner is required. Must be equipped with a spark arrestor cap. Outside Air
comes standard on the insert and must be installed before operating insert.
When used as a masonry insert stove, install only in a masonry fireplace built to national
and/or local codes. Do not remove brick or mortar to accommodate insert. Installation
requires a 5 foot minimum length of a starter pipe into existing chimney with airtight face
seal. A full reline with listed liner strongly reccomended.
Install only on a non-combustible hearth.
Approved for installation and use in factory built zero-clearance fireplaces conforming to
minimum fire chamber specifications. A complete relining of the chimney system with a 6
inch (152mm) diameter listed stainless liner is required.
In Canada a full length 6 inch (152mm) S635 flue liner is required as per ULC S628-93.
WARNING - Inspect and clean chimney frequently. Under certain conditions of use, creosote
buildup may occur rapidly.
Do not connect this unit to a chimney serving another appliance.
DANGER: Risk of electrical shock. Disconnect power supply before servicing. Route
power cord away from unit. Do not route cord under or in front of appliance. Electrical
Rating: 115 VAC 1.4 AMPS 60 Hz
Do not use grate or elevate fire. Build wood fire directly on hearth (firebrick).
Do not
overfire. If heater or chimney connector glows, you are overfiring.
Operate only with doors
closed. Open only to add fuel to the fire. Replace glass only with 5mm ceramic available
from your dealer.
DO NOT REMOVE THIS LABEL
HOT WHILE IN
OPERATION DO NOT
TOUCH, KEEP CHILDREN, CLOTHING AND FURNITURE
AWAY. CONTACT MAY CAUSE SKIN BURNS. SEE
NAMEPLATE AND INSTRUCTIONS.
CAUTION:
Factory-Built Floor
Protection under Hearth
Extension
Thermal & Ember Protection
Floor height 0 to 4.5 inches below
Insert Base: Materials with R value of
2.9 required.
Ember Protection Only
Greater than 4.5 inches below Insert
Base.
LISTED ROOM HEATER, SOLID FUEL TYPE
"For Use with Solid Wood Fuel Only."
Also for use in Mobile Home.
Made in U.S.A. of US and
imported parts.
7094-800A
U.S. ENVIRONMENTAL PROTECTION AGENCY
Certified to comply with 2020 crib wood particulate emission standards at 1.9 g/hr for single burn rate heaters.
This single burn rate wood heater is not approved for use with a flue damper.
This wood heater needs periodic inspection and repair for proper operation. Consult the owner’s manual for further
information. It is against federal regulations to operate this wood heater in a manner inconsistent with the operating
instructions in the owner’s manual.
Mfg by:
352 Mountain House Road
Halifax, PA 17032
www.quadrafire.com
R
Serial No. / N° de série
HF
BARCODE LABEL
EXPEDITION I
CONFORMS TO UL STD 1482 AND CERTIFIED TO ULC STD S628
21-670
21-661
Side Wall
FF
Fuel Door
Insert
BB
Fascia
or Trim
Maximum Mantel Depth - 12 inch (305mm)
Mantel
Hearth Extension
AA
C
C
D
D
E
E
Minimum Clearances To Combustible Material
Masonry, Heat Circulating & Factory-Built
Refer to Clearances on other label for Canada
A Sidewall to Center of Appliance 24.5 in.
B Mantel to Bottom of unit 44.75 in.
C Top Trim to Bottom of unit 42.5 in.
D Side Trim to Center of Appliance 23.75 in.
E Hearth Extension from Glass 16 in.
F H
earth Extenson from Fuel Loading Door
8 in.
USA ONLY
JAN FEB MAR APR MAY JUN JUL AUG SEP OCT NOV DEC
2022 2023 2024
SAMPLE
Test Lab &
Report Number
Mfg Date
Serial Number
Model Name
37094-803D 12/23
TABLE OF CONTENTS
Safety Alert Key:
DANGER!Indicatesahazardoussituationwhich,ifnotavoidedwill result in death or serious injury.
WARNING!Indicatesahazardoussituationwhich,ifnotavoidedcould result in death or serious injury.
CAUTION!Indicatesahazardoussituationwhich,ifnotavoided,could result in minor or moderate injury.
NOTICE:Indicatespracticeswhichmaycausedamagetotheapplianceortoproperty.
Quadra-FireisaregisteredtrademarkofHearth&HomeTechnologies.
A. Sample of Serial Number / Safety Label .................2
B.Warranty .........................................4
C.QuickStartGuide...................................6
1 Listing and Code Approvals
A.InsertSafetyCertication.............................7
B.InsertEmissionsCertication..........................7
C.BTU&E󰀩ciencySpecications........................7
D. Mobile Home Approved (USA only) .....................8
E.GlassSpecications.................................8
F. Sleeping Room .....................................8
G.California-Prop65..................................8
2 Operating Instructions
A.YourWoodAppliance ................................9
B. Fire Safety ........................................9
C.Overring ........................................9
D.Combustible/Non-combustibleMaterials ................10
E.SeasonedWood...................................10
F. Burning Process ...................................10
G. Automatic Combustion Control (ACC) ..................11
H.BurnRateandOperatingE󰀩ciency....................11
I.WoodFuel ........................................12
J. Building A Fire.....................................12
K. Blower Control Box with Snap Disc . . . . . . . . . . . . . . . . . . . .14
L.BlowerOperation ..................................14
M.Opacity(Smoke) ..................................14
N. Clear Space ......................................14
O.NegativePressure .................................15
P.FrequentlyAskedQuestions..........................15
3 Maintenance and Service
A.QuickReferenceMaintenanceGuide ..................16
B. Cleaningtheglass&Replacement ....................17
C. General Maintenance...............................17
D.CorrectBa󰀪e&BlanketPlacement....................19
4 Troubleshooting Guide .............................20
5 Reference Materials
A. Service and Maintenance Log . . . . . . . . . . . . . . . . . . . . . . . .21
B. Service Parts List ..................................23
= Contains updated information
47094-803D 12/23
Hearth & Home Technologies LLC
LIMITED LIFETIME WARRANTY
Hearth & Home Technologies LLC (“HHT”) extends the following warranty for HHT gas, wood, pellet and electric hearth appliances
(each a “Product” and collecvely, the “Product(s)”) and certain component parts set forth in the table below (“Component Part(s)”)
that are purchased from a HHT authorized dealer or distributor.
WARRANTY COVERAGE:
HHT warrants that the Products and their Component Parts will be free from defects in materials and workmanship for the applicable
period of Warranty coverage set forth in the table below (“Warranty Period”). If a Product or Component Parts are found to be
defecve in materials or workmanship during the applicable Warranty Period, HHT will, at its opon, repair the applicable Component
Part(s), replace the applicable Component Part(s), or refund the purchase price of the applicable Product(s). The maximum amount
recoverable under this Warranty is limited to the purchase price of the Product. This Warranty is transferable from the original purchaser
to subsequent owners, but the Warranty Period will not be extended in duraon or expanded in coverage for any such transfer. This
Warranty is subject to condions, exclusions, and limitaons as described below.
WARRANTY PERIOD:
Warranty coverage begins at the date of installaon. In the case of new home construcons, Warranty coverage begins on the date of
rst occupancy of the dwelling or six months aer the sale of the Product(s) by an independent, authorized HHT dealer or distributor,
whichever occurs earlier. However, the Warranty coverage shall commence no later than 24 months following the date of Product
shipment from HHT, regardless of the installaon or occupancy date.
The term “Lifeme” in the table below is dened as: 20 years from the beginning date of warranty coverage for gas appliances, 10 years
from the beginning date of warranty coverage for wood and pellet appliances, and 5 years from the beginning of warranty coverage
for standalone gas log sets. These me periods reect the minimum expected useful lives of the designated Component Parts under
normal operang condions.
Page 1 of 2
4021-645M 9/21
Component
Parts Labor Gas Pellet Wood Electric Venting Component Parts Covered by this Warranty
XAll parts except as covered by Warranty Conditions,
Warranty Exclusions, and Warranty Limitations listed
X X Igniters, Auger Motors, Electronic Components, and
Glass
X
Electrical components limited to modules, remotes/wall
switches, valves, pilots, blowers, junction boxes, wire
harnesses, transformers and lights (excluding light bulbs)
X X Molded Refractory Panels, Glass Liners
X
Burners and logs for standalone gas log sets
(Vented and Vent Free gas log sets not sold as
components of the fireplace or stove)
X
Vent Free Burners and Vent Free Log components of
HHT manufactured fireplaces or stoves
X X Castings, Medallions and Baffles
6 years 3 years XCatalysts
7 years 3 years X X Manifold tubes, HHT Chimney and Terminations
10 years 1 year X
Burners, logs and refractory components of HHT
manufactured fireplaces or stoves
Limited
Lifetime 3 years XXX Firebox and heat exchanger, FlexBurn® System
(engine, inner cover, access cover and fireback)
1 Year None XXXXX All purchased replacement parts
Warranty Period HHT Manufactured Appliances and Venting
All parts including handles, external enameled
components and other material except as covered by
Warranty Conditions, Warranty Exclusions, and
Warranty Limitations listed
2 years
X
1 Year X X X
2 Years
5 years 1 year
Firepots, burnpots, mechanical feeders/auger
assemblies
3 years X
5 years
B. Warranty
57094-803D 12/23
WARRANTY CONDITIONS:
Because HHT cannot control the quality of any Products sold by unauthorized sellers, this Warranty only covers Products that are
purchased through an HHT authorized dealer or distributor unless otherwise prohibited by law; a list of HHT authorized dealers
is available on the HHT branded websites.
This Warranty is only valid while the applicable Product remains at the site of original installaon.
This Warranty is only valid in the country in which the HHT authorized dealer or distributor that sold the applicable Product is
authorized to sell applicable Product.
Contact your installing distributor or dealer for Warranty service. If the installing dealer or distributor is unable to provide
necessary parts, contact the nearest HHT authorized dealer or supplier. Addional service fees may apply if you are seeking
Warranty service from a dealer other than the dealer from whom you originally purchased the applicable Product.
No HHT consumer should bear cost of warranty service or costs incurred while servicing warranty claims (i.e., travel, gas, or
mileage) when the service is performed within the terms of this Warranty. Check with your dealer or distributor in advance for
any costs to you when arranging a warranty call. Travel and shipping charges for parts are not covered by this Warranty.
WARRANTY EXCLUSIONS:
This Warranty does not cover the following:
Changes in surface nishes as a result of normal use. As a heang appliance, some changes in color of interior and exterior surface
nishes may occur. This is not a aw and is not covered under the Warranty.
Damage to printed, plated, or enameled surfaces caused by ngerprints, accidents, misuse, scratches, melted items or other
external sources and residues le on the plated surfaces from the use of abrasive cleaners or polishes.
Repair or replacement of parts that are subject to normal wear and tear during the Warranty Period are not covered. These parts
include: paint, wood and pellet gaskets, rebricks, grates, ame guides, baeries and the discoloraon of glass.
Minor expansion, contracon, or movement of certain parts causing noise. These condions are normal and complaints related to
this noise are not covered by this Warranty.
Damages resulng from: (1) failure to install, operate, or maintain the applicable Product in accordance with the installaon
instrucons, operang instrucons, and lisng agent idencaon label furnished with the applicable Product; (2) failure to
install the applicable Product in accordance with local building codes; (3) shipping or improper handling; (4) improper operaon,
abuse, misuse, connued operaon with damaged, corroded or failed components, accident, or improperly/incorrectly performed
repairs; (5) environmental condions, inadequate venlaon, negave pressure, or draing caused by ghtly sealed construcons,
insucient make-up air supply, or handling devices such as exhaust fans or forced air furnaces or other such causes; (6) use of fuels
other than those specied in the operaon instrucons; (7) installaon or use of components not supplied with the applicable
Product or any other components not expressly authorized and approved by HHT; (8) modicaon of the appliance not expressly
authorized and approved by HHT in wring; and/or (9) interrupons or uctuaons of electrical power supply to the applicable
Product.
Non-HHT venng components, hearth connecons or other accessories used in conjuncon with the applicable Product.
Any part of a pre-exisng replace system in which an insert or a decorave gas applicable Product is installed.
HHT’s obligaon under this Warranty does not extend to the Product’s capability to heat the desired space. Informaon is provided
to assist the consumer and the dealer in selecng the proper Product for the applicaon. Consideraon must be given to the
Product locaon and conguraon, environmental condions, insulaon and air ghtness of the structure.
This warranty is void if:
The applicable Product has been over-red, operated in atmospheres contaminated by chlorine, uorine, or other damaging
chemicals. Over-ring can be idened by, but not limited to, warped plates or tubes, deformaon/warping of interior cast iron
structure or components, rust colored cast iron, bubbling, cracking and discoloraon of steel or enamel nishes.
The applicable Product is subjected to prolonged periods of dampness or condensaon.
There is any damage to the applicable Product due to water or weather damage which is the result of, but not limited to, improper
chimney or venng installaon.
LIMITATIONS OF REMEDIES AND LIABILITY:
EXCEPT TO THE EXTENT PROVIDED BY LAW, HHT MAKES NO EXPRESS WARRANTIES OTHER THAN THE WARRANTY SPECIFIED
HEREIN. The owners exclusive remedy and HHT’s sole obligaon under this Warranty or in contract, tort or otherwise, shall be
limited to replacement of the Component Part(s), repair of the Component Part(s), or refund of the original purchase price of the
applicable Product(s), as specied above; provided, however, that (i) if HHT is unable to provide replacement of the Component
Part(s) and repair of the Component Part(s) is not commercially praccable or cannot be mely made, or (ii) the customer is
willing to accept a refund of the purchase price of the applicable Product(s), HHT may discharge all such obligaons by refunding
the purchase price of the applicable Product. In no event will HHT be liable for any incidental or consequenal damages caused
by defects in the applicable Product. Some States do not allow the exclusion or limitaon of incidental or consequenal damages,
so the above limitaon or exclusion may not apply to you. This Warranty gives you specic legal rights and you may also have
other rights which vary from State to State. THE DURATION OF ANY IMPLIED WARRANTY IS LIMITED TO DURATION OF THE
EXPRESSED WARRANTY SPECIFIED ABOVE FOR THE APPLICABLE PRODUCT. Some States do not allow limitaons on how long an
implied warranty lasts, so the above limitaon may not apply to you.
Page 2 of 2
4021-645M 9/21
67094-803D 12/23
C. Quick Start Guide
1 2 3
4 5
6 7
NOTE:Thesearegenericdrawingsandmaynotrepresentyourspecicmodel.
ITEMS NEEDED FOR FIRST FIRE: 10 Pieces of Newspaper, 10-20 Pieces of Dry
KindlingandFewPiecesofDrySplitWood.
The appliance is ready for
normal operation.
Warning! Risk of Fire.
Close and securely latch the door after
therehasstarted,andafterrefueling,
toprevent:
- Spillageofsmoke,ameandcarbon
monoxide
- Spillageofsparks,coals,andlogs
- Overring
DONOTleavetheapplianceunattended
with the door open.
Startingaremaynotrequireanopen
door for draft.
ACTIVATE
Start-Up Air Control
LOAD WOOD
ADD NEWSPAPER
ADD KINDLING
LIGHT THE PAPER
ADD MORE WOOD
77094-803D 12/23
Mode Number: EXPEDITION-I
Laboratory: PFSTECO
Report Number: 21-670
Type: Solid Fuel Type, Listed
Room Heater
Standard: UL1482,ULCS628and(UM)84-
HUD, Mobile Home Approved.
A. Insert Safety Certication
NOTE: This installation must conform with local codes.
Intheabsenceoflocalcodesyoumustcomplywiththe
UL1482, (UM) 84-HUD and NPFA211 in the U.S.A. and
the ULC S628-93 and CAN/CSA-B365 Installation
Codes in Canada. NOT APPROVED FOR MOBILE
HOME INSTALLATIONS IN CANADA!
C. BTU & E󰀩ciency Specications
EPA Certication #: 292-21
EPA Certied Emissions: 1.9 grams per hour
*LHV Tested E󰀩ciency: 70%
**HHV Tested E󰀩ciency: 65%
***EPA BTU Output: 23,800 to 27,400 / hr
****Peak BTU/Hour
Output: 37,400
Vent Size: 6 inches
Firebox Size: 1.45cubicfeet
Recommended Wood
Length: 18 inches
Fuel SeasonedCordWood
*WeightedaverageLHV(LowHeatingValue)e󰀩ciency
using Douglas Fir dimensional lumber and data collected
during EPA emission tests in accordance with the
requirementsofCSAB415.1.LHVassumesthemoisture
is already in a vapor state so there is no loss in energy
to vaporize.
**WeightedaverageHHV(HighHeatingValue)e󰀩ciency
using Douglas Fir dimensional lumber and data collected
during EPA emission tests in accordance with the
requirements of CSA B415.1. HHV includes the energy
required to vaporize the water in the fuel.
***ArangeofBTUoutputscalculatedusingHHVE󰀩ciency
and the burn rates from the EPA tests, using Douglas Fir
dimensional lumber.
**** A peak BTU out of the appliance calculated using
themaximumrsthourburnratefromtheHighEPATest
and BTU content of seasoned cordwood (8600) times
thee󰀩ciency.
This wood heater needs periodic inspection and repair for
properoperation.Itisagainstfederalregulationstooperate
this wood appliance in a manner inconsistent with operating
instructions in this manual.
Model Number: EXPEDITION-I
Laboratory: PFSTECO
Report Number: 21-661
Standard: ASTME2780-10
Can be found at:
www.quadrare.com/about-us/epa-certication
B. Insert Emissions Certication
1 1 Listing and Code Approvals
This EXPEDITION-IisCertiedtocomplywith
2020 crib wood particulate emission standards.
Approved for ZC reboxes.
87094-803D 12/23
D. Mobile Home Approved (USA only)
This appliance is approved for mobile home installations
when not installed in a sleeping room and when an
outside combustion air inlet is provided.
Thestructuralintegrityofthemobilehomeoor,ceiling,
and walls must be maintained.
This appliance must be properly grounded to the frame
of the mobile home with #8 copper ground wire, and
chimneymustbelistedtoUL103HToralistedUL-1777
fulllengthsixinch(152mm)diameterlinermustbeused.
Outside Air Kit, part OAK-ACC must be installed in a
mobile home installation.
E. Glass Specications
This appliance is equipped with 5mm ceramic glass.
Replaceglassonlywith5mmceramicglass.Pleasecontact
your dealer for replacement glass.
F. Sleeping Room
Whenanapplianceisinstalledinasleepingroomanoutside
airkitisrequiredanditisrecommendedthatasmokeand/
orCO alarm be installed inthebedroom.Thesizeofthe
roommustbeatleast50ft³per1,000Btu/hrstoveinput
G. California - Prop65
This product and the fuels used to operate this product (wood), and the
products of combustion of such fuels, can expose you to chemicals
including carbon black, which is known to the State of California to
cause cancer, and carbon monoxide, which is known to the State of
California to cause birth defects or other reproductive harm. For more
information go to: WWW.P65Warnings.ca.gov
WARNING
Improper installation, adjustment, alteration, service or
maintenance can cause injury or property damage.
Forassistanceoradditionalinformation,consultaqualied
installer, service agency or your dealer.
Hearth&HomeTechnologiesWILLNOTwarrantystoves
thatexhibitevidenceofover-ring.Evidenceofover-ring
includes,butisnotlimitedto:
Warpedairtube
Deterioratedrefractorybrickretainers
Deterioratedba󰀪eandotherinteriorcomponents
NOTE: Hearth & Home Technologies, manufacturer of
this appliance, reserves the right to alter its products, their
specicationsand/orpricewithoutnotice.
Installationanduseofanydamagedappliance.
Modicationoftheappliance.
InstallationotherthanasinstructedbyHearth&Home
Technologies.
Installation and/or use of any component part not
approvedbyHearth&HomeTechnologies.
Operating appliance without fully assembling
all components.
Operatingappliancewithoutlegsattached(ifsupplied
with unit).
DoNOTOverre-Ifapplianceorchimneyconnector
glows,youareoverring.
Anysuchactionthatmaycausearehazard.
Fire Risk.
Hearth & Home Technologies disclaims any
responsibility for, and the warranty will be
voidedby,thefollowingactions:
WARNING
97094-803D 12/23
Blower Controls
Surround:
Cast or Flat
Metal
Convection Fan
ACC Start-up Air
Control
Door Handle
Figure 9.1-GeneralOperatingParts
Ifyouexpectthatchildrenmaycomeintocontactwiththis
appliance, we recommend a barrier such as a decorative
screen. See your dealer for suggestions.
A. Your Wood Appliance
2 2 Operating Instructions
HOT SURFACES!
Glass and other surfaces are hot during
operation AND cool down.
WARNING
Hot glass will cause burns.
Do not touch glass until it is cooled
NEVER allow children to touch glass
Keep children away
CAREFULLYSUPERVISEchildreninsameroomas
appliance.
Alert children and adults to hazards of high
temperatures.
High temperatures may ignite clothing or other
ammablematerials.
Keep clothing, furniture, draperies and other
ammablematerialsaway.
Do not operate appliance before reading and
understanding operating instructions. Failure
to operate appliance according to operating
instructionscouldcausereorinjury.
WARNING
B. Fire Safety
To provide reasonable re safety, the following should be
givenseriousconsideration:
1. Installatleastonesmokedetectoroneachoorofyour
home to ensure your safety. They should be located away
from the heating appliance and close to the sleeping
areas. Follow the smoke detector manufacturer’s
placement and installation instructions, and be sure to
maintain regularly.
2. A conveniently located Class A re extinguisher to
contendwithsmallresresultingfromburningembers.
3. A CO detector should be installed in the room with
the appliance.
4. A practiced evacuation plan, consisting of at least two
escape routes.
5. Aplantodealwithachimneyreasfollows:
- Intheeventofachimneyre:
─ Evacuatethehouseimmediately
─ Notifyredepartment.
C. Over ring
Fire Risk. Do not over-re.
Over-ringmayignitecreosoteorwilldamage
the appliance and chimney.
WARNING
To prevent over-ring your appliance, DO NOT:
• Useammableliquids.
• Overloadwithwood.
Burn trash or large amounts of scrap lumber.
• Permittoomuchairtothere.
DO NOT OPERATE THE STOVE WITH THE LOAD
DOOR OPEN. OPERATION WITH THE LOAD DOOR
OPEN CAN CAUSE AN OVER-FIRING CONDITION TO
OCCUR. OVER-FIRING THE STOVE IS DANGEROUS
AND CAN RESULT IN PROPERTY DAMAGE, INJURY
OR LOSS OF LIFE.
CAUTION
10 7094-803D 12/23
D. Combustible/Non-combustible Materials
Combustible Material - Material made of or surfaced
withwood,compressedpaper,plantbers,plastics,or
any material capable of igniting and burning, whether
ame-proofedornot,plasteredornon-plastered.
Non-combustible Material - Material which will not
ignite and burn. Such materials are those consisting
entirelyofsteel,iron,brick,tile,slate,glassorplasters,
or any combination thereof.
Non-combustible Sealant Material - Sealants which
will not ignite and burn: Rutland, Inc. Fireplace Mortar
#63, Rutland 76R, Nuex 304, GE RTV106 or GE
RTB116 (or equivalent).
E. Seasoned Wood
Burn only dry seasoned wood. Store wood under cover,
outoftherainandsnow.Dryandwell-seasonedwoodwill
not only minimize the chance of creosote formation, but will
giveyouthemoste󰀩cientre.Evendrywoodcontainsat
least 15% moisture by weight, and should be burned hot
enoughtokeepthechimneyhotforaslongasittakesto
drythewoodout-aboutonehour.Itisawasteofenergyto
burnunseasonedwoodofanykind.
Deadwood lyingontheforestoorshouldbeconsidered
wet, and requires full seasoning time. Standing dead wood
can be considered to be about 2/3 seasoned. To tell if wood
isdryenoughtoburn,checktheendsofthelogs.Ifthere
arecracksradiatinginalldirectionsfromthecenter,itisdry.
Ifyourwoodsizzlesinthere,eventhoughthesurfaceis
dry, it may not be fully cured.
Hearth&HomeTechnologiesWILLNOTwarrantystoves
that exhibit evidence of over-ring. Evidence of over-
ringincludes,butisnotlimitedto:
• Warpedairtube
• Deterioratedrefractorybrickretainers
• Deterioratedba󰀪eandotherinteriorcomponents
1. Symptoms of Over-Firing
Symptoms of over-ring may include one or more of
thefollowing:
- Chimneyconnectororapplianceglowing.
- Roaring,rumblingnoises.
- Loudcrackingorbangingsounds.
- Metalwarping.
- Chimneyre.
2. What To Do if Your Appliance is Over-Firing
- Immediatelyclosethedoorandaircontrolstoreduce
airsupplytothere.
- Ifyoususpectachimneyre,calltheredepartment
and evacuate your house.
- Contactyourlocalchimneyprofessionalandhaveyour
appliance and vent pipe inspected for any damage.
- Do not use your appliance until the chimney
professional informs you it is safe to do so.
NOTICE: Improper operation can turn any wood
appliance into a smoldering environmental hazard.
Splitting wood before it is stored reduces drying time.
Woodshouldbestackedsothatbothends ofeachpiece
are exposed to air, since more drying occurs through the
cut ends than the sides. This is true even with wood that
has been split. Store wood under cover, such as in a shed,
or covered with a tarp, plastic, tar paper, sheets of scrap
plywood, etc., as uncovered wood can absorb water from
rain or snow, delaying the seasoning process.
F. Burning Process
Inrecentyearstherehasbeenanincreasingconcernabout
air quality. Much of the blame for poor air quality has been
placedontheburningofwoodforhomeheating.Inorder
toimprovethesituation,weatQuadra-Firehavedeveloped
cleaner-burning wood appliances that surpass the
requirements for emissions established by our governing
agencies. These wood appliances must be properly
operated in order to ensure that they perform the way they
are designed to perform.
1. Kindling or First Stage - Ithelpstoknowalittleabout
the actual process of burning in order to understand what
goesoninsideaappliance.Therststageofburningis
calledthekindlingstage.Inthisstage,thewoodisheated
to a temperature high enough to evaporate the moisture
which is present in all wood. The wood will reach the
boiling point of water (212°F) and will not get any hotter
until the water is evaporated. This process takes heat
from the coals and tends to cool the appliance.
Firerequiresthreethingstoburn-fuel,airandheat.So,
if heat is robbed from the appliance during the drying
stage, the new load of wood has reduced the chances
for a good clean burn. For this reason, it is always best to
burndry, seasonedrewood.Theheatgeneratedfrom
thereshouldbewarmingyourhomeandestablishing
the ue draft, not evaporating the moisture out of wet,
unseasoned wood, resulting in wasted heat.
2. Second Stage - The next stage of burning, the secondary
stage,istheperiodwhenthewoodgiveso󰀨ammable
gases which burn above the fuel with bright ames.
During this stage of burning it is very important that the
amesbemaintainedandnotallowedtogoout.Thiswill
ensurethecleanestpossiblere.
11 7094-803D 12/23
Figure 11.1
ACC Start-up Air
Control
To activate:
Push back until it stops and then pull forward until it stops
3. Final Stage - Thenalstageofburningisthecharcoal
stage. This occurs when the ammable gases have
been mostly burned and only charcoal remains. This is
a naturally clean portion of the burn. The coals burn with
hotblueames.
It is very important to reload your appliance while
enough lively hot coals remain in order to provide the
amountofheatneededtodryandrekindlethenextload
ofwood.ItisbesttoactivatetheACCbeforereloading
(Figure 11.1). This livens up the coal bed and reduces
excessiveemissions(opacity/smoke).Opendoorslowly
so that ash or smoke does not exit appliance through
opening.Youshouldalsobreakupanylargechunksand
distribute the coals so that the new wood is laid on hot
coals.
Air quality is important to all of us, and if we choose to use
wood to heat our homes we should do so responsibly.
To do this we need to learn to burn our appliances in
the cleanest way possible. Doing this will allow us to
continue using our wood appliances for many years to
come.
G. Automatic Combustion Control (ACC)
When using the Automatic Combustion Control (ACC)
system, you do not have to continually monitor the re.
OnceyousettheACCsystemitwillcontrolthereforyou.
Follow the instructions below to learn how to operate your
appliance with ease.
H. Burn Rate and Operating E󰀩ciency
For maximum operating e󰀩ciency
• Burndry,well-seasonedwood.
Follow these burn rate instructions below.
Burn Rate
1. Starting a Fire:
- Load appliance with wood and start re (reference
Quick Start Guide on page 6).
- ActivateACC.
2. Reloading:
- Addwoodasneeded.
- ActivateACC.
3. Adjusting the Burn Rate - This wood appliance is
designedtooptimizee󰀩ciencyatalltimes.Sincethere
are no user controls to adjust the burn rate, the easiest
method is to learn how many logs you need at a time for
theamountofheatdesired.Inadditiontotheamountof
woodandthesizeofthelogs,takethetimetoexperiment
with split and unsplit logs as split logs will burn faster
than unsplit logs.
NOTE:Ifusingtheblower,itshouldbeo󰀨fortherst30
minutes and then be operated in the desired setting at 30
minutes.
This wood appliance has a manufacturer-
set minimum low burn rate that must not be
altered.Itisagainstfederalregulationstoalter
this setting or otherwise operate this pellet
insert in a manner inconsistent with operating
instructions in this manual.
WARNING
12 7094-803D 12/23
I. Wood Fuel
Processed Solid Fuel Fire Logs
NOTpermittedforuseinthisappliance
Moisture
Hardwood vs Softwood
Your appliance performance depends on the quality of the
rewoodyouuse.
Seasoned wood contains about 8,000 BTUs per pound.
Hard woods are more dense than soft woods.
Hard woods contain 60% more BTUs than soft woods.
Hard woods require more time to season, burn slower
and are harder to ignite.
Soft woods require less time to dry, burn faster and are
easier to ignite.
• Starttherewithsoftwoodtobringtheapplianceupto
operating temperature and to establish draft.
Add hardwood for slow, even heat and longer burn time.
HARDWOODS SOFTWOODS
Alder Aspen
Apple Cedar
Birch Douglas Fir
Maple Pine
Oak Spruce
Poplar
NOTICE: Seasoning time may vary depending on
drying conditions.
The majority of the problems appliance owners experience
are caused by trying to burn wet, unseasoned wood.
• Wet, unseasoned wood requires energy to evaporate
the water instead of heating your home, and
Causes evaporating moisture which cools your chimney,
accelerating formation of creosote.
Seasoned Wood
Cut logs to size
• Splitto6inches(152mm)orlessindiameter
Air dry to a moisture content of not more than 20%
- Softwood-aboutninemonthstodry
- Hardwood-abouteighteenmonthstodry
Storing Wood
Stepstoensureproperlyseasonedwood:
• Stack wood to allow air to circulate freely around and
through woodpile.
• Elevate wood pile o󰀨 ground to allow air
circulation underneath.
Smaller pieces of wood dry faster. Any piece over 6 in.
(152mm)indiametershouldbesplit.
• Wood(wholeorsplit)shouldbe stacked so both ends
of each piece are exposed to air. More drying occurs
through the cut ends than the sides.
Store wood under cover to prevent water absorption
from rain or snow. Avoid covering the sides and
ends completely.
Fire Risk.
• DO NOT BURN GARBAGE OR
FLAMMABLE FLUIDS SUCH AS
GASOLINE,NAPHTHAORENGINEOIL.
• DoNOTburntreatedwoodorwoodwith
salt (driftwood).
WARNING
May generate carbon monoxide if burn material other
than wood.
May result in illness or possible death.
Fire Risk.
• DoNOTburnwetorgreenwood.
Store wood in dry location.
• Stack wood so both ends are exposed
to air.
Wet, unseasoned wood can cause
accumulation of creosote.
WARNING
Fire Risk
DoNOTstorewood:
• Infrontoftheappliance.
• In space required for loading or
ash removal.
WARNING
J. Building A Fire
Beforelightingyourrstreintheappliance:
NOTE: The special high temperature paint that your
appliance is nished with will cure as your appliance
heats. You will notice an odor and perhaps see some
vapor rise from the appliance surface; this is normal.
We recommend that you open a window until the odor
dissipates and paint is cured.
1. Conrmtheba󰀪eandceramicblanketarecorrectly
positioned.Theyshouldbetouchingbackofreboxand
securedintoBa󰀪eProtectionChannel(Figure 13.1
and Figure 13.2).
2. Remove all labels from glass.
13 7094-803D 12/23
There are many ways to build a re. The basic principle
is to light easily-ignitable tinder or paper, which ignites
the fast burning kindling, which in turn ignites the slow-
burningrewood.
Hereisonemethodthatworkswell:
1. Activate ACC.
2. Placeseveralwadsofcrushedpaperonthereboxoor.
Heatingtheuewithslightlycrumplednewspaperbefore
addingkindlingkeepssmoketoaminimum.
3. Laysmalldrysticksofkindlingontopofthepaper.
4. Makesurethatnomatchesorothercombustiblesarein
the immediate area of the appliance. Be sure the room is
ventilatedandtheueunobstructed.
5. Lightthepaperintheappliance.NEVERlightorrekindle
rewithkerosene,gasoline,orcharcoallighteruid;the
results can be fatal.
6. Once the kindling is burning quickly, add several full-
lengthlogs3to4inches(76-102mm)indiameter.Be
carefulnottosmotherthere.Stackthepiecesofwood
1/2 to 1 inch apart (13-25mm); near enough to keep
each other hot, but far enough away from each other to
allowairowbetweenthem.
7. Activate the timer system (ACC).
- This livens up the coal bed and reduces excessive
emissions(opacity/smoke).
- Opendoorslowlysothatashorsmokedoesnotexit
appliance through opening.
- Largelogsburnslowly,holdingarelonger.
- Smalllogsburnfastandhot,givingquickheat.
8. As long as there are hot coals, repeating steps 6 through
7willmaintainacontinuousre.
Fuelreloading:
1. This appliance has a large door with an exceptional
view of the re.
- Dooropens26inches(660mm)whichgoesbeyond
the standard size hearth pad covering the oor in
front of the appliance.
- Maywanttouseahearthruginfrontofthehearth
pad to protect the ooring from ash spillage and
continuous cleaning of carpet, etc.
2. Open door slowly so that ash or smoke does not exit
appliance through opening.
- Checktheleveloftheashbuild-up.Removeashifit
reachesthetopofthebrickcovers.Ashshouldnotbe
spillingoverthebrickcoversontotheashlip.
- Anyashorcoalsontheashlipcanbepressedinto
thedoorgasketandshortenthelifeofthegasket.
- Iftheashisleft to accumulate ontheashlipitcan
interfere with the door closing and/or falling out onto
the hearth pad or beyond.
Checktheashleveleachtimeyoureload.
Build re on brick rebox oor. Do NOT use grates,
andironsorothermethodstosupportfuel.Itwilladversely
a󰀨ectemissions.
Avoidbuildingtheretooclosetotheglass.
Baffle Board even with front
tube & resting on all tubes
Start-Up Air
Control
Figure 13.1
Tube Channels
Ceramic Blanket on Top
2 pc Baffle Board
Figure 13.2
WARNING
Fire Risk.
DoNOTstorewood:
Closer than required clearances to
combustibles to appliance
Within space required for loading or
ash removal.
DoNOToperateappliance:
Withappliancedooropen.
Withashremovalsystemdooropen.
WARNING
Fire Risk.
• DoNOTburnwetorgreenwood.
Store wood in dry location.
• Stack wood so both ends are exposed
to air.
Wet, unseasoned wood can cause accumulation of
creosote.
CAUTION
14 7094-803D 12/23
L. Blower Operation
1. Initial (cold) startup - PushtheStart-upAirControlback
until it stops. The blower tends to cool the appliance.
Leave the blower o󰀨 until the burn is well established,
i.e., 30 minutes.
K. Blower Control Box with Snap Disc
1. The blower will turn on/o󰀨 automatically when set to
AUTO(Figure 14.1).
2. WhensettoMANUAL,thefanwillturnon/o󰀨only.This
settingover-ridestheinternalsnapdisc.
3. Adjust the speed of the fan by turning the HIGH/LOW
knobtothedesiredsetting.
MANUAL: Overrides
the internal snap disc
AUTO: Fan will turn
ON/OFF automatically
and is controlled by the
internal snap disc
MANUAL: Overrides
the internal snap disc
AUTO: Fan will turn
ON/OFF automatically
and is controlled by the
internal snap disc
AUTO
MANUAL
Figure 14.1
NOTE: For maximum e󰀩ciency and lowest emissions,
when operating the blower in either the automatic or
manual setting for the blower o󰀨 until the burn is well
established, i.e., 30 minutes.
N. Clear Space
• DoNOTplacecombustibleobjectswithin4ft(1.2m)of
the front of appliance (Figure 14.2).
Mantel - Avoidplacingcandlesandotherheat-sensitive
objects on mantel or hearth. Heat may damage
these objects.
Figure 14.2
Maintain 4 ft (1.22m) clearance to
combustible in front of appliance
NOTICE:DoNOToperateacirculatingfanwithinclose
proximity, approximately 4 ft (1.2m), of appliance. Can
reverseairow,blowinghotairintoappliancecavity.Can
damage appliance blower due to overheating.
2. Theblowerisequippedwithvesettingswitch.Increase
blowerspeedbyturningthesettingknobclockwise.
M. Opacity (Smoke)
Opacity is the measure of how cleanly your appliance is
burning.Opacityismeasuredinpercent;100%opacity is
when an object is totally obscured by the smoke column
from a chimney, and 0% opacity means that no smoke
column can be seen. As you become familiar with your
appliance,youshould periodically check the opacity.This
willallowyoutoknowhowtoburnasnearlysmoke-freeas
possible (goal of 0% opacity).
When burning your rst re, you will experience
smoke and odor from the appliance resulting from the
curing of paint and burning o󰀨 of any oils remaining
from manufacturing.
Open windows during initial burn to dissipate smoke
and odors!
• Odorsmaybeirritatingtosensitiveindividuals.
• Smokedetectorsmayactivate.
CAUTION
Do NOT place combustible objects in front of the
appliance. High temperatures may ignite clothing,
furniture or draperies.
WARNING
15 7094-803D 12/23
Negative pressure results from the imbalance of air available
fortheappliancetooperateproperly.Itcanbestrongestin
lower levels of the house.
Causes include:
• Exhaustfans(kitchen,bath,etc.).
Range hoods.
Combustion air requirements for furnaces, water
appliances and other combustion appliances
Clothes dryers.
• Locationofreturn-airventstofurnaceorairconditioning.
• ImbalancesoftheHVACairhandlingsystem
• Upperlevelairleakssuchas:
- Recessedlighting
- Attichatch
- Ductleaks
P. Frequently Asked Questions
O. Negative Pressure
Table 15.1
ISSUES SOLUTIONS
Odorfromappliance Whenrstoperated,thisappliancemayreleaseanodorfortherstseveralhours.Thisiscaused
bythecuringofthepaintandtheburningo󰀨ofanyoilsremainingfrommanufacturing.
Metallic noise
Noise is caused by metal expanding and contracting as it heats up and cools down, similar to the
soundproducedbyafurnaceorheatingduct.Thisnoisedoesnota󰀨ecttheoperationorlongevity
of the appliance.
Whirringsound Iftheblowerhasbeeninstalled,theblowerproducesawhirringsoundwhichincreasesinvolume
as the speed is increased.
CONTACT YOUR DEALER for additional information regarding operation and troubleshooting.
Visit www.quadrare.com to nd a dealer.
Asphyxiation Risk.
Negative pressure can cause spillage
of combustion fumes, soot and
carbon monoxide.
Appliance needs to draft properly for safety.
WARNING
To minimize the e󰀨ects of negative air pressure:
• Installtheoutsideairkitwiththeintakefacingprevailing
winds during the heating season
Ensure adequate outdoor air for all combustion
appliances and exhaust equipment
Ensure furnace and air conditioning return vents are not
located in the immediate vicinity of the appliance
• Avoidinstallingtheappliancenear doors, walkways or
small isolated spaces
Recessed lighting should be a “sealed can” design
Attic hatches weather stripped or sealed
• Atticmountedductworkandairhandlerjointsandseams
taped or sealed
DoNOToperateacirculatingfanwithincloseproximity,
approximately4ft(1.2m),ofappliance:
Can reverse air ow, blowing hot air into
appliance cavity.
Can damage appliance blower due to overheating.
CAUTION
Fire Risk.
DO NOT BURN GARBAGE OR
FLAMMABLE FLUIDS SUCH AS
GASOLINE,NAPHTHAORENGINEOIL.
Do NOT burn treated wood or woodwith
salt (driftwood).
May generate carbon monoxide if burn material other
than wood.
May result in illness or possible death.
WARNING
Fire Risk.
Keep combustible materials, gasoline and
other ammable vapors and liquids clear
of appliance.
DoNOTstoreammablematerialsinthe
appliance’s vicinity.
DO NOT USE GASOLINE, LANTERN FUEL,
KEROSENE, CHARCOAL LIGHTER FLUID OR
SIMILARLIQUIDSTOSTARTOR“FRESHENUP”
AFIREINTHISAPPLIANCE.
Keep all such liquids well away from the appliance
while it is in use.
Combustible materials may ignite.
WARNING
16 7094-803D 12/23
A. Quick Reference Maintenance Guide
Whenproperlymaintained,yourappliancewillgiveyoumany
yearsoftrouble-freeservice.Contactyourdealertoanswer
questions regarding proper operation, troubleshooting
and service for your appliance. Visit www.quadrare.com/
owner-resources to view basic troubleshooting, FAQs, use
&carevideos.
FREQUENCY TASK
Ba󰀪e&Blanket
MONTHLY
or after every
one (1) cord of
wood
Ba󰀪eandblanketplacementiscriticaltoheatoutput,e󰀩ciencyand
overalllifeoftheappliance.Makesuretheba󰀪eispushedallofthe
waytothebackofthereboxandtheblanketislayingat.Inspect
ba󰀪eforcracks.
Ceramic Blanket
Back of Firebox
Baffle Board
Baffle Retainer
Bracket
Blower
YEARLY or after
every four (4)
cords of wood
Vacuum the blower impellers.
Chimney System
EVERYTWO
MONTHS
or after every
four (4) cords of
wood
The chimney and chimney cap must be inspected for soot and
creosote every two months during the burn season or more frequency
ifchimneyexceedsorisunder14-16ft(4.3m-4.8m)measuredfrom
bottom of appliance.
Thiswillpreventpipeblockage,poordraft,andchimneyres.
Alwaysburndrywoodtohelppreventcapblockageandcreosote
build-up.
Firebrick&AshRemoval
WEEKLY
orafterevery25
loads of wood
Ashesmustbecoolbeforeyoucandisposeoftheashesinanon-
combustible container.
Firebrickisdesignedtoprotectyourrebox.Afterashesareremoved,
inspecttherebrickandreplacerebricksthatarecrumbling,cracked
orbroken.
Door&GlassAssemblies
WEEKLY
orafterevery25
loads of wood
Keepdoorandglassgasketingoodshapetomaintaingoodburn.
Totest: place a dollar bill between the appliance and door and then
shutthedoor.Ifyoucanpullthedollarout,removeonewasherfrom
doorhandlebehindlatchcamandtryagain.Ifyoucanstillpullitout,
replacethedoorgasket.
Checktheglassframeforloosescrewstopreventairleakage.
Checkglassforcracks.
Door Handles
WEEKLY
orafterevery25
loads of wood
Checkthedoorlatchforproperadjustment.Thisisveryimportant
especially after the door rope has formed to the appliance face.
Checkdoorhandleforsmoothcamoperation.
These are generic drawings and may not represent your model.
Table 16.1
3 3 Maintenance and Service
Allow the appliance to completely cool down before
performinganycleaningormaintenance.Starttherst
inspectionaftertherst2monthsofuse,orifperformance
changes, and adjust your schedule accordingly.
Maintenance is required for safe operation and must be
performed to maintain your warranty.
CAUTION
17 7094-803D 12/23
B. Cleaning the Glass & Replacement
Mostofthecarbondepositsontheglasswillburno󰀨during
hotres.
However, the ash residue that accumulates on the glass
surface should be removed regularly to prevent etching. To
cleantheglass,followthisprocedure:
Be sure the glass is completely cool.
Clean the glass with water or a cleaner made especially for
this purpose. Do not use abrasive cleaners. Use cleaning
agentssparinglyandbesuretokeepthemo󰀨theouter
surfaces of the stove.
Rinse the glass thoroughly.
Dry the glass completely.
Replace Broken Glass Immediately
Do not operate your stove if the glass in the doors is damaged.
Ifyouneedtoreplacetheglass,useonlythehightemperature
5mmceramicglasssuppliedbyQuadra-Fire.Donotuse
substitutes.
Service Part: SRV7094-054
1. Ensurethatthereisoutandtheapplianceiscooltothe
touch.
2. Protect a table or counter top with padding or towels.
Protect your hands and wear gloves to prevent injury.
3. Removethedoorwiththebrokenglassbyliftingthedoor
upando󰀨ofthehinges.
4. Laydoorfacedownonatableorcountermakingsure
thehandlehangsovertheedgesothedoorlaysat,on
a soft surface.
5. Removethescrewsfromeachglassretainerandremove
the glass. (If screws are di󰀩cult to remove, soak with
penetratingoilrst).
6. Center the glass with edges evenly overlapping the
opening in the door, (i.e. same space top and bottom,
left and right sides).
7. Replace the glass retainers. Be careful not to cross
thread the screws.
8. Tighten each retainer just a few turns until each is
secured. Check again for centering of glass in door
frame. Continue to tighten each retainer alternately, a
few turns at a time, until the glass is secure.
NOTE: DO NOT OVER TIGHTEN RETAINERS - can
causeglasstobreak.
9. Replace the door on the appliance.
Quadra-Fire appliances are equipped with ceramic super
heat-resistant glass, which can only be broken by impact
or misuse.
Injury Risk.
• Useonlyglassspeciedinmanual.
• DONOTREPLACEwithanyothermaterial.
WARNING
Handle glass assembly with care.
When cleaning glass:
Glass
Assembly
CAUTION
• Avoidstriking,scratchingorslammingglass.
• DoNOTcleanglasswhenhot.
• DoNOTuseabrasivecleaners.
• Useahardwaterdepositglasscleaneronwhitelm.
Use commercial oven cleaner on heavier deposits.
Remove all residue of oven cleaner or will permanently
stainglassonnextring.
Refer to maintenance instructions.
C. General Maintenance
1. Creosote (Chimney) Cleaning
• Frequency: Every 2 months during heating season
or as recommended by a certied chimney sweep;
morefrequentlyifchimneyexceedsorisunder14-16
ft. (measured from bottom of appliance)
• By:CertiedChimneySweep
Removeallashfromthereboxandextinguishallhotembers
before disposal. Allow the appliance to cool completely.
Disconnectuepipeorremoveba󰀪eandceramicblanket
fromappliancebeforecleaningchimney.Otherwiseresidue
canpileupontopoftheba󰀪eandceramicblanketandthe
appliancewillnotworkproperly.(SeeBa󰀪e Board on page
19). Close the door tightly. The creosote or soot should be
removedwithabrushspecicallydesignedforthetypeof
chimneyinuse.Cleanoutfallenashesfromtherebox.
It is also recommended that before each heating season
the entire system be professionally inspected, cleaned and
repaired, if necessary.
Inspection - Inspectthesystemattheapplianceconnection
and at the chimney top. Cooler surfaces tend to build
creosote deposits quicker, so it is important to check the
chimney from the top as well as from the bottom.
Formation and Need For Removal - Whenwoodisburned
slowly, it produces tar and other organic vapors which
combine with expelled moisture to form creosote.
The creosote vapors condense in the relatively cool
chimneyue of a newly-started or aslow-burningre.As
a result, creosote residue accumulates on the ue lining.
When ignited, this creosote creates an extremely hot re
which may damage the chimney or even destroy the house.
The chimney connector and chimney should be inspected
once every 2 months during the heating season to determine
if a creosote or soot buildup has occurred. If creosote or
soot has accumulated, it should be removed to reduce the
riskofachimneyre.
18 7094-803D 12/23
2. Disposal of Ashes
• Frequency:
Whenashiswithin1-3/4in.(44mm)of
reboxlip
• By: Homeowner
3. Appliance Inspection
• Frequency: Every 2 months at the same time the
chimney and chimney connector are inspected.
• By: Homeowner
Check for:
• Cracksinglass
• Doorhandle-smoothcamoperation
• Ba󰀪eandceramicblanketcorrectplacement
• Ba󰀪eforwarp-age
• Firebrickforcracks,brokenorcrumbly
• Doorgasket(Dollarbilltest):Placeadollarbillbetween
thestoveandthedoorandthenshutthedoor.Ifyoucan
pullthedollarbillout,replacethedoorgasket.
Glass frame for loose screws
4. Glass Cleaning
• Frequency: As desired
• By: Homeowner
Ashes should be placed in a metal container with a tight
ttinglid.Theclosedcontainerofashesshouldbeplaced
on a non-combustible oor or on the ground, well away
fromallcombustiblematerials,pendingnaldisposal.Ifthe
ashes are disposed of by burial in soil or otherwise locally
dispersed, they should be retained in the closed container
until all cinders have thoroughly cooled.
Fire Risk.
Prevent creosote buildup.
• Inspect chimney connector and
chimney once every two months during
heating season.
• Remove creosote to reduce risk of
chimneyre.
• IgnitedcreosoteisextremelyHOT.
WARNING
Fire Risk.
Ashes could contain hot embers.
WARNING
Fire Risk. Disposal of Ashes
Ashes should be placed in metal container
withtightttinglid.
Do not place metal container on
combustible surface.
WARNING
Ashes should be retained in closed container until all
cinders have thoroughly cooled.
Fire Risk.
• Do not use chimney cleaners or ame
colorants in your appliance. Will corrode
chimney pipe.
WARNING
Clean glass with a non-abrasive glass cleaner. Abrasive
cleaners may scratch and cause glass to crack. If the
deposits on the glass are not very heavy, normal glass
cleanersworkwell.Heavierdepositsmayberemovedby
using a damp cloth dipped in wood ashes or by using a
commercially available oven cleaner.
After using an oven cleaner, it is advisable to remove any
residue with a glass cleaner or soap and water. Oven
cleanerleftonduringthenextringcanpermanentlystain
theglassanddamagethenishonmetalsurfaces.
A portion of the combustion air entering the rebox is
deected down over the inside of the door glass. This
air ow “washes” the glass, helping to keep smoke from
adhering to its surface.
5. Cleaning Plated Surfaces
• Frequency: Prior to first burn and then as desired
• By: Homeowner
Handle glass assembly with care. Glass is breakable.
Avoidstriking,scratchingorslammingglass
Avoid abrasive cleaners
Do not clean glass while it is hot
CAUTION
Do not use polishes with abrasives. It will scratch
plated surfaces.
CAUTION
19 7094-803D 12/23
Clean all the ngerprints and oils from plated surfaces
BEFORE ringtheapplianceforthersttime.Ifnotcleaned
properly before lighting your rst re, the oils can cause
permanentmarkingsontheplating.
Afterthe plating is cured, theoilswillnot a󰀨ect the nish
andlittlemaintenanceisrequired.Wipecleanasneeded.
6. Inspect Firebrick
• Frequency: After each ash removal
• By: Homeowner
Replacetherebrickiftheybecomecrumblyand/orifthere
isa1/4inch(6.35mm)gapbetweenthebricks.
The rebox is lined with rebrick, which has exceptional
insulatingproperties.Donotuseagrate;simplybuildareon
thereboxoor.Donotoperateappliancewithoutrebrick.
1. After the coals have completely cooled, remove all old
brickandashfromunitandvacuumrebox.
2. Remove new brick set from box and lay out to the
diagram shown in the instructions that come with the
bricksetorrefertothediagramontheservicepartslist
at the end of this manual.
3. Laybottombricksinunit.
4. Installrearbricksonthetopofthebottombricks.Slide
topofbricksundercliponbackofreboxwallandpush
bottomofbricksback.
5. Installsidebricks.Slidetopofbrickunderclipsonside
ofreboxandpushthebottomofthebrickuntilitisush
with the side of the unit.
D. Correct Ba󰀪e & Blanket Placement
NOTE: These are generic drawings and may not
representyourspecicmodel.
NOTE: A missing, damaged or improperly positioned
ba󰀪e is dangerous and may cause damage and poor
e󰀩ciency.Itwillalsovoidyourwarranty.
WARNING
Fire Risk.
Firebox damage due to improper ba󰀪e
placementisnotcoveredbywarranty.Operate
thewood burningappliancewith theba󰀪ein
the correct position only.
Notdoingsocouldresultin:
Reducede󰀩ciency
Overheatingthechimney
Overheatingtherearoftherebox
Poor performance
Ensure correct ba󰀪e placement and replace ba󰀪e
components if damaged or missing.
The ba󰀪e boards are FRAGILE. Use extreme caution
whenloadingrewoodtoprevent:
Cracking,breakingordamagingtheba󰀪eboards
DONOToperatetheappliancewithoutba󰀪eboards
CAUTION
Ceramic Blanket
Back of Firebox
Baffle Board
Baffle Retainer
Bracket
CORRECT POSITION
Figure 19.1-CorrectBa󰀪eandBlanketPositions
CeramicBlanket andBa󰀪eBoardMUSTbeincontact
withthebackofthereboxandevenwitheachotherin
the front.
INCORRECT POSITIONS
CeramicBlanketandBa󰀪eBoardareNOTincontactwiththe
backoftherebox.
CeramicBlanketisNOTincontactwiththebackoftherebox
andNOTevenwiththeBa󰀪eBoardinthefront.
Figure 19.2-IncorrectBa󰀪eandBlanketPositions
CeramicBlanketisbunchedupatthebackofthereboxand
NOTevenwiththeBa󰀪eBoardinthefront.
Ceramic Blanket
Back of
Firebox
Baffle Board
20 7094-803D 12/23
Withproperinstallation,operation,andmaintenanceyourwoodappliancewillprovideyearsoftrouble-freeservice.Ifyoudo
experienceaproblem,thistroubleshootingguidewillassistyouoraqualiedservicepersoninthediagnosisofaproblem
andthecorrectiveactiontobetaken.
Table 20.1
Start Fire Problems Possible Cause Solution
Cannotgetrestarted
Excessivesmokeorspillage
Burns too slowly
Not enough heat output
Notenoughkindling/paperorno
kindling/paper
Usedrykindling,morepaper.Arrangekindling&
wood for air movement.
Notenoughairforretoignite
Checkforrestrictedterminationcap
Checkforblockageofoutsideairkit;ifinstalled.
Checkforueblockage.
Pre-warmuebeforestartingre(refertoBuilding
a Fire on page 12).
Checkforadequateventheight(refertoChimney
Height / Rise and Run on page 14 in the
Installationmanual).
Openwindowbelowtheappliancetowards
the wind.
Woodconditionistoowet,toolarge Use dry, seasoned wood (refer to Seasoned
Wood on page 10).
Bed of coals not established before
adding wood
Startwithpaper&kindlingtoestablishbedofcoals
(refer to Building a Fire on page 12).
Flueblockagesuchasbirds’nestsor
leaves in termination cap
Have chimney inspected for creosote and cleaned
byacertiedchimneysweep.
Down draft or negative pressure
Competition with exhaust devices
Donotuseexhaustfansduringstart-up(referto
Negative Pressure on page 15).
Openwindowbelowtheappliancetowards
the wind.
Fire burns too fast
Extremely dry or soft wood
Mix in hardwood.
Mixinlessseasonedwoodafterreisestablished
(refer to Wood Fuel on page 12).
Overdrafting
Checkforcorrectventheight;toomuchvertical
height creates over drafting.
Checklocationofventtermination(referto
Chimney Termination Requirement on page 13
in the Installationmanual).
4 4 Troubleshooting Guide
21 7094-803D 12/23
A. Service and Maintenance Log
Date of Service Performed By Description of Service
5 5 Reference Materials
22 7094-803D 12/23
Date of Service Performed By Description of Service
23 7094-803D 12/23
B. Service Parts List
Service Parts
REXPEDITION-I
Beginning Manufacturing Date: May 2022
Ending Manufacturing Date: Active
Cast Iron Wood Insert
Part number list on following page.
12/23
8
7
6
10
9
12
13
14
15
18 19
20
21
1
2
3
4
5
21
11
17
16
24 7094-803D 12/23
Service Parts
REXPEDITION-I
Beginning Manufacturing Date: May 2022
Ending Manufacturing Date: Active
IMPORTANT: THIS IS DATED INFORMATION. Parts must be ordered from a dealer or distributor. Hearth and
Home Technologies does not sell directly to consumers. Provide model number and serial number when
requesting service parts from your dealer or distributor. Stocked at
Depot
ITEM DESCRIPTION COMMENTS PART NUMBER
1 Convection Back SRV7094-161
Hurricane Screw Pkg of 40 SRV2005-861/40 Y
Screw, Hwh Ms 1/4-20 X 3/4 Ns Pkg of 25 220-0080/25 Y
2Flue Attach Ring SRV7095-203
Bolt 5/16 X 18 X 1 7000-571 Y
Nut, 5/16-18 Pkg of 10 A-3483-1/10 Y
3 Gasket, Flue Collar SRV7044-194
4Chimney Ring Attach SRV7044-181
5Flue Ba󰀪e Plate SRV7094-185
6 Rear Brick Retainer SRV7094-127
Screw, Hwh Ms 1/4-20 X 3/4 Ns Pkg of 25 220-0080/25 Y
7 Ceramic Fiber Blanket SRV7094-118 Y
8Ba󰀪e Board Pkg of 2 SRV7094-117 Y
9Secondary Tubes Pkg of 3 SRV7094-121
Screw, Hwh Ms 1/4-20 X 3/4 Ns Pkg of 25 220-0080/25 Y
Nut, Flange 1/4-20 Pkg of 24 226-0130/24 Y
10 Ba󰀪e Protection Channel SRV7094-119 Y
11 Brick Assembly SRV7094-022 Y
11.1 Brick, Uncut (9” X 4.5” X 1.25”) Qty 8 req 832-0550 Y
11.2 Brick, 7” X 4.5” X 1.25” Qty 5 req SRV7128-011
11.3 Brick, 9” X 2” X 1.25” Qty 1 req SRV7128-018
Brick, Uncut (9” X 4.5” X 1.25”) Pkg of 6 832-3040
Additional service part numbers appear on following page.
#11 Brick Assembly
#10 Ba󰀪e Protection Channel
Fiber baffle
Ceramic blanket
Side view
Baffle protection channel
sits in between front tube
and fiber baffle
This tab sits behind the front tube
Front, looking into unit
11.1
11.2
11.3
11.1
11.1
11.1
11.1
11.1
11.1
11.1
11.2 11.2 11.2
11.2
25 7094-803D 12/23
Service Parts
REXPEDITION-I
Beginning Manufacturing Date: May 2022
Ending Manufacturing Date: Active
IMPORTANT: THIS IS DATED INFORMATION. Parts must be ordered from a dealer or
distributor. Hearth and Home Technologies does not sell directly to consumers. Provide
model number and serial number when requesting service parts from your dealer or distributor.
Stocked
at Depot
ITEM DESCRIPTION COMMENTS PART NUMBER
12 Door Assembly SRV7094-053
12.1 Door SRV7094-205
12.2 Glass Assembly SRV7094-054
12.3 Glass Retainers Pgk of 4 SRV7094-174
Screw, Pan Head Phillips, 10-24 x 3/8 Pkg of 10 1200983-10 Y
12.4 Door Gasket 10 Feet 1-00-1203668 Y
13 Door Handle Assembly SRV7063-014 Y
13.1 Fiber Handle SRV7060-212 Y
13.2 Door Handle SRV7063-137
13.3 Key, cam Latch SRV430-1151
13.4 Washer, Sae 3/8 ( 3 ea) Pkg of 3 832-0990 Y
13.5 Cam Latch SRV430-1141
13.6 Nut, Side Lock Jam Pkg of 24 226-0100/24 Y
Hinge Pins Pkg of 2 844-3290
14 Front SRV7094-201
Wire Jacket Rope, 1/2 7000-811/10
15 Fascia Assembly SRV7094-057
15.1 Front Trim, Upper (w/Screen) SRV7094-209
Screw, Pan Head phillips 10-24 x 3/8 Pkg of 10 1200983-10 Y
15.2 Front Trim, Lower (w/Screen) SRV7094-211
Screw, Pan Head phillips 10-24 x 3/8 Pkg of 10 1200983-10 Y
15.3 Fascia Weldment SRV7095-061
Additional service part numbers appear on following page.
#12 Door Assembly #13 Door Handle Assembly
#15 Fascia Assembly
12.4
13
12.2
12.3
12.1
13.1
13.6
13.3
13.4
13.5
13.2
15.2
15.1
15.3
26 7094-803D 12/23
Service Parts
REXPEDITION-I
Beginning Manufacturing Date: May 2022
Ending Manufacturing Date: Active
IMPORTANT: THIS IS DATED INFORMATION. Parts must be ordered from a dealer or
distributor. Hearth and Home Technologies does not sell directly to consumers. Provide
model number and serial number when requesting service parts from your dealer or distributor.
Stocked
at Depot
ITEM DESCRIPTION COMMENTS PART NUMBER
16 Control Panel Assembly SRV7095-026
16.1 Speed Control SRV7000-888 Y
16.2 Knob, Speed Control SRV7000-930 Y
16.3 Rocker Switch (Round) SRV7000-940 Y
17.1 Snap Disc Box Assembly SRV7094-068 Y
17.2 Snap Disc SRV230-0470 Y
17.3 Power Cord 96 inches 3-20-51578 Y
17.4 Wire Harness SRV7000-891 Y
17.5 Blower Replacement SRV7000-868 Y
17.6 Blower Housing SRV7094-032
18 Timer Control Assembly SRV7094-025 Y
Knob Pkg of 2 32284/2 Y
Screw, Pan Head phillips 8-32 x 3/8 Pkg of 40 225-0500/40 Y
Timer (Only) Replacement Assembly SRV480-1940 Y
19 OA Cover SRV7094-234 Y
20 Secondary Box/Covers Includes left & right SRV7094-125
Screw, Machine Screw 1/4-20 x 3/4 Ns Pkg of 25 220-0080/25 Y
Hurricane Screw Pkg of 40 SRV2005-861/40 Y
Additional service part numbers appear on following page.
#16 Control Panel Assembly
#17 Blower Assembly
17.1
17.2
17.3 17.4 17.5
17.6
16.2
16.1
16.3
27 7094-803D 12/23
Service Parts
REXPEDITION-I
Beginning Manufacturing Date: May 2022
Ending Manufacturing Date: Active
IMPORTANT: THIS IS DATED INFORMATION. Parts must be ordered from a dealer or
distributor. Hearth and Home Technologies does not sell directly to consumers. Provide
model number and serial number when requesting service parts from your dealer or distributor.
Stocked
at Depot
ITEM DESCRIPTION COMMENTS PART NUMBER
21 Combustion Cover Includes left & right SRV7094-134
Hurricane Screw Pkg of 40 SRV2005-861/40 Y
Component Pack SRV7094-062
Surround 43 x 31 SP1-4331
Surround Trim Assembly 43 x 31 TRIMKIT-4331-NL
Surround 38 x 28 SP1-3828
Surround Trim Assembly 38 x 28 TRIMKIT-3828-NL
Surround Cast Trim 43 x 31 CT1-4331
Custom Surround CUST-SP1-SPL
22 Trim Cast, Full Set 811-0930
22.1 Footer, Left 414-7090MBK
22.2 Trim Leg, Left 414-7120MBK
22.3 Header 414-7110MBK
22.4 Trim Leg, Right 414-7130MBK
22.5 Footer, Right 414-7100MBK
15 Degree Adapter DV-6DLR-E15ADSS
Additional service part numbers appear on following page.
#22 Cast Trim
22.3
22.4
22.5
22.2
22.1
28 7094-803D 12/23
CONTACT INFORMATION
Hearth & Home Technologies
352 Mountain House Road
Halifax, PA 17032
Division of HNI INDUSTRIES
Please contact your Quadra-Fire dealer with any questions or concerns.
For the number of your nearest Quadra-Fire dealer
log onto www.quadrafi re.com
CAUTION
DO NOT
DISCARD
DO NOT DISCARD THIS MANUAL
Important operating
and maintenance
instructions
included.
Read, understand
and follow these
instructions for
safe installation
and operation.
Leave this
manual with party
responsible for
use and operation
of this appliance.
We recommend that you record the following pertinent
information for your heating appliance.
Date purchased/installed:
Serial Number: Location on appliance:
Dealership purchased from: Dealer Phone: 1( ) -
Notes:
This product may be covered by one or more of the following patents: (United States) 5341794, 5263471, 6688302, 7216645, 7047962
or other U.S. and foreign patents pending.
1

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Quadra-Fire Expedition I bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Quadra-Fire Expedition I in de taal/talen: Engels als bijlage per email.

De handleiding is 5.32 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

Andere handleiding(en) van Quadra-Fire Expedition I

Quadra-Fire Expedition I Gebruiksaanwijzing - Français - 28 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info