782206
12
Verklein
Vergroot
Pagina terug
1/26
Pagina verder
-12-
However,this causes the top slide to shift by 0.025 mm to the left
and the same distance to the right.
The chip in the thread is thereforealways only removed from one side.
Once the full thread depth has been reached, afinal full cut is
made by advancing slightly.
Cutting left threads
To cut left threads, the intermediate gear 1(Fig. 21) must be instal-
led between "Z1-Z2"and the leadscrew gear "L1".
In doing so, the turning direction of the leadscrew is reversed. The
support runs from right to left when the chuck is turning clockwise.
Installation and operation areasdescribed above.
Accessories for Lathe PD 250/E
Note:
The described accessories arenot included in the standardequipment.
Installing the centrelathe (No. 24014)
When using acentrefixed to the tailstock, regular lubrication of
the centreand centreboreisnecessary to prevent the temper
from loosening.
Note:
Longer work pieces areclamped between the brad points of the
main spindle and tailstock.
The work piece must have acentreboreonboth faces.
An exact cylindrical work piece is only achieved if the points align
in the horizontal position.
1. Remove three fastening screws from the three-jaw chuck and
remove chuck.
2. Thoroughly clean the fit for the driving disc and centreand its fit
in the main spindle.
3. Insert the centre 4(Fig. 22) in the fit (1) of the main spindle.
4. Fit the driving disc (2) and fasten with three screws (3).
5. Push the lathe carrier 1(Fig. 23) onto the work piece (driving
pin outwards) and tighten the fastening screw (2).
6. On the left side, insert driving pin in one of the three long holes
on the driving disc and the centreinthe centrebore.
7. On the right side, attach the work piece using the tailstock and
fixed or rotating centre.
8. To remove the centre, guide asuitable aluminium or brass rod
through the main spindle from left to right.
9. Hold the centreand release by lightly tapping the rod.
Four-jaw chuck (No. 24036)
In the normal clamping jaw position, only work pieces with an
edge of up to max. 30 mm long can be clamped. The maximum
length is 80 mm in the reverse position.
Larger work pieces arenot securely held. Danger of accident.
Collet chuck unit and collet chucks
Remove mains plug.
Note:
Round, oval, squareand irregularly shaped work pieces can be
clamped as it is possible to adjust the jaws individually.
Centric or eccentric clamping is possible.
Unlike the threejaw chuck, centring of the work piece must be per-
formed manually.
1. Detach the three-jaw chuck and attach the four-jaw chuck.
2. Open the four jaws, clean the contact faces and clamp the
work piece lightly according to visual estimation.
3. Move the support and turning tool onto the plane surface of the
work piece.
4. Turn the chuck by hand to establish symmetrical deviations.
6. Adjust by opening one of the jaws and reset the opposite jaw
accordingly.
7. Tighten all four jaws evenly,alternating crosswise.
Collet set with ER 20 collets (No. 24038)
Important
Always use the correct collet chuck to suit the work piece.
Chucks with an oversized diameter aredestroyed.
Important
Never tighten the union nut when thereisnowork piece inserted.
The collet chuck unit is especially suitable for processing round
parts with great precision. The truth of running is considerably
greater than when working with ajaw chuck.
1. Remove three fastening screws from the threejaw chuck and
remove chuck.
2. Thoroughly clean the fit for the collet chuck mount 2(Fig. 24)
and the fit in the main spindle (1).
3. Attach the collet chuck mount (2) using four fastening screws (3).
4. Insert the collet chuck (6) and loosely screw in the union nut (5).
5. Insert the appropriate work piece in the collet chuck and tighten
the union nut (5) using the tool pins (4).
6. Remove the pins 4(Fig. 24) for tightening the union nut (5)
immediately after tightening.
Fastening the drill chuck (No. 24020)
The jaws (2) must only touch the work piece and must not jam.
Otherwise thereisarisk of the work piece surface becoming
scratched and the motor becoming overloaded.
1. Remove the rotating centrefromthe sleeve. Thoroughly clean
the grease and dirt from the shank taper and chuck bore.
2. Insert the journal in the sleeve and firmly push onto the drill
chuck.
Note:
Releasing the drill chuck is performed in the same way as the
rotating centre.
Fixed steady (No. 24010)
The steady is particularly suitable for hollowing out long work
pieces with diameters up to 40 mm.
1. Release the fastening screw 4(Fig. 25) and position retaining
plate (3) crosswise.
2. Place the steady on the bed guide and set to the required
position.
3. Swivel the retaining plate (3) parallel to the steady base and
tighten fastening screw (4).
12

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Proxxon PD 250-E bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Proxxon PD 250-E in de taal/talen: Engels als bijlage per email.

De handleiding is 3.73 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info