782202
7
Verklein
Vergroot
Pagina terug
1/11
Pagina verder
Motor:
Rotational speed 5,000-22,000/min
Voltage ~230 V, 50/60 Hz
Power consumption 100 W
Noise emission 70dB (A)
Vibration 2.5 m/s2
Please note that the sound and vibration measurements in
particular have been performed with Proxxon bits and cut-
ters. When using third-party brands we cannot guarantee
compliance with the statements given here!
Clamping and changing the bit
Important!
Never work without safety glasses.
Wear a protective mask if large amounts of dust or
harmful dusts accumulate.
Never press the lock button while the device is oper-
ating.
Depending on the collet size, bits and cutters may
have a shaft diameter of max. 3.2 mm.
Insert the tools are far as possible when clamping. En-
sure that the shaft of the tool does not stand out more
than 30 mm from the collet. Excessively protruding
shafts can bend easily and contribute to poor concen-
tricity.
Do not in any case use bits and cutters with an arbour
length of more than 55 mm!
When using collets, always make sure that the collet
chuck and the utilised tool have the same shaft diam-
eter! The arbour of the tool must be seated firmly and
securely in the collet!
Do not work with damaged, bent or worn bits and cut-
ters! Make sure the tools are in perfect condition.
Damaged or worn tools can break and cause injuries!
When storing the bits and cutters, make sure they are
reliably protected from damage!
A correct and consistent speed achieves a high grind-
ing performance, not excessive contact pressure!
By tendency: Bits and cutters with smaller diameters
require higher speeds than those with a larger diam-
eter.
Attention: You absolutely must observe the permissible
maximum speed of the bits and cutters! The tool can
break when the maximum permissible speed is ex-
ceeded. Flying parts can cause damage and severe in-
juries!
1. Slightly turn drill chuck 2(Fig. 2) and simultaneously
press lock button (1) until the latter engages.
2. Open chuck and change bit.
We recommend PROXXON collet chucks for optimal true
running.
Operating instructions
Using the machine
Attention:
Secure the work piece during work! In addition to en-
abling more pleasant and efficient working, it also re-
duces the risk of the workpiece flying about!
Please note: A work piece flying about is a risk for in-
juries! Use a vice or suitable clamping fixture to hold the
work piece!
It is imperative to avoid electric tool recoil!
1. To activate, operate switch 4 (Fig. 1) and set the right
speed for the work on rotational speed adjusting knob
1. Applicable in principle, tools with smaller diameters
must be operated at higher speeds, and tools with
greater diameters at lower speeds in order to achieve
optimal results.
2. When cutting or engraving, hold the machine as if it
were a pen (Fig. 3), being careful not to occlude the
vent slits.
3. For roughing down, grip the machine as if it were a
hammer (Fig. 4).
- 15 -
7

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Proxxon FBS 240-E bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Proxxon FBS 240-E in de taal/talen: Engels als bijlage per email.

De handleiding is 1.04 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info