490692
12
Verklein
Vergroot
Pagina terug
1/88
Pagina verder
12
6 Starting up and using the
machine
Check that the information on the manufacturing
label complies with the actual power supply volt-
age.
Check that the plug type is the same as the socket
type.
6.1 Tightening the stirrer
(see Fig. [2])
Screw in the stirrer [2-4] with endpiece M14x2
(wrench size 22) by turning it to the right in the
adapter ErgoFix [2-1] (wrench size 19) and use
the wrench to tighten it.
Fasten the ErgoFix adapter to the stirrer bar, then
insert the assembled stirrer into the slot of the
spindle. To set-up the working height see chap-
ter 6.5.
6.2 Switching the machine on and off
Always hold the machine with both hands.
Pressing the switch [1-3] puts the machine into
operation and taking your hand away from the
switch stops the machine from working.
Using the switch button to control the speed
(acceleration function switch)
You can use the switch [1-3] to change the level
of the speed until it reaches the speed range that
is set by the speed controller.
Continuous operation
By pressing the switch [1-3] as far as it goes and
pressing the locking switch button [1-4] at the
same time, you can activate continuous operation.
Press and release the switch button [1-3] again to
switch off continuous operation.
6.3 Control electronics
Limiting the starting current
The electronically-controlled soft start ensures that
the machine starts up smoothly.
At the same time, this also prevents the materi-
als to be stirred from spurting out of the mixing
container. Thanks to the low starting current of the
machine, a 10 A fuse is suf cient.
Electronic speed preselection
You can use the speed controller [1-5] to set the
speed:
MXP 1000 EE F, MXP 1200 EE F
Level 1 360 Level 4 520
Level 2 410 Level 5 580
Level 3 470 Level 6 630
MXP 1002 EE F
1st speed 2nd speed
Level 1 360 Level 1 580
Level 2 410 Level 2 670
Level 3 470 Level 3 760
Level 4 520 Level 4 840
Level 5 580 Level 5 930
Level 6 630 Level 6 1010
The speed depends on the stirrer rod that is used
and on the material that you want to process.
Overload protection
An electronic overload protection protects the mo-
tor from damage if there is an extreme overload.
In this case, the motor remains at a standstill and
only starts up again once the load has been re-
moved. To restart the machine, you must switch
it on again.
Constant Electronic function
The Constant Electronic function maintains an al-
most constant speed and load; this ensures that
the material is stirred evenly.
Temperature-dependent overload protection
(VALID for the type MXP 1002 E EF and
MXP 1200 E EF)
To protect the machine against overheating if you
are using it for an extremely prolonged period,
switch the safety electronics to the cooling mode
as soon as the critical temperature is reached. You
cannot load the machine and it runs at a reduced
speed. Approx. 2 minutes after cooling, the ma-
chine is again ready for use and fully able to take
loads.
Protection against re-starting
Prevents the uncontrolled starting of the device
after current supply cut off. For re-starting, the de-
vice must be rst switched off and again switched
on.
6.4 Speed selection switch
(VALID for the type MXP 1002 E EF)
You can use the speed selection switch [1-9] to
preselect two speed ranges:
1st speed 2nd speed
360 – 630 rpm 580 – 1010 rpm
The gears can be switched when the machine is
running down, however not under full load.
6.5 ErgoFix interface
Height setting
The working height of the machine can be indi-
vidually adjusted to achieve an upright working
position.
- Push the casing of the ErgoFix adapter [1-7] in
the direction of the machine to move it as far
as it goes [1-7] and hold it tight.
12

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Protool MXP 1002 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Protool MXP 1002 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Pools, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 12,82 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info