490609
17
Verklein
Vergroot
Pagina terug
1/110
Pagina verder
17
8.1 Free hand according to the
scribe mark
The triangular shape of the splinterguard [4-
3] shows the cutting line of the saw blade
and thus facilitates cutting to a scribe mark.
8.2 Plunge cutting without pilot
drilling
The base runner must be in the front position
for plunge cuts in timber materials (basic
setting, see Figure [1]).
Place saw on the front edge of the runner.
Set saw to maximum no. of strokes and pen-
dulum stroke setting 3 and start the plunge
cut into the workpiece (Figure [6]).
Damaged safety devices and components
must be repaired or replaced in a recognised
specialist workshop, unless otherwise indi-
cated in the operating manual.
To ensure constant air circulation, always
keep the cooling air openings in the motor
housing clean and free of blockages.
Use only original Protool accessories and
Protool consumable material intended for
this machine because these components are
designed specifically for the machine. Using
accessories and consumable material from
other suppliers will most likely affect the
quality of your working results and limit any
warranty claims. Machine wear or your own
personal workload may increase depending
on the application. Protect yourself and your
machine, and preserve your warranty claims
by always using original Protool accessories
and Protool consumable material!
10.1 Parallel guide
Use the parallel guide (order no. 764973) to
guide the jigsaw parallel to the workpiece
edge. The parallel guide can be fitted on both
sides of the base runner:
Slide clamping clip [7-1] onto the base run-
ner from the front.
Insert parallel guide [7-2] through the
clamping clip from the side to the desired po-
sition.
Tighten rotary knob [7-3].
10.2 Circle cutter
The circle cutter (order no. 764969) can be
used to produce circular cuts with a diameter
between 120 and 720 mm. The circle cutter
can be fitted on both sides of the base run-
ner:
Slide clamping clip [7-1] onto the base run-
ner from the front.
Insert circle cutter [7-4] through the clamp-
ing clip from the side to the desired position.
Tighten rotary knob [7-3].
Insert circle tip [7-5] in the rear bore hole of
the circle cutter.
10.3 Saw blades, other accessories
In order to saw different materials quickly
and cleanly, Protool offers saw blades for all
applications that are specially designed for
your Protool jigsaw.
Recommended number of strokes
(adjusting wheel setting)
Hard and soft wood, wood core ply-
wood, plywood, chip board
6
Wood fibre boards 4 - 6
Plastics 3 - 6
Ceramic, aluminium, NF metals 3 - 5
Steel 2 - 4
8 Working with the machine
WARNING
Risk of injury
X
Always secure the workpiece in such a
manner that it cannot move while being
machined.
9 Service and maintenance
WARNING
Risk of injury, electric shock
X
Always disconnect the mains plug from the
socket before performing maintenance
work on the machine!
X
All maintenance and repair work which re-
quires the motor housing to be opened
must only be carried out by an authorised
service workshop.
10 Accessories
17

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Protool JSP 120E bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Protool JSP 120E in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Pools, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 2,52 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info