Handleiding Protool ISP 330 EB (pagina 26 van 182) (Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Pools, Deens, Zweeds, Noors, Fins)

490698

Verklein

Vergroot

Pagina terug

1/182

Pagina verder

tion and prevent an unwanted start-up. When the

machine is turned off, an electric brake activates

and signiﬁ cantly shortens the run-down time of

the chain.

Do not remove the machine from the cutting piece

until the chain is at a standstill.

9.2 Controlling chain and guide bar

lubrication

The quantity of lubricating oil can be controlled

using a feed pump [5-2]. When you press the feed

pump, [5-2] the 0, 1, 2 and MAX positions can be

set at a notch [5-1]. Position 0 ensures minimum

lubrication for clean cuts, but must not be used

permanently, and after such cuts the chain and

plate must be lubricated with an increased quan-

tity. For permanent operation the quantity should

be set to level 2 and MAX.

9.3 Cut indicator

When cutting without the guide rail, adjust the

chain’s internal cutting plane using all of the indi-

cators on the guide runner:

- Indicator 0° [4-1] for rectangular cuts

- For bevel cuts:

• indicator 45° [4-4]

• indicator 60° [4-5]

To determine the chain’s external cutting plane,

use cutting proﬁ le indicators [4-6].

For cutting with the guide rail (GRP 800/1400/

3000-2; Fig. [8]), adjust the chain’s inner cutting

plane using only cut indicator 0° [4-1].

9.4 Guide ruler

Slide the guide ruler [1-3] into the holders in the

runner [1-6] and secure it with the hand screws

[1-5]. The guide ruler allows parallel cuts along

an even edge.

9.5 Exhaust

CAUTION

Inhaled dust may damage respiratory organs.

► During dusty jobs, wear a respiratory mask

and have the machine connected to exhaust

equipment.

To exhaust sawdust or dust, ordinary vacuum clean-

er suction hoses can be connected to the opening

of the rotary exhaust adaptor [1-10].

10 Using accessories

On the bottom part of the suction runner, the ma-

chine has a longitudinal groove for mounting on

the guide rail. Thus larger dimensions can be made

more easily and more precisely.

10.1 The PROTOOL guide system

When cutting larger work pieces, and to achieve ac-

curate angled cuts, use of the GRP 800/1400/3000-2

guide system is recommended for easy and safe

handling.

This allows clean cuts by accurately guiding the

machine along a marked edge. Hard anodising of

the guide bar makes moving the machine even

easier, thus reducing the necessary slide force,

and at the same time makes for a better working

procedure. The saw runner’s side clearance can be

adjusted using the distance screws in the auxiliary

handles [6-1].

10.2 Assembling the guide rail

(GRP 800/1400/3000-2)

The guide rail [7-1] is assembled using special

clamps CL-GRP 300 [7-2] or GRP-Rapid/L [7-5]

to be inserted into the guide grooves designed for

this particular purpose (Fig. [7a]). This allows a

secure hold on uneven surfaces. Anti-slip strips are

attached to the bottom of the guide bar, providing

safe placement and preventing scratches to the

material surface.

CAUTION

If you cut with a tilted saw, the tool and the

clamp bolt with the gripper or with GRP-Rapid/L

may collide.

► Tilt the saw at such an angle only to avoid

collision of the chain with the clamp.

10.3 Assembling the angle guide

(GRP-AG-2)

The combination of the guide rail and the continu-

ously adjustable angle unit [7-3] allows accurate

angular cuts, e. g., for matching ﬁ ts. Mount the

angle unit as shown in Fig. [7b]. You can set the

required cutting angle on the bevel indicator.

10.4 Assembling the connector

(CN-GRP)

Depending on the use and size of the work piece,

multiple guide rails can be jointed together us-

ing a connecting spring [7-4] (Fig. [7c]). For ﬁ rm

connection of multiple guide rails the links can be

afﬁ xed using the screws in the correspondingly

threaded openings.

10.5 Assembling the quick clamp

(GRP-Rapid/L)

The guide rail can be mounted quickly using this

device [7-5] slipped into the bottom groove. A ﬁ rm

mount is achieved by pressing the trigger, and re-

lease is achieved by pressing the stopping but-

ton.

CAUTION

If you cut with the saw at an incline, the tool and

the quick clamp handle may collide.

► The handle of the quick clamp must be turned

to the left towards the material after tighten-

ing, thus preventing the collision even at the

maximum tilt of 60°.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

lees eerst de handleiding door;
controleer of uw vraag al eerder door iemand anders is gesteld;
probeer uw vraag zo duidelijk mogelijk te stellen;
heeft u een probleem en al geprobeerd om dit op te lossen, vermeld dit erbij aub;
heeft u een oplossing gekregen van een bezoeker dan horen wij dat graag in dit forum;
wilt u een reactie geven op een vraag of antwoord, gebruik dan niet dit formulier maar klik op de knop 'reageer op deze vraag';
uw vraag wordt direct op de website gezet; vermijd daarom persoonlijke gegevens in te vullen;

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Protool ISP 330 EB Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info