490702
16
Verklein
Vergroot
Pagina terug
1/134
Pagina verder
16
f) Adjust the riving knife as described
in the operating instructions. Incor-
rect width, position and alignment can be
the cause that the riving knife does not
effectively prevent kickback.
g) Always use the riving knife, except
when performing plunge cuts. After the
plunge cut, mount the riving knife again.
The riving knife interferes when performing
plunge cuts and can lead to kickback.
h) In order for the riving knife to be ef-
fective, it must be located in the cut.
For short cuts, the riving knife is ineffec-
tive for the prevention of kickback.
i) Do not operate the saw with a bent
riving knife. Even a minor malfunction
can lead to sluggish retraction of the re-
tracting blade guard.
5.5 Noise/Vibration Information
Measured values determined according to
EN 60 745.
Typically the A-weighted noise levels of the
tool are:
Sound pressure level: 92 dB (A).
Sound power level: 103 dB (A).
Inaccuracy of measurement K = 3 dB (A).
CAUTION
The noise created during work may
damage hearing.
Use hearing-protective aids!
The typical hand-arm vibration is below
2.5 m/s
2
.
Inaccuracy of measurement K = 1.5 m/s
2
.
6 Commissioning and
Operation
WARNING
Risk of injury, if the tools are used
with wrong supply power.
The voltage speci cations on the rating plate
must correspond with the mains voltage.
Equipment marked with 230 V can also be
connected to 220 V / 240 V.
Check that the plug type is the same as the
socket type.
Adjustment of the riving knife
WARNING
Risk of injury, if the riving knife is not
correctly adjusted.
The riving knife [2-8] must always be used
for safety reasons. The riving knife prevents
the saw blade from becoming jammed when
making lengthwise cuts.
Loosen screw [2-9], adjust the riving knife
[2-8] and retighten the screw (see gure).
2-9
2-8
2.5 – 5 mm
2.5 – 5 mm
Check the function of the swinging guard
[2-7].
Switching On/Off
Switching On:
Press the safety button [1-1].
Press the on-off switch and hold depressed.
Note: The on-off switch cannot be locked on.
Switching Off:
Release the on-off switch [1-2].
7 Adjustment
WARNING
Risk of electric injury.
Before any manipulation with the tool
make sure to unplug the mains socket
outlet.
7.1 Electronic Motor Control
Starting current limiting
The electronically controlled smooth start
takes care that the machine starts without
jerk. As a result of the machine’s reduced
starting current, a 16 A fuse is suf cient.
No-load speed reduction
The electronic control reduces the no-load
speed of the machine which results in re-
duced noise and wear of motor and gear.
16

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Protool CSP85-45 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Protool CSP85-45 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Pools, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 7,48 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info