ENGLISH
WALLAROO QST BABY SEAT
For maximum performance and safety of your new baby seat it is important that you
read this document and follow all instructions provided. The baby seat was designed to
be tted on bicycles with wheels from 26” to 28” diameter and round tubular frame with
Ø 28 up to Ø 35, without a carrier.
KEEP FOR FUTURE REFERENCE
MOUNTING INSTRUCTIONS (see page 2/3)
1M. Wallaroo Baby Seat and components.
2M. Unscrew the big nut lifting simultaneously the red ring.
3M. Rotate the metallic plate and remove the metallic rod.
4M. Make the metallic rod go through the holes of the Wallaroo and put it in one the
3 allowed positions.
5M. Put on the metallic plate and tighten the big nut.
6M. When the big nut is properly fastened, make sure the spring is adjusted to the
groove in the seat and that it does not move.
7M. Put the plastic support block and the metal plate xed around the bicycle tube,
at the highest possible position on the bicycle frame in order to prevent the Wallaroo
evolution, when placed on the bicycle, from touching the bicycle’s wheel.
8M. Start tightening the screws with the longer part of the key in the direction shown
in the picture.
9M. Adjust the screws with the shortest part of the screw driver, so that the support
block does not rotate or slide down the bicycle frame.
Note: After the 1
st
and 2
nd
use, you must verify and rectify the fastening of the screws.
10M. Fit the metallic bracket through the holes of the support block, push the safety
baton inwards.
11M. Adjust the second safety belt to the bicycle frame. The belt must be under
tension.
12M. To remove the wallaroo press the red safety spring and lift the wallaroo.
13M. The seat has a marking of the centre of gravity. After tting the baby seat to the
bicycle, this marking should be a maximum of 10cm behind the rear wheel axle. Make
this adjustment through the alteration of the position of the baby seat in one of the 3
positions available.
FUNCTIONING INSTRUCTIONS (see page 27)
1F. The Wallaroo can function in three dierent positions.
2F. To put it in the desired position unfasten the big nut lifting simultaneously the red
ring and remove metallic plat, metallic rod
3F. Chose one of three positions available.
4F. To remove the buckle of the belt fasten sideways on the red spot.
ENGLISH
5F. Before using the Wallaroo, always adjust the safety belt. The belt must be well
adjusted so it does not hurt the child but keeps her well fastened to the Wallaroo. The
adjustment of the length of the seat belt is done by sliding the belt through the existing
buckles on the front of the Wallaroo.
6F. To regulate the height of the foot rests in relation to the seat bottom and bearing in
mind the size of the child, press the side plates and lift the foot rest as indicated in the
picture ( it may be necessary to apply some pressure).
7F. The foot rests may be adjusted to any of the indicated positions.
8F. To guarantee the safety of your child you must keep the belts of the foot rests always
adjusted. You can do this by removing the belt from the notch and adjust it to the
child’s feet without disturbing or hurting the child.
Maintenance
The maintenance of the baby seat is simple and does not need special care. In any case,
it is advisable to observe the following norms:
- Check regularly the entire xation system of the Wallaroo QST to the bicycle, don’t use
the baby seat if any part is broken;
- Inspect the safety belts and other components to check they are working eectively;
- Inspect the cleanliness of the baby seat from time to time. When dirty, wash with soap
and water (do not use abrasives, corrosives or toxic products);
- The wadding can be washed with lukewarm soapy water. Hung up to dry.
SAFETY INSTRUCTIONS
• The rider must be at least 16 years of age;
• The baby seat is only suitable for transport of children with a maximum weight of 48.5
lbs / 22 kgs, with an age limit of 7 years and check the child’s weight regularly. Do not
carry a child that weighs more than this weight.
• Do not carry a child, who is less than 12 months of age, in this baby seat. To be a
passenger, the child must be able to sit up straight with the head held upright while
wearing a bicycle helmet. A doctor should be consulted about any child who is of
questionable developmental age.
• Check if all parts of the bicycle function correctly with the baby seat mounted.
• Do not install this baby seat on a racing style bicycle (drop handlebar).
• Secure child in baby seat ensuring all safety belts and straps are applied rmly but not
so tight as to cause discomfort to the child;
• Make sure the seat stays slightly reclined towards the back and not towards the
front, to avoid the child from slipping
• The baby seat must never be used before adjusting the safety belt.
• Do not permit any part of the child’s body or clothing, shoelaces, baby seat belts, etc.
to come in contact with moving parts of the bicycle because can be harmful for the
child ore cause accidents.
