519095
3
Verklein
Vergroot
Pagina terug
1/16
Pagina verder
INSTRUCTIONS MANUAL
5.3 Setting the clock
Keep pressing the mode key until the clock symbol appears in the display. Then keep
the mode key pressed down for approx. 8 seconds until the hour display blinks. Then
press the mode key again to increase the hour value. When you have the hour value
desired keep the mode key pressed down for approx. 3 seconds, and the minute
display will start blinking. Repeat the process described above for the hour display
to set the minute value desired. To save the desired time setting, keep the mode key
pressed down for approx. 8 seconds.
You have now completed all your settings and the bicycle computer is ready for use.
5.4 Bicycle computer check
To check that the bicycle computer and sensor have been correctly installed, press
the mode key to activate the display. Ensuring that the computer is fi rmly attached
to the computer mount, turn the front wheel of your bicycle and the speed will
be displayed.
5.5 Restart/Reset
To reset entered and saved data, you have to keep pressing the mode key until the
ODO display appears. Then keep the mode key pressed down for approx. 6 seconds,
and repeat the settings (refer to section 5.1).
5.6 Automatic starting/stopping of readings
You don’t have to switch on the bicycle computer each time before use (in time
display). When you start riding, all the readings will automatically start until the
bicycle comes to rest. The bicycle computer will automatically switch to power saving
mode, if the bicycle is not in use for a period longer than 10 minutes.
6. MODES/FUNCTIONS
After starting up the bicycle computer, the display will show the speed and time.
Speed: is continuously calculated and updated, and shown in the upper part of the
display. Measuring range: 0.1 – 99.9
Press the mode key to switch between the following modes:
DO (total distance travelled):
All kilometres (miles) travelled will be stored.
Maximum memory: 19,999.9
MAX (maximum speed):
The maximum speed attained will be stored.
Maximum memory: 199.9
AVG (average speed)
Maximum memory: 99.9
The “ERR” symbol will appear, if TM exceeds 100 hrs or DST exceeds 1,000 km.
The clock symbol (time)
SCAN (Scan function):
Rolling function display: keep pressing the mode key until you reach the SCAN
mode. The word SCAN will appear in the display. In this mode, the DST, time, TM,
AVG, MAX and ODO functions will automatically be displayed in approx. 4
second intervals.
TM (journey time / journey chronometer):
Automatically started when journey begins.
Maximum memory: 19 hrs 59 min 59 sec
DST (journey distance):
Automatically started when journey begins.
Maximum memory: 999.9
6.1 Resetting the route data (DST, TM, AVG, MAX) to zero
Press the mode key to display (DST). Then press the mode key again and keep
pressed down for approx. 3 seconds. The 4 route data readings (journey distance,
journey time, average speed and maximum speed) will be reset to zero.
7. REPLACING THE BATTERIES
7.1 Bicycle computer
Unscrew the lid of the battery compartment (located on the underside of the bicycle
computer) using a coin. Insert the battery so that the plus pole (+) is visible. Replace
the lid and screw shut. After the batteries are inserted, all the settings must be
repeated (refer to section 5.2 Setting the tyre size).
10. WARRANTY PROVISIONS
Bicycle computer article no.: 0526
This bicycle computer is provided with a 2-year warranty. The warranty period starts
from the date of purchase (purchase receipt, proof of purchase). During the warranty
period, address any complaints you may have to your dealer or the service address
provided below. During this period we will correct free of charge all faults caused by
material defects or malfunctioning.
Batteries, defects caused by improper handling, a fall, impact and the like are
excluded from the warranty. Please note that the warranty period is not affected by
any repair or replacement. The 2-year warranty period starting from the purchase
date shall remain in effect.
After the warranty period has expired, you will still be able to send the defective
bicycle computer to the service address provided below to be repaired. Any repairs
caused after the warranty period has expired are, however, subject to charge. After
prior telephone contact, please send your properly packaged bicycle computer (with
your purchase receipt) with suffi cient postage to the following address:
Prophete GmbH u. Co. KG
Lindenstrasse 50
D-33378 Rheda-Wiedenbrück
Phone: +49 (0) 5242 4108-59
Fax: +49 (0) 5242 4108-73
Email address: service@prophete.net
Website: www.prophete.de
5. INITIAL OPERATION
We recommend that you fi rst carefully read the operating instructions, before using
the bicycle computer the fi rst time.
5.1 Switching on the bicycle computer for the fi rst time
Before you can use the bicycle computer for the fi rst time, you must make a few
settings. Insert the battery (refer to section 7.1). If the battery is already inserted, or
you want to change any settings, press the reset key on the back of the computer.
This will automatically test the LCD segments. Press the mode key to end the test.
Now “KM/h” will blink. If you want to change to M/h press the mode key. Then keep
the mode key pressed down until the fi rst digit for the tyre size setting blinks (refer
to table 5.2). You can now increase the number by briefl y pressing the mode key.
When the value you want appears, hold the mode key down – the next digit will
then start blinking. Repeat this process until you have set all the numbers correctly.
You now have another opportunity to set kilometres or miles – briefl y press the
mode key to set miles. Keep the mode key pressed down for approx. 3 seconds to
save your setting.
5.2 Setting the tyre size
After inserting the battery (section 7.1) or changing the tyre size, you have to repeat
the procedure described in section 5.1.
Determining the tyre size: mark the front tyre and the ground at the same spot, or
alternatively, use the valve for orientation. Rotate the wheel through one revolution
and measure the distance covered in cm. This is your entry value. Or alternatively,
use the table below for orientation.
8. DECLARATION OF CONFORMITY
It is hereby confi rmed that the designated product conforms to the fundamental
requirements of the following European guidelines:
2004/108/EG EMV guideline
European Parliament and Council guideline from 15.12.2004
2006/95/EG Low voltage guideline
European Parliament and Council guideline from 12.12.2006
The conformity of this product with the guidelines is established by its full compli-
ance with the harmonised and non-harmonised standards.
½
9. DESCRIPTION OF ERRORS
In the event of an error occurring, please check the following points fi rst, before you
make any complaint about the bicycle computer.
Speed not displayed
Check for correct magnet/sensor alignment
• Check batteries
The display will not work if the batteries are too weak
Incorrect speed reading, or speed is displayed when not in motion,
or maximum speed display is too high
Check that you have the right setting for the tyre size
Check that you have the right km/miles setting
Check that magnet and sensor are correctly positioned
It is possible that unknown atmospheric or RF disturbances, atmospheric or
radio interferences, high-voltage power lines, railway lines etc. may also cause
an incorrect speed display.
No display (blacked out)
Too high temperature, or display is exposed to direct sunlight. Display will return to
normal when cooled off.
Display shows erratic numbers
Remove bicycle computer battery and reinsert.
No display
Check the batteries
Check that the batteries are inserted the right way round (+/-).
BICYCLE COMPUTER
OPERATING INSTRUCTIONS
Art. No.: 0526 | 8 Functions
0526_layout_en.indd 10526_layout_en.indd 1 10.08.2011 8:49:13 Uhr10.08.2011 8:49:13 Uhr
3

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Prophete 0526 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Prophete 0526 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans als bijlage per email.

De handleiding is 1,59 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info