Handleiding Profile PLI-151 (pagina 8 van 13) (Nederlands, Duits, Engels, Frans, Italiaans, Spaans)

566834

Verklein

Vergroot

Pagina terug

1/13

Pagina verder

LAMP WITH ENERGY-SAVING LIGHT EN - 1

PLI-145-PLI151

We thank you for the purchase of this Profile product.

Note: It is important that you read this manual carefully

before using the product and be sure to save this

manual for possible use later.

Note

Check if building regulations apply to your area

whereby you must have the lamp installed by an

accredited electrician. An electrician can give you

information about correct wiring. Never install the fitting

outside in rainy weather.

SWITCH OFF THE POWER BEFORE YOU INSTALL

THE LAMP.

Correct mounting

 With installation outside preferably choose a place

under a roof. Pay attention to the recommandations

in fig. 2

 To avoid malfunctions, do not aim the sensor to:

o Warmth sources (e.g. the sun, BBQ ...)

o Strong magnetic fields

o Reflecting surfaces (e.g. white walls,

swimming pools)

 The detection specifications can vary according to

altitude and place of assembly as well as

temperature oscillations.

 Before determinating the place of installation, be

aware that movement straight through the detection

area works more effectively than movement directly

to or away from the sensor. (fig. 4)

Correct installation

 Connect the lamp to a circuit with wall switch.

 Unscrew the stainless steel bolts (fig 1.1) on the side

to take the holder (fig 1.2) from the fitting.

 Fix the holder to the wall with 2 screws.

 Fix the lamp back on the assembled holder and

adjust the light direction as you prefer.

 Remove the cover of the cable connection (fig 1.3).

 Untie the nut (fig 1.4) and the additional attachment

(fig 1.5) and pull the power supply wires through the

opening with the rubber packing.

 The lamp must be connected to mains voltage of

230V, max. fusing 16A.

 Connect the wires according to figure 3.

 Fix the cable connection cover, the nut and the

additional attachment.

 Remove the protection glass in front (fig 1.6) and

insert the included bulb. Then fix the glass again.

 Always respect the instructions on the identification

label of the connected power cables.

 Other uses than described above can cause damage

to the product and increase the risk of short-circuit,

fire, electric shocks, etc.

 The product may not be adapted as a whole. The

safety instructions must be strictly observed.

 The product may not be adapted as a whole. The

safety instructions must be strictly observed.

 Setting the functions (fig 5)

1) Setting the light intensity (lux)

With the LUX Switch you adjust the working of the

sensor to match the intensity of the ambient light.

If the arrow is pointing to the sun the sensor responds

in both daylight and at night.

If the arrow is pointing to the moon the sensor will only

respond at night.

In between the sensor responds in half-light.

2) Setting the lighting time (TIME)

With this adjusting knob you can set the period of the

light staying on after switching on. You can set the

time from 10 sec. to 4 min.

3) Setting the sensitivity (SENS)

With this switch you can stipulate how sensitive the

sensor reacts to movement.

Safety instructions

 The importer accepts no responsibility for damage

claims with respect to objects or persons that result

from incorrect use or non-compliance with the safety

instructions. Any damage claims in such cases will

be declared null and void.

 When replacing the energy-saving bulb:

o the power supply must be switched

off.

o Do not exceed the maximum wattage

of 32W.

o Let the floodlight cool down

 Always replace cracked or broken glass by glass

with the same properties as the original glass.

Technical information

 Working voltage: 220-240V~50Hz

 Maximum lamp power:

o PLI-145: 23W.

o PLI151: 2x23W

 Maximum current strength: 10/16A.

 Dustproof and splashproof: IP44.

 Passive infrared sensor (PIR)

 Sensor angle: 180°

 Sensor range: 20 m.

 Lighting time: +/-10 sec. – 4 min.

Maintenance

 Only use a dry, soft cloth for cleaning the lamp.

 Never immerse the lamp in water.

 Maintenance and repairs may only be carried out by

technicians who are familiar with any applicable

regulations.

Guarantee conditions

The guarantee period for PLI-145/PLI-151 amounts to

2 years and commences on the date of purchase.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

lees eerst de handleiding door;
controleer of uw vraag al eerder door iemand anders is gesteld;
probeer uw vraag zo duidelijk mogelijk te stellen;
heeft u een probleem en al geprobeerd om dit op te lossen, vermeld dit erbij aub;
heeft u een oplossing gekregen van een bezoeker dan horen wij dat graag in dit forum;
wilt u een reactie geven op een vraag of antwoord, gebruik dan niet dit formulier maar klik op de knop 'reageer op deze vraag';
uw vraag wordt direct op de website gezet; vermijd daarom persoonlijke gegevens in te vullen;

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Profile PLI-151 Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info