722008

Pride Colt Series Handleiding

43
Verklein
Vergroot
Pagina terug
1/48
Pagina verder
*INFMANU3627*
COLT
SERIES
Including Models: Colt Plus, Colt Nine, Colt Deluxe, Colt Sport and Colt Twin
Copyright © 2011
Pride Mobility Products Ltd.
INFMANU3627/Rev G/November 2011
SAFETY GUIDELINES
NOTE: This owner’s manual is compiled from the latest specifications and product information avail-
able at the time of publication. We reserve the right to make changes as they become necessary. Any
changes to our products may cause slight variations between the illustrations and explanations in this
manual and the product you have purchased. The latest/current version of this manual is available on
our website.
Pride Dealer:
Address:
Phone Number:
Purchase Date: Serial Number:
WARNING! An authorised Pride Dealer or qualified technician must perform the initial
setup of this scooter and must perform all of the procedures in this manual.
The symbols below are used throughout this owner's manual and on the scooter to identify warnings and
important information. It is very important for you to read them and understand them completely.
WARNING! Indicates a potentially hazardous condition/situation. Failure to follow
designated procedures can cause either personal injury, component damage or
malfunction. On the product, this icon is represented as a black symbol on a yellow
triangle with a black border.
MANDATORY! These actions should be performed as specified. Failure to perform
mandatory actions can cause personal injury and/or equipment damage. On the product,
this icon is represented as a white symbol on a blue dot with a white border.
PROHIBITED! These actions are prohibited. These actions should not be performed at
any time or in any circumstances. Performing a prohibited action can cause personal
injury and/or equipment damage. On the product, this icon is represented as a black
symbol with a red circle and a red slash.
Please fill out the following information for quick reference:
3
Colt Series www.pridemobility.com
CONTENTS
I. INTRODUCTION ...................................................................................................................... 4
II. SAFETY ........................................................................................................................................ 5
III. YOUR SCOOTER ..................................................................................................................... 19
IV. BATTERIES AND CHARGING ......................................................................................... 24
V. OPERATION ............................................................................................................................. 29
VI. COMFORT ADJUSTMENTS .............................................................................................. 31
VII. DISASSEMBLY AND ASSEMBLY .................................................................................. 35
VIII.BASIC TROUBLESHOOTING ........................................................................................... 37
IX. CARE AND MAINTENANCE ............................................................................................. 39
X. WARRANTY ............................................................................................................................. 42
4
www.pridemobility.com Colt Series
I. INTRODUCTION
SAFETY
Welcome to Pride Mobility Products (Pride). The product you have purchased combines state-of-the-art
components with safety, comfort and styling in mind. We are confident the design features will provide
you with the conveniences you expect during your daily activities. Understanding how to safely operate
and care for this product should bring you years of trouble free operations and service.
Read and follow all instructions, warnings and notes in this manual and all other accompanying literature
before attempting to operate this product for the first time. You must also read all instructions, warnings
and notes contained in any supplemental instructional booklets that accompanied your scooter before
initial operation. In addition, your safety depends upon you, as well as your dealer, carer or healthcare
professional in using good judgement.
If there is any information in this manual which you do not understand or if you require additional
assistance for setup or operation, please contact your authorised Pride Dealer. Failure to follow the
instructions, warnings and notes in this manual and those located on your Pride product can result
in personal injury or product damage and will void Pride’s product warranty.
PURCHASER’S AGREEMENT
By accepting delivery of this product, you promise that you will not change, alter or modify this product
or remove or render inoperable or unsafe any guards, shields or other safety features of this product; fail,
refuse or neglect to install any retrofit kits from time to time provided by Pride to enhance or preserve the
safe use of this product.
SHIPPING AND DELIVERY
Before using your scooter, make sure your delivery is complete as some components may be individually
packaged. If you do not receive a complete delivery, please contact your authorised Pride Dealer
immediately. Where damage has occurred during transport, either to the packaging or content, please
contact the delivery company responsible.
INFORMATION EXCHANGE
We want to hear your questions, comments and suggestions about this manual. We would also like to hear
about the safety and reliability of your new scooter and about the service you received from your
authorised Pride Dealer. Please notify us of any change of address, so we can keep you apprised of
important information about safety, new products and new options that can increase your ability to use and
enjoy your scooter. Please feel free to contact us at the address below:
Pride Mobility Products Ltd.
32 Wedgwood Road
Bicester, Oxon OX26 4UL
NOTE: If you ever lose or misplace your product registration card or your copy of this manual, contact
us and we will be glad to send you a new one immediately.
5
Colt Series www.pridemobility.com
II. SAFETY
PRODUCT SAFETY SYMBOLS
The symbols below are used on the scooter to identify warnings, mandatory actions and prohibited actions.
It is very important for you to read and understand them completely.
Pinch/Crush points created during assembly.
Corrosive chemicals contained in battery.
EMI/RFI - This product has been tested and passed at an immunity level of 20 V/m.
Explosive conditions exist!
Read and follow the information in the owner’s manual.
Maximum seating weight.
Indicates tie-down points on the scooter.
Indicates electrical shock hazard.
6
www.pridemobility.com Colt Series
II. SAFETY
Place unit on level ground and stand to one side when changing from drive mode
to freewheel mode or freewheel mode to drive mode.
Locked and in drive mode.
Unlocked and in freewheel mode.
Do not remove anti-tip wheels.
Battery posts, terminals and related accessories contain lead and lead
compounds. Wear goggles and gloves when handling batteries and wash hand
after handling.
Do not use a cell phone, walkie/talkie, laptop or other radio transmitter while
operating.
Avoid exposure to rain, snow, ice, salt or standing water whenever possible.
Maintain and store in a clean and dry condition.
Do not expose to heat sources such as open flame or sparks. Do not transport
batteries with flammable or combustible items.
Do not place the scooter in freewheel mode when on an incline or decline.
7
Colt Series www.pridemobility.com
II. SAFETY
Removal of grounding prong can create electrical hazard. If necessary, properly
install an approved 3-pronged adapter to an electrical outlet having 2-pronged
plug access.
Do not connect an extension lead to the AC/DC converter or the battery charger.
Keep tools and other metal objects away from battery terminals. Contact with
tools can cause electrical shock.
Do not allow unsupervised children to play near the scooter while the batteries
are charging.
Do not use batteries with different amp-hour (Ah) capacities. Do not mix old and
new batteries. Always replace both batteries at the same time.
Keep your hands away from the tyres when driving. Be aware that loose fitting
clothing can become caught in drive tyres.
Battery charger for indoor use only.
Do not mix AGM or Gel-Cell batteries. Always use batteries of the same type and
chemistry.
8
www.pridemobility.com Colt Series
Scooter does not conform to ISO 7176-19 for transport of an occupied scooter in
a motor vehicle.
II. SAFETY
Disposal and recycling - Contact your authorised Pride Dealer for information on
proper disposal and recycling of your Pride product and its packaging.
Manufactured in.
Scooter information label.
FRONT SHROUD
Battery Set Configuration:
+ = Positive (Red) Terminal Post
- = Negative (Black) Terminal Post
Connect Red wires to Red Positive (+) Terminal Posts.
Connect Black wire to Black Negative (-) Terminal Posts.
Use only AGM or Gel-Cell batteries to reduce the risk of leakage or explosive
conditions.
9
Colt Series www.pridemobility.com
II. SAFETY
GENERAL
MANDATORY! Do not operate your new scooter for the first time without completely
reading and understanding this owner’s manual.
Your scooter is a state-of-the-art life-enhancement device designed to increase mobility. Pride provides an
extensive variety of products to best fit the individual needs of the scooter user. Please be aware that the
final selection and purchasing decision regarding the type of scooter to be used is the responsibility of the
scooter user, who is capable of making such a decision and his/her healthcare professional (i.e., medical
doctor, physical therapist, etc.).
The contents of this manual are based on the expectation that a mobility device expert has properly fitted
the scooter to the user and has assisted the prescribing healthcare professional and/or the authorised Pride
Dealer in the instruction process for the use of the product.
There are certain situations, including some medical conditions, where the scooter user will need to
practice operating the scooter in the presence of a trained attendant. A trained attendant can be defined as
a family member or care professional specially trained in assisting a scooter user in various daily living
activities.
As you begin using your scooter during daily activities, you will probably encounter situations in which
you will need some practice. Simply take your time and you will soon be in full and confident control as
you maneouver through doorways, on and off lifts, up and down ramps and over moderate terrain.
Below are some precautions, tips and other safety considerations that will help you become accustomed
to operating the scooter safely.
MODIFICATIONS
Pride has designed and engineered your scooter to provide maximum mobility and utility. A wide range
of accessories is available from your authorised Pride Dealer to further customise your scooter to better
suit your needs and/or preferences. However, under no circumstances should you modify, add, remove or
disable any feature, part or function of your scooter.
WARNING! Do not modify your scooter in any way not authorised by Pride. Do not use
accessories if they have not been tested or approved for Pride products.
REMOVABLE PARTS
WARNING! Do not attempt to lift or move your scooter by any of its removable parts,
including the armrests, seat or shroud. Pride recommends use of only solid, non-
removable frame components such as scooter securement points or the front and rear
frame weldments to lift or move your scooter.
WARNING! Lifting the scooter should be accomplished with no fewer than three people,
one at the front and two at the rear of the unit.
PRE-RIDE SAFETY CHECK
Get to know the feel of your scooter and its capabilities. Pride recommends that you perform a safety check
before each use to make sure your scooter operates smoothly and safely.
10
www.pridemobility.com Colt Series
II. SAFETY
Perform the following inspections prior to using your scooter:
Check for proper tyre inflation. Maintain but do not exceed the psi/bar/kPa air pressure rating indicated
on each tyre if equipped with pneumatic tyres.
Check all electrical connections. Make sure they are tight and not corroded.
Check all harness connections. Make sure they are secured properly.
Check the brakes.
Check battery charge.
If you discover a problem, contact your authorised Pride Dealer for assistance.
TYRE INFLATION
If your scooter is equipped with pneumatic tyres, you should check or have the air pressure checked at least
once a week. Proper inflation pressures will prolong the life of your tyres and help ensure the smooth
operation of your scooter.
WARNING! It is critically important that the psi/bar/kPa air pressure rating indicated on
each tyre be maintained in pneumatic tyres at all times. Do not underinflate or overinflate
your tyres. Low pressure may result in loss of control and overinflated tyres may burst.
Failure to maintain the psi/bar/kPa air pressure rating indicated on the pneumatic tyres
at all times may result in tyre and/or wheel failure.
WARNING! Inflate your scooter tyres from a regulated air source with an available
pressure gauge. Inflating your tyres from an unregulated air source could overinflate
them, resulting in a burst tyre.
NOTE: If the tyres on your scooter list the psi rating only, use the following conversion formulas to find
the bar or kPa rating: bar = psi x 0.06895; kPa = psi x 6.89476.
WEIGHT LIMITATIONS
Your scooter is rated for a maximum weight capacity. Refer to the specifications table for information.
Keep in mind that the maximum weight capacity includes the combined weight of the user and any
accessories mounted to the scooter.
MANDATORY! Stay within the specified weight capacity for your scooter. Exceeding the
weight capacity voids your warranty. Pride will not be held responsible for injuries and/
or property damage resulting from failure to observe weight limitations.
WARNING! Do not carry passengers on your scooter. Carrying passengers on your
scooter may affect the centre of gravity, resulting in a tip or a fall.
INCLINE INFORMATION
More and more buildings have ramps with specified degrees of inclination, designed for easy and safe
access. Some ramps may have turning switchbacks (180-degree turns) that require you to have good
cornering skills on your scooter.
Proceed with extreme caution as you approach the downgrade of a ramp or other incline.
Take wide swings with your scooter around any tight corners. If you do that, the scooter’s rear wheels
will follow a wide arc, not cut the corner short and not bump into or get hung up on any railing corners.
When driving down a ramp, keep the scooter’s speed adjustment set to the slowest speed setting to
ensure a safely controlled descent.
Avoid sudden stops and starts.
11
Colt Series www.pridemobility.com
When climbing an incline, try to keep your scooter moving. If you must stop, start up again slowly and
then accelerate cautiously. When driving down an incline, do so by setting the speed adjustment dial to the
slowest setting and driving in the forward direction only. If your scooter starts to move down the incline
faster than you anticipated or desired, allow it to come to a complete stop by releasing the throttle control
lever. Then push the throttle control lever forward slightly to ensure a safely controlled descent.
WARNING! When on any sort of an incline or decline, never place the scooter in
freewheel mode, especially when seated on it or standing next to it.
WARNING! When climbing an incline, do not zigzag or drive at an angle up the face
of the incline. Drive your scooter straight up the incline. This greatly reduces the
possibility of a tip or a fall. Always exercise extreme caution when negotiating an
incline.
WARNING! Do not drive your scooter across the side of an incline or diagonally up
or down an incline; do not stop, if possible, while driving up or down an incline.
WARNING! You should not travel up or down a potentially hazardous incline (i.e.,
areas covered with snow, ice, cut grass or wet leaves).
WARNING! Even though your scooter is capable of climbing slopes greater than
those listed in the Product Specifications Sheet, do not, under any
circumstances, exceed the incline guidelines or any other specifications. Doing
so could cause instability in your scooter.
Handicap public access ramps are not subject to government regulation in all countries and therefore do
not necessarily share the same standard percent of slope. Other inclines may be natural or, if man-made,
not designed specifically for scooters.
Tests were conducted with the scooter’s seat in the highest position and adjusted rearward on the seat base
to its farthest rearward position. Use the specification information as a guideline. Your scooter’s ability to
travel up inclines is affected by your weight, your scooter’s speed, your angle of approach to the incline
and your scooter setup.
WARNING!
Any attempt to climb or descend a slope steeper than what is listed in the
Product Specifications may put your scooter in an unstable position and cause it to tip.
WARNING! Never carry an oxygen tank weighing more than 6.8 kg (15 lbs.). Never fill the
front or rear basket with contents exceeding 6.8 kg (15 lbs.).
When you approach an incline, it is best to lean forward. See figures 1 and 2. This shifts the centre of
gravity of you and your scooter toward the front of the scooter for improved stability.
NOTE: When negotiating ramps, if the throttle control lever is released while moving forward, the
powered scooter may "roll back" approximately 30.5 cm (1 foot) before the brake engages. If the
throttle control lever is released while moving in reverse, the powered scooter may "roll back"
approximately 1 metre (3 feet) before the brake engages.
II. SAFETY
12
www.pridemobility.com Colt Series
II. SAFETY
Figure 2. Increased Stability Driving Position
Figure 1. Normal Driving Position
CORNERING INFORMATION
Excessively high cornering speeds can create the possibility of tipping. Factors which affect the possibility
of tipping include, but are not limited to, cornering speed, steering angle (how sharply you are turning),
uneven road surfaces, inclined road surfaces, riding from an area of low traction to an area of high traction
(such as passing from a grassy area to a paved area – especially at high speed while turning) and abrupt
directional changes. High cornering speeds are not recommended. If you feel that you may tip over in a
corner, reduce your speed and steering angle (i.e., lessen the sharpness of the turn) to prevent your scooter
from tipping.
WARNING! When cornering sharply, reduce your speed and maintain a stable centre of
gravity. When using your scooter at higher speeds, do not corner sharply. This greatly
reduces the possibility of a tip or fall.
OUTDOOR DRIVING SURFACES
Your scooter is designed to provide optimum stability under normal driving conditions—dry, level
surfaces composed of concrete, blacktop or tarmac. However, Pride recognises that there will be times
when you will encounter other surface types. For this reason, your scooter is designed to perform
admirably on packed soil, grass and gravel. Feel free to use your scooter safely on lawns and in park areas.
Avoid driving on uneven terrain and/or soft surfaces.
Avoid tall grass that can become tangled in the running gear.
Avoid loosely packed gravel and sand.
Do not use your scooter in fresh or salt water.
Do not use your scooter at the edge of a steam, lake or ocean.
If you feel unsure about a driving surface, avoid that surface.
PUBLIC STREETS AND ROADWAYS
WARNING! Exercise extreme caution when operating the scooter on footpaths,
pavements, bridleways, pedestrian areas and roads. Obey all local pedestrian traffic rules.
13
Colt Series www.pridemobility.com
II. SAFETY
BRAKING INFORMATION
Your scooter is equipped with these powerful brake systems:
Regenerative: Uses electricity to rapidly slow the vehicle when the throttle control lever returns to the
centre/stop position.
Disc Park Brake: Activates mechanically after regenerative braking slows the vehicle to near stop or
when power is removed from the system for any reason.
(Optional) Handbrake: This lever provides you with emergency stopping power. See III. “Your
Scooter.”
HANDBRAKE LEVER (OPTIONAL FEATURE - COLT SPORT ONLY)
The handbrake lever contains hydraulic fluid. When the lever is depressed, the fluid is pushed through the
brake line to engage the brake pads against the brake discs. The handbrake lever is a completely sealed
unit, meaning that the hydraulic fluid should not leak; however, there are certain safety measures that
should be taken if the handbrake lever becomes cracked or damaged.
Do not touch spilled material unless wearing protective equipment, such as safety goggles and gloves.
For small spills, cover the material with dry earth, sand or other non-combustible absorbent material.
Once absorbed, enclose the material in a plastic bag and contact your local waste disposal agency for
proper disposal measures. Do not expose the material to waterways or sewers.
If the eyes are exposed, check for and remove contact lenses. Flush eyes with cool, clean, low-
pressure water while occasionally lifting and lowering the eyelids. Seek medical attention if excessive
tearing, redness or pain persists.
If the skin is exposed, remove all contaminated clothing. Wipe off excess material and wash exposed
skin with soap and water. Seek medical attention if skin appears damaged or if irritation persists.
Thoroughly clean contaminated clothing before reuse. Discard contaminated leather goods.
If ingested, do not induce vomiting or give anything to drink unless directed to by a physician. Never
give anything by mouth to a person who is not fully conscious. Seek medical attention immediately.
If inhaled, move the affected individual to fresh air. If the affected individual is not breathing,
immediately begin rescue breathing. If breathing is difficult, 100% humidified oxygen should be
administered by a qualified individual. Seek medical attention immediately and keep the affected
individual warm and at rest.
If ignited, use dry chemical, foam, carbon dioxide or water fog to extinguish.
WARNING! Do not modify the handbrake lever or attempt to replace the hydraulic fluid.
If damage occurs, follow the safety information in this section and contact your
authorised Pride Dealer for handbrake replacement. The hydraulic handbrake should
only be serviced or replaced by your authorised Pride Dealer.
WARNING! The handbrake contains hydraulic fluid that can cause mild skin, eye and
nasal/bronchial irritation. Do not attempt to adjust or service the handbrake without
proper protective equipment such as safety goggles and gloves and wash hands after
handling.
14
www.pridemobility.com Colt Series
GETTING ONTO AND OFF OF YOUR SCOOTER
Getting onto and off of your scooter requires a good sense of balance. Please observe the following safety
tips when getting onto and off of your scooter:
Remove the key from the key switch.
Ensure that your scooter is not in freewheel mode. See III. “Your Scooter.”
Make certain that the seat is secured into place.
Pivot the armrests up to make getting onto and off of the scooter easier.
WARNING! Position yourself as far back as possible in the scooter seat to prevent the
scooter from tipping.
WARNING! Avoid putting all of your weight on the scooter armrests and do not use the
armrests for weight bearing purposes, such as transfers. Such use may cause the
scooter to tip, resulting in a fall from the scooter and personal injury.
WARNING! Avoid putting all of your weight on the floorboard. Such use may cause the
scooter to tip.
KERB
II. SAFETY
STATIONARY OBSTACLES (STEPS, KERBS, ETC.)
WARNING! Do not drive near raised surfaces, unprotected ledges and/or drop-offs (kerbs,
porches, stairs, etc.).
WARNING! Do not attempt to have your scooter climb or descend an obstacle that is
inordinately high.
WARNING! Do not attempt to have your scooter proceed rearward down any step, kerb
or other obstacle. This may cause the scooter to tip.
WARNING! Be sure your scooter is traveling perpendicular to any kerb you may be
required to ascend or descend. See figures 3 and 3A.
WARNING! Even though your scooter may be capable of handling greater obstacles, Pride
recommends that you do not attempt to negotiate a kerb that has a height greater than
5 cm (2 in.). Doing so could cause instability in your scooter.
Figure 3. Correct Kerb Approach
Figure 3A. Incorrect Kerb Approach
KERB
15
Colt Series www.pridemobility.com
II. SAFETY
INCLEMENT WEATHER PRECAUTIONS
Exposure of your scooter to inclement weather conditions should be avoided whenever possible. If
suddenly caught up in rain, snow, severe cold or heat while operating your scooter, proceed to shelter at
the earliest opportunity. Thoroughly dry your scooter before storing, charging or operating your scooter.
PROHIBITED! Operating in rain, snow, salt, mist/spray conditions and on icy/slippery
surfaces can have an adverse effect on the electrical system. Maintain and store your
scooter in a dry and clean condition.
WARNING! Prolonged exposure to hot or cold conditions may affect the temperature of
upholstered and non-upholstered items on the scooter, possibly resulting in skin
irritation. Exercise caution when using your scooter in extremely hot or cold conditions
or when exposing your scooter to direct sunlight for prolonged periods of time.
FREEWHEEL MODE
Your scooter is equipped with a manual freewheel lever that, when engaged, allows the scooter to be
pushed. For more information about how to place your scooter into and out of freewheel mode, see III.
“Your Scooter.”
WARNING! When your scooter is in freewheel mode, the braking system is disengaged.
Disengage the drive motors only on a level surface.
Ensure the key is removed from the key switch.
Stand to the side of the scooter to engage or disengage freewheel mode. Never sit on
a scooter to do this.
After you have finished pushing your scooter, always return it to the drive mode to
lock the brakes.
An added feature built into the scooter is “push-too-fast” protection which safeguards the scooter against
gaining excessive speed while in freewheel mode.
“Push-too-fast” operates differently depending on which of two conditions exists:
If the key is switched “off” while in freewheel mode, the scooter’s controller activates regenerative
braking when the scooter is pushed faster than a maximum threshold which has been preprogrammed.
In this case, the controller is acting as a speed governor.
If the key is switched “on” while in freewheel mode, you will encounter considerable resistance at any
speed. This prevents the scooter from gaining unwanted momentum should the manual freewheel lever
inadvertently be released while driving the scooter.
WARNING! Pride recommends that you do not disconnect the batteries when the scooter
is in freewheel mode as this may interfere with the function of the controller.
DOORS
Determine if the door opens toward or away from you.
Use your hand to turn the knob or push the handle or push-bar.
Drive your scooter gently and slowly forward to push the door open. Or drive your scooter gently and
slowly rearward to pull the door open.
16
www.pridemobility.com Colt Series
II. SAFETY
STAIRS AND ESCALATORS
Scooters are not designed to travel up or down stairs or escalators. Always use a lift.
WARNING! Do not use your scooter to negotiate steps or escalators.
LIFTS
Modern lifts have a door edge safety mechanism that, when pushed, reopens the door(s).
If you are in the doorway of a lift when the door(s) begin to close, push on the rubber door edge or
allow the rubber door edge to contact the scooter and the door will reopen.
Use care that handbags, packages or scooter accessories do not become caught in lift doors.
NOTE: If your scooter’s turning radius is greater than 152.4 cm (60 in.), it may be difficult to maneouver
in lifts and building entrances. Use caution when attempting to turn or maneouver your scooter in small
spaces and avoid areas that might pose a problem.
LIFT SYSTEMS/ELEVATION PRODUCTS
If you will be transporting your scooter during travel, you may find it necessary to use a vehicle-
mounted lift system or elevation product to aid in transportation. Pride recommends that you closely
review the warnings, instructions, specifications and safety information set forth by the manufacturer
of the lift/elevation product before using that product.
WARNING! Not all lift systems/elevation products are rated for use with an occupied
mobility device. Pride recommends that you do not remain seated in your scooter when
it is being used in connection with any type of lift system/elevation product unless:
That product is rated for occupied use by the manufacturer.
You are able to occupy your mobility device in strict conformity with the warnings,
instructions, specifications and safety guidelines set forth by the manufacturer.
WARNING! Always turn off the power to the scooter when you are being transferred via
an elevation product. Failure to do so may result in accidental throttle control lever
contact, resulting in unintended movement and personal injury or product damage.
BATTERIES
In addition to following the warnings below, be sure to comply with all other battery handling information.
MANDATORY! Battery posts, terminals and related accessories contain lead and
lead compounds. Wear goggles and gloves when handling batteries and wash
hands after handling.
WARNING! Scooter batteries are heavy. See specifications table. If you are
unable to lift that much weight, be sure to get help. Use proper lifting techniques
and avoid lifting beyond your capacity.
WARNING! Always protect the batteries from freezing and never charge a frozen
battery. Charging a frozen battery may result in damage to the battery.
WARNING! Connect the battery harnesses in the proper manner. RED (+) cables
must be connected to positive (+) battery terminals/posts. BLACK (-) cables must
be connected to negative (-) battery terminals/posts. Protective caps should be
installed over all battery terminals. REPLACE cables immediately if damaged.
BATTERY DISPOSAL AND RECYCLING
If you encounter a damaged or cracked battery, immediately enclose it in a plastic bag. Contact your local
waste disposal agency or your authorised Pride Dealer for instructions on disposal and battery recycling,
which is our recommended course of action.
17
Colt Series www.pridemobility.com
II. SAFETY
PREVENTING UNINTENDED MOVEMENT
WARNING! If you anticipate being seated in a stationary position for an extended period
of time, turn off the power. This will prevent unexpected motion from inadvertent throttle
control lever contact.
MOTOR VEHICLE TRANSPORT
Pride recommends that you do not remain seated in your scooter while traveling in a motor vehicle. The
scooter should be stowed in the boot of a car or in the back of a truck or van with the batteries removed
and/or properly secured. In addition, all removable scooter parts, including the armrests, seat and shroud
should be removed and/or properly secured during motor vehicle transport.
WARNING! Although your scooter may be equipped with a positioning belt, this belt is not
designed to provide proper restraint during motor vehicle transport. Anyone traveling in
a motor vehicle should be properly secured in the motor vehicle seat with safety belts
fastened securely.
WARNING! Do not sit on your scooter while it is in a moving vehicle.
WARNING! Always be sure your scooter and its batteries are properly secured when it is
being transported. Batteries should be secured in an upright position and protective caps
should be installed on the battery terminals. Batteries should not be transported with any
flammable or combustible items.
REACHING AND BENDING
Avoid reaching or bending while driving your scooter. Bending forward creates the risk of accidental
throttle control lever contact. Bending to the side while seated creates the risk of tipping. It is important to
maintain a stable centre of gravity and keep the scooter from tipping. Pride recommends that the scooter
user determine his/her personal limitations and practice bending and reaching in the presence of a qualified
attendant.
WARNING! Do not bend, lean or reach for objects if you have to pick them up from the
scooter deck or from either side of the scooter. Movements such as these may change
your centre of gravity and the weight distribution of the scooter and cause your scooter
to tip.
PROHIBITED! Keep your hands away from the tyres when driving. Be aware that loose
fitting clothing can become caught in drive tyres.
POSITIONING BELTS
Your authorised Pride Dealer, therapist(s) and other healthcare professionals are responsible for determining
your requirement for a positioning belt in order to operate your scooter safely.
WARNING! If you require a positioning belt to safely operate your scooter, make sure it
is fastened securely.
PRESCRIPTION DRUGS/PHYSICAL LIMITATIONS
The scooter user must exercise care and common sense when operating his/her scooter. This includes
awareness of safety issues when taking prescribed or over-the-counter drugs or when the user has specific
physical limitations.
WARNING! Consult your physician if you are taking prescribed or over-the-counter
medication or if you have certain physical limitations. Some medications and limitations
may impair your ability to operate your scooter in a safe manner.
18
www.pridemobility.com Colt Series
II. SAFETY
ALCOHOL/SMOKING
The scooter user must exercise care and common sense when operating his/her scooter. This includes
awareness of safety issues while under the influence of alcohol or while smoking.
WARNING! Do not operate your scooter while you are under the influence of alcohol, as
this may impair your ability to drive safely.
WARNING! Pride strongly recommends that you do not smoke cigarettes while seated on
your scooter, although the scooter has passed the necessary testing requirements for
cigarette smoking. You must adhere to the following safety guidelines if you decide to
smoke cigarettes while seated in your scooter.
Do not leave lit cigarettes unattended.
Keep ashtrays a safe distance from the seat cushions.
Always make sure cigarettes are completely extinguished before disposal.
FLAMMABILITY PRECAUTIONS
WARNING! Even though the plastics used on your scooter have been tested and have
passed the applicable flammability standards, Pride recommends that you do not expose
your scooter to open flames.
WARNING! Replace worn or damaged upholstery immediately to reduce the risk of fire
hazard.
WARNING! Be aware that washing of upholstered items may reduce the resistance to
flammability of the fabric.
ELECTROMAGNETIC AND RADIO FREQUENCY INTERFERENCE (EMI/RFI)
WARNING! Laboratory tests have shown that electromagnetic and radio frequency
waves can have an adverse effect on the performance of electrically-powered mobility
vehicles.
Electromagnetic and Radio Frequency Interference can come from sources such as cellular phones, mobile
two-way radios (such as walkie-talkies), radio stations, TV stations, amateur radio (HAM) transmitters,
wireless computer links, microwave signals, paging transmitters and medium-range mobile transceivers
used by emergency vehicles. In some cases, these waves can cause unintended movement or damage to
the control system. Every electrically-powered mobility vehicle has an immunity (or resistance) to EMI.
The higher the immunity level, the greater the protection against EMI. This product has been tested and
has passed at an immunity level of 20 V/M.
WARNING! Be aware that cell phones, two-way radios, laptops and other types of radio
transmitters may cause unintended movement of your electrically-powered mobility
vehicle due to EMI. Exercise caution when using any of these items while operating your
mobility vehicle and avoid coming into close proximity of radio and TV stations.
WARNING! The addition of accessories or components to the electrically-powered
mobility vehicle can increase the susceptibility of the vehicle to EMI. Do not modify
your scooter in any way not authorised by Pride.
WARNING! The electrically-powered mobility vehicle itself can disturb the performance
of other electrical devices located nearby, such as alarm systems.
NOTE: For further information on EMI/RFI, go to the Resource Centre on www.pridemobility.com. If
unintended motion or brake release occurs, turn the scooter off as soon as it is safe to do so. Contact
your authorised Pride Dealer to report the incident.
19
Colt Series www.pridemobility.com
III. YOUR SCOOTER
TILLER CONSOLE
The tiller console houses all of the controls needed to drive your scooter, including the speed adjustment
dial, key switch, battery condition meter, horn buttons, turn indicator buttons and the throttle control lever.
Please note that some of the features listed in this section are optional items and may not appear on your
scooter. Contact your authorised Pride Dealer for more information. See figure 4.
PROHIBITED! Do not expose the tiller console to moisture. In the event that the tiller
console does become exposed to moisture, do not attempt to operate your scooter until
the tiller console has dried thoroughly.
Figure 4. Tiller Console Components
Speed Adjustment Dial
This dial allows you to preselect and limit your scooter’s top speed.
The image of the tortoise represents the slowest speed setting.
The image of the hare represents the fastest speed setting.
Key Switch
Insert the key into the key switch and turn it clockwise to power up (turn on) your scooter.
Turn the key anticlockwise to power down (turn off) your scooter.
WARNING! If the key is turned to the “off” position while your scooter is in motion, the
electronic brakes will engage and your scooter will come to an abrupt stop!
Battery Condition Meter
When the key is fully inserted and turned clockwise to power up your scooter, this meter indicates the
approximate battery voltage strength. For further information on battery charging, see IV. “Batteries and
Charging.”
SPEED ADJUSTMENT
DIAL
HORN BUTTON
BATTERY CONDITION METER
THROTTLE
CONTROL
LEVER
*LEFT TURN INDICATOR BUTTON
*RIGHT TURN INDICATOR BUTTON
KEY SWITCH
THROTTLE
CONTROL
LEVER
HORN BUTTON
*RIGHT TURN INDICATOR
*LEFT TURN INDICATOR
LIGHTS SWITCH
*HAZARD LIGHTS SWITCH
*OPTIONAL COMPONENTS AVAILABLE ON SOME MODELS
**HI-LOW SWITCH
STATUS LED
*HANDBRAKE LEVER
**AVAILABLE ONLY ON COLT DELUXE AND COLT SPORT MODELS
20
www.pridemobility.com Colt Series
III. YOUR SCOOTER
Horn Buttons
These buttons activate a warning horn. Your scooter must be powered up for the horn to be operational.
Do not hesitate to use the warning horn when doing so may prevent accident or injury.
Turn Indicator Buttons
Use these buttons to turn on the left and right turn indicator (amber) lights.
Push the left button to activate the left turn indicator light. The turn indicator LED located in the battery
condition meter will flash.
Push the right button to activate the right turn indicator light. The turn indicator LED located in the
battery condition meter will flash.
The turn indicators are timed to shut off automatically.
Lights Switch
This switch controls your scooter’s lighting system.
Toggle the switch forward to turn on the front lower light.
Toggle the switch rearward to turn off the lighting system.
WARNING! Scooter users are required to use their lights when visibility is restricted—day
or night.
Hazard Lights Switch
This switch activates the 4-way flashers on your scooter.
Toggle the hazard lights switch forward to turn on the flashers.
Toggle the hazard lights switch rearward to turn off the flashers.
Throttle Control Lever
This lever allows you to control the forward speed and the reverse speed of your scooter up to the
maximum speed you preset with the speed adjustment dial.
To move Forward, use your right thumb to push the right side of the throttle control lever.
To move Rearward, use your left thumb to push the left side of the throttle control lever.
Release the throttle control lever and allow your scooter to come to a complete stop before engaging the
other side of the lever. When the throttle control lever is completely released, it automatically returns to
the centre “stop” position and engages your scooter’s brakes.
Hi-Low Switch
This switch toggles the scooter’s speed between Hi and Low. Toggle the switch forward (Hi) to achieve
the maximum preprogrammed speed for the scooter. Toggle the switch rearward (Low) to achieve half the
maximum preprogrammed speed of the scooter.
Status LED
The status LED alerts you to electrical problems that may occur with the scooter. The LED remains
constantly lit while your scooter is on. If your scooter develops an electrical problem, the status LED will
flash a code. See VIII. “Basic Troubleshooting” for flash codes.
21
Colt Series www.pridemobility.com
Off-board Charger Port
The off-board charger power lead plugs into this port during battery charging. The off-board charger port
is located on the tiller. See figure 5.
Electrical System Fuses
Your scooter is equipped with a series of electrical system fuses, which help protect the off-board
charging system, key switch and lighting system from receiving an overload of electrical current. These
fuses are the same type used in automobiles and are located in a compartment on the tiller. See figure 6.
See IX. “Care and Maintenance” for fuse replacement.
NOTE: Keep all electrical areas clean and free of moisture and foreign material.
III. YOUR SCOOTER
Figure 6. Tiller Console Fuses
KEY SWITCH
OFF-BOARD CHARGER
REAR TAIL LIGHTS
LOWER HEADLIGHT
RIGHT TURN INDICATOR
LEFT TURN INDICATOR
Figure 5. Off-board Charger Port
OFF-BOARD
CHARGER PORT
Figure 7. Rear Components
BATTERY
BATTERY
MANUAL
FREEWHEEL
LEVER
ANTI-TIP WHEELS
REAR COMPONENTS
The batteries, anti-tip wheels, motor/transaxle assembly, main circuit breaker (reset button) and the man-
ual freewheel lever are located on your scooter as shown. See figure 7.
MOTOR/TRANSAXLE ASSEMBLY
22
www.pridemobility.com Colt Series
III. YOUR SCOOTER
Batteries
The batteries store electrical energy that powers your scooter. See IV. “Batteries and Charging ” for
information on how to charge your scooter batteries.
Anti-Tip Wheels
The anti-tip wheels are an integral and important safety feature of your scooter. They are bolted to the
frame at the rear of the scooter.
PROHIBITED! Do not remove the anti-tip wheels or modify your scooter in any way that
is not authorised by Pride.
WARNING! The anti-tip wheels may cause interference with the smooth transition of your
scooter when ascending or descending a kerb. Contact your authorised Pride Dealer for
more information.
Motor/Transaxle Assembly
The motor/transaxle assembly is an electromechanical unit that converts electrical energy from your
scooter’s batteries into the controlled mechanical energy that drives the scooter’s wheels.
Manual Freewheel Lever
Whenever you need or want to push your scooter for short distances, you can put it in freewheel mode.
1. Remove the key from the key switch.
2. Push forward on the manual freewheel lever to disable the drive system and the brake system. This will
enable you to push the scooter.
3. Pull back on the manual freewheel lever to reengage the drive and the brake systems and take your
scooter out of freewheel mode.
WARNING! When your scooter is in freewheel mode, the braking system is disengaged.
Disengage the drive motors only on a level surface.
Ensure the key is removed from the key switch.
Stand to the side of the scooter to engage or disengage freewheel mode. Never sit on
a scooter to do this.
After you have finished pushing your scooter, always return it to the drive mode to
lock the brakes.
NOTE: If the scooter is placed in freewheel mode (manual freewheel lever forward) while the key is in
the “on” position, the scooter will not run until the manual freewheel lever is pushed rearward and the
key is turned to the “off” position, then back to the “on” position.
23
Colt Series www.pridemobility.com
SECURING THE SCOOTER
Always secure the scooter in a forward-facing position in the vehicle. Attach the four tie-down straps to
the designated securement points. See figures 9, 9A and 9B. Tighten the straps to sufficiently remove all
slack. Never attach tie-downs to adjustable, moving or removable parts of the scooter such as armrests,
shrouds and wheels. These items should be removed. Position the anchor points for the rear tie-down
straps directly behind the rear securement points on the scooter. The front tie-down straps should anchor
to floor points that are spaced wider than the scooter to provide increased lateral stability.
WARNING! Ensure scooters are properly secured to the motor vehicle during transport.
Scooters that are not properly secured can become a hazard to the user and to other
vehicle passengers in the event of a crash, sudden stopping, or swerving, as the scooter
could tip or slide out of place.
III. YOUR SCOOTER
Figure 8. Main Circuit Breaker (Reset Button)
MAIN CIRCUIT BREAKER
(RESET BUTTON)
Main Circuit Breaker (Reset Button)
When the voltage in the batteries becomes low or
your scooter is heavily strained because of
excessive loads, the main circuit breaker may trip
to protect the motor and electronics from damage.
When the breaker trips, the entire electrical system
shuts down. See figure 8.
The reset button pops out when the breaker
trips.
Allow a minute or so for the electronics to
“rest.”
Push in the reset button to reset the breaker.
If the breaker trips frequently, you may need to
charge the batteries more often or have your
authorised Pride Dealer perform a load test on
the batteries.
If the main circuit breaker trips repeatedly, see
your authorised Pride Dealer for service.
Figure 9. Front Securement Points
(Colt Twin)
Figure 9A. Front Securement Points
(4-wheel)
Figure 9B. Rear Securement Points
SECUREMENT POINTS
SECUREMENT POINTS
SECUREMENT POINTS
24
www.pridemobility.com Colt Series
IV. BATTERIES AND CHARGING
BATTERIES AND CHARGING
Your scooter requires two long-lasting, 12-volt, deep-cycle batteries that are sealed and maintenance free.
They are recharged by an off-board charging system.
Charge your scooter’s batteries prior to using it for the first time.
Keep the batteries fully charged to keep your scooter running smoothly.
Figure 10. Battery Condition Meter
READING YOUR BATTERY VOLTAGE
The battery condition meter on the tiller console indicates the
approximate strength of your batteries using a colour code. From right
to left, green indicates fully charged batteries, yellow indicates a
draining charge and red indicates that an immediate recharge is
necessary. See figure 10. To ensure the highest accuracy, the battery
condition meter should be checked while operating your scooter at full
speed on a dry, level surface.
CHARGING YOUR BATTERIES
PROHIBITED! Removal of grounding prong can create
electrical hazard. If necessary, properly install an
approved 3-pronged adapter to an electrical outlet
having 2-pronged plug access.
PROHIBITED! Never use an extension lead to plug in your battery charger. Plug the
charger directly into a properly wired standard electrical outlet.
PROHIBITED! Do not allow unsupervised children to play near the scooter while the
batteries are charging. Pride recommends that you do not charge the batteries while the
scooter is occupied.
MANDATORY! Read the battery charging instructions in this manual and in the manual
supplied with the battery charger before charging the batteries.
WARNING! Explosive gases may be generated while charging the batteries. Keep the
scooter and battery charger away from sources of ignition such as flames or sparks and
provide adequate ventilation when charging the batteries.
WARNING! You must recharge your scooter’s batteries with the supplied off-board
charger. Do not use an automotive-type battery charger.
WARNING! Inspect the battery charger, wiring and connectors for damage before each
use. Contact your authorised Pride Dealer if damage is found.
WARNING! Do not attempt to open the battery charger case. If the battery charger does
not appear to be working correctly, contact your authorised Pride Dealer.
WARNING! If the battery charger is equipped with cooling slots, then do not attempt to
insert objects through these slots.
WARNING! Be aware that the battery charger case may become hot during charging.
Avoid skin contact and do no place on surfaces that may be affected by heat.
WARNING! If your battery charger has not been tested and approved for outdoor use, then
do not expose it to adverse or extreme weather conditions. If the battery charger is
exposed to adverse or extreme weather conditions, then it must be allowed to adjust to
the difference in environmental conditions before use indoors. Refer to the manual
supplied with the battery charger for more information.
25
Colt Series www.pridemobility.com
IV. BATTERIES AND CHARGING
Follow these easy steps to charge the batteries:
1. Position the front of your scooter close to a
standard electrical outlet.
2. Remove the key from the key switch.
3. Make sure that the manual freewheel lever is in
the drive position.
4. Plug the 3-pin charger power lead into the off-
board charger port. See figures 5 and 11.
5. Extend the charger power lead and plug it into
the electrical outlet. We recommend that you
charge the batteries for 8 to 14 hours.
6. When the batteries are fully charged, unplug the
charger power cord from the electrical outlet and
then from the off-board charger port.
NOTE: The LED lights on the charger indicate different charger conditions at various times: charger
power on, charging in progress and charging complete. Refer to the manual supplied with the charger
for a complete explanation of these indicators.
NOTE: There is a charger inhibit function on your scooter. The scooter will not run and the battery
condition meter will not operate while the batteries are charging.
FREQUENTLY ASKED QUESTIONS
How does the charger work?
When your scooter’s battery voltage is low, the charger works harder, sending more electrical current to
the batteries to bring up their charge. As the batteries approach a full charge, the charger sends less and
less electrical current. When the batteries are fully charged, the current sent from the charger is at nearly
zero amperage. Therefore, when the charger is plugged in, it maintains the charge on your scooter’s
batteries, but does not overcharge them. Refer to the manual supplied with the battery charger for charging
instructions.
Can I use a different charger?
Chargers are selected precisely for particular applications and are especially matched to the type, size
and chemical formulation of specific batteries. For the safest and most efficient charging of your
scooter’s batteries we recommend only use of the charger supplied as original equipment with your
Pride product. Any charging method resulting in batteries being charged individually is especially
prohibited.
What if my scooter’s batteries won’t charge?
Ensure the red (+) and black (-) battery cables are connected properly to the battery terminals.
Ensure both battery harnesses that extend from the batteries are plugged into their mating harness
leading to the charger.
Ensure both ends of the charger power lead are inserted fully.
Figure 11. Off-board Charger
PLUGS INTO THE OFF-BOARD CHARGER PORT
PLUGS INTO ELECTRICAL OUTLET
26
www.pridemobility.com Colt Series
IV. BATTERIES AND CHARGING
How often must I charge the batteries?
Two major factors must be considered when deciding how often to charge your scooter’s batteries:
All day scooter use on a daily basis.
Infrequent or sporadic scooter use.
With these considerations in mind, you can determine how often and for how long you should charge your
scooter’s batteries. The off-board charger was designed so that it will not overcharge your scooter’s
batteries. However, you may encounter some problems if you do not charge your batteries often enough
and if you do not charge them on a regular basis.
Following the guidelines below will provide safe and reliable battery operation and charging.
If you use your scooter daily, charge its batteries as soon as you finish using it for the day. Your scooter
will be ready each morning. We recommend that you charge your scooter’s batteries for 8 to 14 hours
after daily use.
If you use your scooter once a week or less, charge its batteries at least once a week for 12 to 14 hours
at a time.
Keep your scooter’s batteries fully charged.
Avoid deeply discharging your scooter’s batteries.
How can I ensure maximum battery life?
Fully charged deep-cycle batteries provide reliable performance and extended battery life. Keep your
scooter’s batteries fully charged whenever possible. Protect your scooter and batteries from extreme heat
or cold. Batteries that are regularly and deeply discharged, infrequently charged, stored in extreme
temperatures or stored without a full charge may be permanently damaged, causing unreliable
performance and limited service life.
How can I get maximum range or distance per charge?
Rarely will you have ideal driving conditions—smooth, flat, hard driving surfaces with no wind or curves.
Often, you will face hills, pavement cracks, uneven and loosely packed surfaces, curves and wind, all of
which affect the distance or running time per battery charge. Below are a few suggestions for obtaining
the maximum range per battery charge.
Always fully charge your scooter’s batteries prior to daily use.
Maintain but do not exceed the psi/bar/kPa air pressure rating indicated on each tyre.
Plan your route ahead to avoid as many hills, cracked, broken or soft surfaces as possible.
Limit your baggage weight to essential items.
Try to maintain an even speed while your scooter is in motion.
Avoid stop-and-go driving.
What type and size of battery should I use?
We recommend deep-cycle batteries that are sealed and maintenance free. Both AGM and Gel-Cell are deep-
cycle batteries that are similar in performance. Do not use wet-cell batteries, which have removable caps.
WARNING! Corrosive chemicals are contained in batteries. Use only AGM or Gel-
Cell batteries to reduce the risk of leakage or explosive conditions.
NOTE: Sealed batteries are not serviceable. Do not remove the caps.
27
Colt Series www.pridemobility.com
To change the batteries in your scooter:
WARNING! Do not lift beyond your
physical capability. Ask for assistance
when necessary while disassembling or
assembling your scooter.
1. Remove the seat and battery shroud.
2. Disconnect the battery tie-down strap.
3. Disconnect the battery harnesses by depressing the
tabs and then pulling them straight up. See figure 12.
4. Disconnect the battery cables from the battery
terminals by sliding back the terminal boots and
unscrewing the nut from the bolt. See figure 12.
5. Remove the old batteries from the battery wells.
6. Place a new battery in each battery well. Face the
battery terminals of each battery away from the seat
post. See figure 13.
7. Connect the red battery cable to the positive (+)
battery terminal on each battery.
8. Connect the black battery cable to the negative (-)
battery terminal on each battery.
9. Reposition the terminal boots over the battery
terminals.
10. Reconnect the battery harnesses.
11. Reconnect the battery tie-down strap.
12. Reinstall the battery shroud and seat.
How do I change a battery in my scooter?
MANDATORY! Battery posts, terminals and related accessories contain lead and
lead compounds. Wear goggles and gloves when handling batteries and wash
hands after handling.
WARNING! Always use two batteries of the exact same type, chemistry and amp-
hour (Ah) capacity. Refer to the specifications table with this manual and in the
manual supplied with the battery charger for recommended type and capacities.
WARNING! Do not mix old and new batteries. Always replace both batteries at the
same time.
WARNING! Contact your authorised Pride Dealer if you have any questions
regarding the batteries in your scooter.
WARNING! Do not replace the batteries while the scooter is occupied.
WARNING! The batteries on your scooter should only be serviced or replaced by
an authorised Pride Dealer or a qualified technician.
PROHIBITED! Keep tools and other metal objects away from battery terminals.
Contact with tools can cause electrical shock.
IV. BATTERIES AND CHARGING
Figure 13. Battery Wiring Diagram
Figure 12. Battery Removal/Installation
BATTERY TERMINALS UNDER BOOTS
BATTERY HARNESS CONNECTIONS
You may need the following to change your batteries:
Metric/standard socket set and ratchet
Adjustable spanner
BATTERY
CONNECTION
UNDER BOOT
28
www.pridemobility.com Colt Series
IV. BATTERIES AND CHARGING
NOTE: If you encounter a damaged or cracked battery, immediately enclose it in a plastic bag. Contact
your local waste disposal agency or your authorised Pride Dealer for instructions on disposal and
battery recycling, which is our recommended course of action.
Why do my new batteries seem weak?
Deep-cycle batteries employ a different chemical technology than that used in car batteries, nickel-
cadmium batteries (nicads) and other common battery types. Deep-cycle batteries are specifically
designed to provide power, drain down their charge and then accept a relatively quick recharge.
We work closely with our battery manufacturer to provide batteries that best suit your scooter’s specific
electrical demands. Fresh batteries are shipped fully charged to our customers. During shipping, the
batteries may encounter temperature extremes that can influence their initial performance. Heat diminishes
the charge on the battery; cold slows the available power and extends the time needed to recharge the
battery.
It may take a few days for the temperature of your scooter’s batteries to stabilise and adjust to their new
room or ambient temperature. More importantly, it takes a few charging cycles (partial draining followed
by full recharging) to establish the critical chemical balance that is essential to a deep-cycle battery’s peak
performance and long life.
Follow these steps to properly break in your scooter’s new batteries for maximum efficiency and
service life:
1. Fully recharge any new battery prior to its initial use. This charging cycle brings the battery up to about
88% of its peak performance level.
2. Operate your new scooter in familiar and safe areas. Drive slowly at first and do not travel too far from
your home or familiar surroundings until you have become accustomed to your scooter’s controls and
have properly broken in your scooter’s batteries.
3. Fully recharge the batteries. They should be at over 90% of their peak performance level.
4. Operate your scooter again.
5. Fully recharge the batteries again.
6. After four or five charging cycles, the batteries are able to receive a charge of 100% of their peak
performance level and are able to last for an extended period of time.
What about public transport?
If you intend to use public transportation with your scooter, you must contact the transportation provider
in advance to determine their specific requirements.
29
Colt Series www.pridemobility.com
V. OPERATION
BEFORE GETTING ONTO YOUR SCOOTER
Have you fully charged the batteries? See IV. “Batteries and Charging.”
Is the manual freewheel lever in the drive (rearward) position? Never leave the manual freewheel lever
pushed forward unless you are manually pushing your scooter.
GETTING ONTO YOUR SCOOTER
1. Make certain that the key is removed from the key switch.
WARNING! Never attempt to get onto or off of your scooter without first removing the key
from the key switch. This will prevent the scooter from moving if accidental throttle
control lever contact is made.
2. Stand at the side of your scooter.
3. Disengage the seat rotation lever and rotate the seat until it is facing you.
4. Make certain that the seat is fixed securely in position.
5. Position yourself comfortably and securely in the seat.
6. Disengage the seat rotation lever and rotate the seat until you are facing forward.
7. Make certain that the seat is fixed securely in position.
8. Make certain that your feet are safely on the floorboard.
PRE-RIDE ADJUSTMENTS AND CHECKS
Is the seat at the proper height? See VI. “Comfort Adjustments.”
Is the seat fixed securely in position?
Is the tiller at a comfortable setting and locked securely in place? See VI. “Comfort Adjustments.”
Is the key fully inserted into the key switch and turned clockwise to the “on” position?
Does the horn work properly?
Is your proposed path clear of people, pets and obstacles?
Have you planned your route to avoid adverse terrain and as many inclines as possible?
OPERATING YOUR SCOOTER
WARNING! The following can adversely affect steering and stability while operating your
scooter, resulting in loss of control, tipping and/or personal injury:
Holding onto or attaching a leash to walk your pet
Carrying passengers (including pets)
Hanging any article from the tiller
Towing or being pushed by another motorised vehicle
WARNING! Keep both hands on the tiller and your feet on the floorboard at all times while
operating your scooter. This driving position gives you the most control over your vehicle.
Set the speed adjustment dial to your desired speed.
Push or pull the appropriate side of the throttle control lever.
The electromechanical disc park brake automatically disengages and the scooter accelerates smoothly
to the speed you preselected with the speed adjustment dial.
Pull on the left handgrip to steer your scooter to the left.
Pull on the right handgrip to steer your scooter to the right.
Move the tiller to the centre position to drive straight ahead.
To stop, slowly release the throttle control lever. The electronic brakes will automatically engage,
bringing your scooter to a stop.
30
www.pridemobility.com Colt Series
V. OPERATION
NOTE: Your scooter’s reverse speed is slower than that of the forward speed you preset with the speed
adjustment dial.
GETTING OFF OF YOUR SCOOTER
1. Bring your scooter to a complete stop.
2. Power down your scooter and remove the key from the key switch.
3. Disengage the seat rotation lever and rotate the seat until you are facing toward the side of your scooter.
4. Make certain that the seat is fixed securely in position.
5. Carefully and safely get out of the seat and stand to the side of your scooter.
6. You can leave the seat facing to the side to facilitate boarding your scooter next time.
POWER DOWN TIMER FEATURE
Your scooter is equipped with an energy saving automatic power down timer feature designed to preserve
your scooter’s battery life. If you mistakenly leave the key in the key switch and in the “on” position but
do not use your scooter for approximately 20 minutes, the scooter’s controller shuts down automatically.
Although the controller is shut down, power will still be supplied to the scooter’s lighting system.
If the power down timer feature takes effect, perform the following steps to resume normal operation:
1. Turn the key to the “off” position.
2. Turn the key to the “on” position.
31
Colt Series www.pridemobility.com
TILLER ANGLE ADJUSTMENT
WARNING! Remove the key from the
key switch before adjusting the tiller
or the seat. Never attempt to adjust
the tiller or the seat while the
scooter is in motion.
Your scooter is equipped with an adjustable pivoting
tiller.
1. While supporting the tiller, turn the tiller
adjustment knob anticlockwise to loosen the
tiller. See figure 14.
2. Move the tiller to a comfortable position.
3. Turn the tiller adjustment knob clockwise to
secure the tiller in position.
NOTE: In order to fully lower the tiller for purposes
of disassembly or transport, you must first
completely remove the seat. See VII. “Disassembly
and Assembly.”
MIRROR POSITION
To install the mirror (see figure 15):
1. Determine on which side to install the mirror and
remove the rubber plug from the top of the tiller
handle.
2. Insert the threaded end of the mirror holder into
the opening and rotate it clockwise until snug.
3. If necessary, rotate the nut clockwise to secure
the mirror in place.
To adjust the mirror:
1. Position yourself in a seated driving position
facing forward.
2. Adjust the mirror left, right, up or down until you
have a good line of sight behind you.
ARMREST WIDTH ADJUSTMENT
The armrest width can be adjusted inward or outward.
1. Loosen the armrest adjustment knobs. See
figure 16.
2. Use the attached ring to pull and remove the
detent pins.
3. Slide the armrests in or out to the desired width.
4. Align the adjustment holes on the seat frame and
armrest, then reinsert the detent pin.
5. Tighten the armrest adjustment knobs.
NOTE: Pivot the armrests upward to aid in getting
onto and off of your scooter.
VI. COMFORT ADJUSTMENTS
TILLER
ADJUSTMENT
KNOB
Figure 14. Tiller Adjustment
Figure 15. Mirror Installation and Positioning
Figure 16. Armrest Width Adjustment
MIRROR HOLDER
RUBBER PLUG
NUT
ARMREST ADJUSTMENT KNOBS
DETENT PINS
32
www.pridemobility.com Colt Series
VI. COMFORT ADJUSTMENTS
Figure 17. Seat Position Adjustments
SEAT ROTATION ADJUSTMENT
The seat rotation lever will secure the seat into
several positions.
1. Pull upward on the seat rotation lever to
disengage the seat. See figure 17 or 19.
2. Rotate the seat to the desired position.
3. Release the lever to secure the seat into place.
SEATBACK ADJUSTMENT
WARNING! Do not operate your
scooter with the seatback in a
reclined position.
WARNING! Always keep your back
pressed firmly against the seatback
while adjusting the angle.
If you scooter is equipped with a reclining seatback,
you can adjust the seatback angle with the seatback
adjustment lever. See figure 18.
1. With your back pressed up against the seatback,
lift up on the seatback adjustment lever and lean
forward or rearward to adjust the seatback angle.
2. Release the seatback adjustment lever once the
seat is in a comfortable riding position.
FRONT-TO-BACK SEAT ADJUSTMENT
If your scooter is equipped with an adjustable seat,
you can reposition the seat forward or rearward to
adjust the distance between the seat and the tiller.
1. Move the seat sliding lever located at the lower
left side of the seat outward. See figure 19.
2. While holding the lever out, slide the seat
forward or rearward.
3. Release the seat sliding lever once the seat is in
the desired position.
ARMREST ANGLE ADJUSTMENT
Armrest angle of your scooter can be adjusted
upwards or downwards by turning the adjustment
knob. See figure 19.
NOTE: The armrests also pivot upward to make
getting on and off of your scooter easier
SEAT ROTATION LEVER
Figure 18. Seatback Adjustment
SEATBACK
ADJUSTMENT
LEVER
Figure 19. CRS Junior Seat Position Adjustments
ADJUSTMENT DIAL
SEAT SLIDING LEVER
SEAT ROTATION LEVER
33
Colt Series www.pridemobility.com
SEAT HEIGHT ADJUSTMENT
The seat can be repositioned to several different
heights. See figure 20.
1. Remove the seat and/or shroud from your
scooter. See VII. “Disassembly and Assembly.”
2. Remove the seat height adjustment bolt.
3. Raise or lower the upper seat post to the
desired seat height.
4. While holding the upper seat post at that
height, match up the locating holes in the upper
seat post with those of the lower seat post.
5. Insert the seat height adjustment bolt through
the locating holes of both the upper and lower
seat posts.
6. Reinstall the nut onto the seat height
adjustment bolt and tighten.
7. Reinstall the shroud and the seat.
SEAT HEIGHT ADJUSTMENT—COMFORT
SEAT POST (IF EQUIPPED)
To reposition the seat to one of two different
heights:
1. Remove the seat from your scooter. Push forward
and hold the seat rotation lever to disengage the
seat, then rotate the seat and lift it off of the
scooter.
2. Remove the rear shroud.
3. Push up the seat post boot to uncover the
hardware.
4. Push down on the seat post while loosening and
removing the shoulder bolt, washer, and nut. See
figure 21.
5. Remove the comfort spring.
6. To raise the seat to the top most mounting hole,
insert the height adjustment spacer. To lower the
seat to the lowest mounting hole, remove the
height adjustment spacer.
7. Reinstall the comfort spring.
8. Hold the upper seat post at the desired height and
match up the locating holes in the lower seat post.
Utilize the top holes for the upper position or the
bottom holes for the lower position.
9. Press down on the seat post while reinstalling the
hardware and tightening to 210 in • lb (24 N • m).
10. Replace the rear shroud and the seat.
Figure 20. Seat Height Adjustment
LOWER
SEAT
POST
SEAT HEIGHT
ADJUSTMENT
BOLT
NUT
LOCATING
HOLE
UPPER SEAT
POST
VI. COMFORT ADJUSTMENTS
34
www.pridemobility.com Colt Series
VI. COMFORT ADJUSTMENTS
SEAT SUSPENSION ADJUSTMENT (AVAILABLE ONLY ON COLT DELUXE MODEL)
You can loosen or stiffen the seat suspension based on which comfort spring you install.
To adjust the seat suspension:
1. Remove the seat from your scooter. Push down and hold the seat rotation lever to disengage the seat,
then rotate the seat and lift it off of the scooter.
2. Remove the rear shroud.
3. Push up the seat post boot to uncover the hardware.
4. Push down on the seat post while loosening and removing the hex head bolt and nut.
5. Remove the current spring.
6. Install the desired spring. See figure 21.
7. Press down on the seat post while reinstalling the hardware and tightening to 210 in • lb (24 N • m).
8. Replace the rear shroud and the seat.
SPRING WEIGHT CAPACITY
0-90.72 kg (0 - 220 lbs.)
BOOT
NUT
WASHER
UPPER SEAT POST
OPTIONAL SPRING WEIGHT
CAPACITY WITH HEIGHT
ADJUSTMENT SPACER
90.72 - 181.44 kg (220-400 lbs.)
SHOULDER BOLT
(210 IN • LB [24 N • M])
SPACER
LOWER SEAT POST
Figure 21. Seat Height Adjustment - Comfort Seat Post
35
Colt Series www.pridemobility.com
VI. COMFORT ADJUSTMENTS
POSITIONING BELT (OPTIONAL)
Your scooter seat may be equipped with an auto-
type positioning belt that can be adjusted for
operator comfort. The positioning belt is designed
to help support the operator so that he or she does
not slide down or forward in the seat. The
positioning belt is not designed for use as a
restraining device.
To install the positioning belt (if required):
1. Remove the seat from your scooter.
2. Place the seat upside down so that you can see
the bottom of the seat base. See figure 22 or
22A.
3. Use a wrench to remove the two back bolts on
the outermost part of the rear seat.
4. Insert the bolt through the appropriate ends of
the positioning belt and then reinstall the bolts
and belt back into the seat bottom.
5. Tighten the bolts.
To adjust the positioning belt for operator
comfort:
1. Insert the metal tab on the right side of the belt
into the plastic housing on the opposite strap
until you hear a “click.” See figure 23.
2. Pull the strap on the right side of the belt until
it is secure, but not so tight as to cause discom-
fort.
To release the positioning belt:
1. Press the push button mechanism on the plastic
housing.
MANDATORY! Make sure the posi-
tioning belt is properly secured to
the scooter and is adjusted for
operator comfort before each use.
MANDATORY! Inspect the posi-
tioning belt for loose or damaged
parts before each use of the
scooter. If you discover a problem,
contact your authorised Pride
Dealer for maintenance and repair.
Figure 23. Positioning Belt
Figure 22. Positioning Belt Bolts (CRS Junior seat)
POSITIONING
BELT BOLTS
POSITIONING
BELT BOLTS
Figure 22A. Positioning Belt Bolts
36
www.pridemobility.com Colt Series
DISASSEMBLY
You can disassemble the scooter into several
pieces: the seat, the front section, the rear section,
the battery shroud, the basket and the batteries.
See figure 24 or 24A. No tools are required to
disassemble or assemble your scooter, but keep
in mind that the disassembled sections of the
scooter take up more floor space than the
assembled unit. Always disassemble or assemble
your scooter on a level, dry surface with
sufficient room for you to work and move around
your
scooter—about
1.5 metres (5 feet) in all
directions. Remember that some scooter
components are heavy and you may need
assistance when lifting them.
WARNING! Do not lift beyond
your physical capability. Ask for
assistance when necessary
while disassembling or
assembling your scooter.
1. Remove the seat by lifting it straight up and
off of the scooter. If you encounter resistance
when removing the seat, disengage the seat
rotation lever and swivel the seat back and
forth while lifting up on the seat.
2. Gently pull the battery shroud forward, then
lift up and off of the scooter. See figure 25.
3. Disconnect the battery tie-down strap.
4. Unplug both battery harnesses by depressing
the tabs and then pulling each harness straight
up. See figure 26.
5. Remove the batteries from the battery wells.
WARNING! Failure to unplug both
battery harnesses prior to
separating the front and rear
sections could result in
permanent damage to the
scooter.
Frame Separation
1. Arrange the front wheel(s) in a straight
forward-facing position.
2. Lower the tiller and tighten the tiller
adjustment knob.
VII. DISASSEMBLY AND ASSEMBLY
Figure 24. Scooter Components
FRONT SECTION
SEAT
REAR SECTION
BATTERY SHROUD
BATTERIES
BASKET
Figure 24A. Scooter Components (Colt Twin model only)
REAR SECTION
SEAT
FRONT SECTION
BASKET
BATTERIES
BATTERY SHROUD
Figure 25. Battery Shroud Removal
37
Colt Series www.pridemobility.com
VII. DISASSEMBLY AND ASSEMBLY
Figure 27. Frame Release Lever
FRAME
RELEASE
LEVER
NOTE: The pivoting tiller is equipped with a
mechanism that will lock the front wheels in
place when the tiller is completely lowered and
secured.
3. Grasp and lift up on the frame release lever.
See figure 27.
4. Lift the front section up until the frame hooks
of the front section separate from the rear
section. See figure 28 or 28A.
5. Slowly separate the two sections. See figure 28
or 28A.
ASSEMBLY
1. Position the front and rear sections of your
scooter as shown in see figure 28 or 28A.
2. Use the frame release lever to lift the front
section as you align the frame hooks of the
front section with the lower frame tube of the
rear section. See figure 28 or 28A.
3. Once the frame hooks are over the lower
frame tube, lower the front section
completely. This will engage the frame lock.
4. Raise the tiller and fully tighten the tiller
adjustment knob.
5. Reinstall the batteries to the battery wells.
6. Connect both battery harnesses. See figure 26.
7. Secure the battery tie-down strap.
8. Reinstall the battery shroud.
9. Reinstall the seat and rotate it into place.
WARNING! After assembly, make
absolutely certain the tiller lock
knob is in the unlocked position
before driving the scooter.
LOWER FRAME TUBE
FRAME HOOKS
Figure 28A. Frame Separation (Colt Twin model only)
Figure 28. Frame Separation
FRAME HOOKS
LOWER FRAME TUBE
Figure 26. Harness Connections
BATTERY HARNESS CONNECTIONS
38
www.pridemobility.com Colt Series
VIII. BASIC TROUBLESHOOTING
Any electromechanical device occasionally requires some troubleshooting. However, most of the
problems that may arise can usually be solved with a bit of thought and common sense. Many of these
problems occur because the batteries are not fully charged or because the batteries are worn down and can
no longer hold a charge.
DIAGNOSTIC FAULT CODES
The diagnostic fault codes for your scooter are designed to help you perform basic troubleshooting quickly
and easily. A flash or audible diagnostic code will come from the scooter (depending on model) in the
event one of the conditions listed below develops.
NOTE: Your scooter will not run unless the fault code condition is resolved and the scooter has been
turned off, then turned back on.
What if all the systems on my scooter seem to be dead?
Make certain that the key is in the “on” position.
Check that the batteries are fully charged.
Push in the main circuit breaker reset button. See III. “Your Scooter.”
Make certain that both battery harnesses are firmly connected. See VII. “Disassembly and Assembly.”
Be sure the power down timer feature has not been activated. See V. “Operation.”
FAULT CODE CONDITION SOLUTION
(1)
Battery charge is low. Charge batteries as soon as possible.
  (2)
Battery charge is too low. Charge batteries.
   (3)
The scooter's battery voltage is too
high to operate the scooter, or the
charger is still connected to the off-
board charger port.
Unplug charger and/or turn key off,
then back on again.
    (4)
Current limit time out. Turn the scooter off for a few
minutes, then turn your scooter
back on.
     (5)
The manual freewheel lever is in the
(forward) freewheel position.
Remove the key from the key
switch, then push the manual free-
wheel lever to the drive (rearward)
position and restart your scooter.
     (6)
Throttle control lever not at centre
position at start up.
Return the throttle control lever to
centre position, turn scooter off then
back on.
       (7)
Speed pot error. Call your authorised Pride Dealer
for assistance.
        (8)
Motor volts error. Call your authorised Pride Dealer
for assistance.
     
(9)
Other internal errors. Call your authorised Pride Dealer
for assistance.
39
Colt Series www.pridemobility.com
VIII. BASIC TROUBLESHOOTING
What if my scooter does not move when I engage the throttle control lever?
When the manual freewheel lever is pushed forward, the brakes are disengaged and all power to the
motor/transaxle assembly is cut.
Push rearward on the manual freewheel lever, turn the scooter off and then turn the scooter on to return
to normal scooter operation.
What if the main circuit breaker repeatedly trips?
If the main circuit breaker trips repeatedly, see your authorised Pride Dealer for service.
Charge the batteries more frequently. See IV. “Batteries and Charging.”
If the problem continues, have both of your scooter’s batteries load tested by your authorised
Pride Dealer.
You may also perform the load test yourself. Battery load testers are available at most automotive parts
stores. Follow the directions supplied with the load tester.
See IV. “Batteries and Charging” or “Product Specifications” insert for information about your
scooter’s battery type.
What if the battery condition meter dips way down and the motor surges or hesitates when I engage
the throttle control lever?
Fully charge your scooter’s batteries. See IV. “Batteries and Charging.”
Have your authorised Pride Dealer load test each battery.
See the previous troubleshooting question for load testing the batteries yourself.
If you experience any problems with your scooter that you are not able to solve, immediately contact your
authorised Pride Dealer for information, maintenance and service.
40
www.pridemobility.com Colt Series
Follow these easy steps for a quick and safe repair
for solid tyres:
1. Remove the key from the key switch.
2. Elevate the side of the scooter of which you are
removing the tyre. Place wooden blocks under the
frame to elevate the scooter.
3. Remove the wheel cap, drive wheel nut and
washer from the axle. See figure 29.
4. Pull the wheel off of the axle.
5. Slide the new wheel onto the axle. Make sure the
the axle key is in the axle slot.
WARNING! Failure to ensure that the
axle key is properly installed into the
axle slot when mounting the wheel can
result in electronic brake failure,
personal injury and/or product damage.
6. Reinstall the drive wheel nut and washer onto the axle and tighten.
WARNING! Make sure that both the nut and washer are reinstalled and tightened
properly.
7. Reinstall the wheel cap.
8. Remove the blocks from beneath the scooter.
IX. CARE AND MAINTENANCE
Your scooter requires a minimal amount of care and maintenance. If you do not feel confident in your
ability to perform the maintenance listed below, you may schedule inspection and maintenance at your
authorised Pride Dealer. The following areas require periodic inspection and/or care and maintenance.
TYRE PRESSURE
If equipped with pneumatic tyres, always maintain the psi/bar/kPa air pressure rating indicated on
each tyre.
WARNING! It is important that the psi/bar/kPa air pressure rating indicated on each tyre
be maintained in pneumatic tyres at all times. Do not underinflate or overinflate your
tyres. Low pressure may result in loss of control and overinflated tyres may burst. Failure
to maintain the psi/bar/kPa air pressure rating indicated on the tyres at all times may
result in tyre and/or wheel failure.
Regularly inspect your scooter’s tyres for signs of wear.
WHEEL REPLACEMENT
If your scooter is equipped with pneumatic tyres and you have a flat tyre, you can have the tube replaced. If your
scooter is equipped with a solid tyre insert, either the solid insert or the entire wheel must be replaced depending
on the model. Contact your authorised Pride Dealer for information regarding replacement wheels for your scooter.
WARNING! Be sure that the key is removed from the key switch and the scooter is not in
freewheel mode before performing this procedure repair.
WARNING! Completely deflate pneumatic tyres before dismantling the wheel or attempting
repair.
WARNING! When changing a tyre, remove only the centre lug nut, then remove the wheel. If
any further disassembly is required, deflate the tyre completely or it may explode.
WARNING! Wheels on your scooter should only be serviced/replaced by an authorised Pride
Dealer or qualified technician.
Figure 29. Solid Tyre Wheel Removal
AXLE
KEY
WASHER
DRIVE WHEEL NUT
WHEEL CAP
AXLE SLOT
41
Colt Series www.pridemobility.com
IX. CARE AND MAINTENANCE
EXTERIOR SURFACES
Bumpers, tyres and trim can benefit from an occasional application of a rubber or vinyl conditioner.
WARNING! Do not use a rubber or vinyl conditioner on the scooter’s vinyl seat or tyre
tread, as this may cause them to become dangerously slippery.
CLEANING AND DISINFECTION
Use a damp cloth and mild, non-abrasive cleanser to clean the plastic and metal parts of your scooter.
Avoid using products that may scratch the surface of your scooter.
If necessary, clean your product with an approved disinfectant. Make sure the disinfectant is safe for
use on your product before application.
WARNING! Follow all safety instructions for the proper use of the disinfectant and/or
cleaning agent before applying it to your product. Failure to comply may result in skin
irritation or premature deterioration of upholstery and/or scooter finishes.
BATTERY TERMINAL CONNECTIONS
Make certain that the terminal connections remain tight and uncorroded.
The batteries must sit flat in the battery wells.
The battery terminals should face towards the outside of the scooter.
WIRING HARNESSES
Regularly check all wiring connections.
Regularly check all wiring insulation, including the charger power lead, for wear or damage.
Have your authorised Pride repair or replace any damaged connector, connection or insulation that you
find before using your scooter again.
PROHIBITED! Even though the scooter has passed the necessary testing requirements
for ingress of liquids, you should keep electrical connections away from sources of
dampness, including direct exposure to water or bodily fluids and incontinence. Check
electrical components frequently for signs of corrosion and replace as necessary.
WARNING! Do not pull on electrical harnesses directly to detach them from the scooter.
Always grasp the connector itself when disconnecting the harness to prevent wire
damage.
ABS PLASTIC SHROUDS
The front tiller shroud, front shroud and the rear shroud are formed from durable ABS plastic and are
coated with an advanced formula urethane paint.
A light application of car wax will help the shrouds retain their high gloss.
AXLE BEARINGS AND THE MOTOR/TRANSAXLE ASSEMBLY
These items are all prelubricated, sealed and require no subsequent lubrication.
MOTOR BRUSHES
The motor brushes are housed inside of the motor transaxle/assembly. They should be inspected
periodically for wear by your authorised Pride Dealer.
CONSOLE, CHARGER AND REAR ELECTRONICS
Keep these areas free of moisture.
Allow these areas to dry thoroughly if they have been exposed to moisture before operating your
scooter again.
42
www.pridemobility.com Colt Series
IX. CARE AND MAINTENANCE
FUSE REPLACEMENT
In the event a fuse should cease to work:
1. Remove the fuse by pulling it out of its slot.
2. Examine the fuse to be sure it is blown. See figures 30 and 30A.
3. Insert a new fuse of the same rating.
WARNING! The replacement fuse must exactly match the rating of the fuse being
replaced. Failure to use properly rated fuses may cause damage to the electrical system.
NYLON LOCK NUT REPLACEMENT
Any nylon insert lock nut removed during the periodic maintenance, assembly or disassembly of the
scooter must be replaced with a new nut. Nylon insert lock nuts should not be reused as it may cause
damage to the nylon insert, resulting in a less secure fit. Replacement nylon insert lock nuts are available
at local hardware stores or through your authorised Pride Dealer.
STORING YOUR SCOOTER
If you plan on not using your scooter for an extended period of time, it is best to:
1. Fully charge its batteries prior to storage.
2. Disconnect the batteries from the scooter.
3. Store your scooter in a warm, dry environment.
4. Avoid storing your scooter where it will be exposed to temperature extremes.
WARNING! Always protect batteries from freezing temperatures and never charge a
frozen battery. Charging a frozen battery can result in damage to the battery.
Batteries that are regularly and deeply discharged, infrequently charged, stored in extreme temperatures
or stored without a full charge may be permanently damaged, causing unreliable performance and limited
service life. It is recommended that you charge the scooter batteries periodically throughout periods of
prolonged storage to ensure proper performance.
You may wish to place several boards under the frame of your scooter to raise it off of the ground during
periods of prolonged storage. This takes the weight off the tyres and reduces the possibility of flat spots
developing on the areas of the tyres contacting the ground.
DISPOSAL OF YOUR SCOOTER
Your scooter must be disposed of according to applicable local and national statutory regulations. Contact
your local waste disposal agency or authorised Pride Dealer for information on proper disposal of
packaging, metal frame components, plastic components, electronics, batteries, neoprene, silicone and
polyurethane materials.
Figure 30. Working Fuse Figure 30A. Blown Fuse (Replace)
43
Colt Series www.pridemobility.com
X. WARRANTY
LIFETIME WARRANTY
Structural frame components, including: platform, fork, seat post and frame welds.
TWO-YEAR LIMITED WARRANTY
Drivetrain, including: transaxle, motor and brake.
ONE-YEAR LIMITED WARRANTY
All electrical parts, including controllers and battery chargers, are covered for one year under warranty.
Any attempt to open or dismantle these parts will lead to this warranty being void.
BATTERIES
Batteries are covered by a twelve-month warranty from the original manufacturer.
NOT COVERED UNDER WARRANTY
The following are classed as wear items, which may, under normal wear and tear, require replacing. These
items are not therefore covered under warranty: tyres, lap belts, bulbs, upholstery, plastic shrouds, motor
brushes and fuses. Warranty will also be refused if damage is deemed to have been caused through misuse
or accident for which Pride Mobility Products Ltd. cannot be deemed responsible.
NOTE: Pride Mobility Products Ltd. provides parts only under warranty. Your authorised Pride Dealer
is responsible for labour and service. Please contact your authorised Pride Dealer for information about
these services and for any applicable charges.
… 43 …

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Pride Colt Series bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Pride Colt Series in de taal/talen: Engels als bijlage per email.

De handleiding is 3,41 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info