554006
55
Verklein
Vergroot
Pagina terug
1/56
Pagina verder
Commercial Treadmill Owner’s Manual
COMMERCIAL PRODUCTS DIVISION
C954
C956
page 2
COMMERCIAL PRODUCTS DIVISION
When using the C956 or C954 treadmill, always follow basic precautions, including the following:
To ensure your safety and to protect the unit, read all the instructions before assem-
bling and using the treadmill.
To ensure the proper use and safety of the treadmill, make sure that all users read
this manual. Please make this manual a part of your club’s training program.
Remind the club users that before beginning any fitness program, they should
obtain complete physical examinations from their physicians.
Il est conseillé de subir un examen médical complet avant d’entre-prendre tout
programme d’exercise. Si vous avez des étourdissements ou des faiblesses, arrêtez
les exercices immédiatement.
DANGER —
WARNING —
Do not allow children or those unfamiliar with its operation on or near the treadmill.
Do not leave children unsupervised around the treadmill.
Never leave the treadmill unattended. Unplug the unit from the power outlet when it
is not in use, before cleaning it, and before putting on or taking off parts. Do not
adjust the running belt when someone is standing on the unit.
Assemble and operate the treadmill on a solid, level surface. Locate the treadmill a
few feet from walls or furniture. Check the unit before each use and verify that all
fasteners are secure. Maintain the treadmill in good working condition.
Use the treadmill only for its intended use as described in this manual. Do not use
accessory attachments that are not recommended by the manufacturer; such attach-
ments might cause injuries.
If you purchased the optional POLAR
®
chest strap, review the guidelines found in
the
Precor Heart Rate Option Owner’s Manual
that is supplied with that option.
Never operate the unit if it is damaged, if it is not working properly, if it has been
dropped, or if it has been dropped in water. Return the unit to a service center for
examination and repair.
Keep all electrical components such as the motor, power cord, and I/O switch, away
from liquids to prevent shock. Do not set anything on the handrail, display console,
or hood. Place liquids, magazines and books in the appropriate receptacles.
Keep the power cord away from heated surfaces.
Do not operate the treadmill where aerosol (spray) products are being used or where
oxygen is being administered.
Do not use outdoors.
The security clip must be attached at waist level prior to beginning a workout. A cord
connects the security clip to the red STOP button on the console. If a user encoun-
ters difficulties, a strong tug on the security cord or a quick tap on the red STOP
button will stop the running belt.
Use care when getting on or off the treadmill. Use the stationary handrail whenever
possible. Place your feet firmly on the right and left side platforms before the run-
ning belt begins moving (prior to a workout). Step onto the running belt when the
speed is at or below 1 mph (1.6 kph).
IMPORIMPOR
IMPORIMPOR
IMPOR
TT
TT
T
ANT SAFETY INSTRUCTIONSANT SAFETY INSTRUCTIONS
ANT SAFETY INSTRUCTIONSANT SAFETY INSTRUCTIONS
ANT SAFETY INSTRUCTIONS
To reduce the risk of electrical shock, always unplug the unit from its
power source before cleaning or performing any maintenance tasks.
To reduce the risk of burns, fire, electric shock, or injury to
persons, take the following precautions:
IMPORTANT SAFETY INSTRUCTIONS
page 3
COMMERCIAL PRODUCTS DIVISION
Never step off the treadmill while the running belt is moving. Keep your body and
head facing forward. Never attempt to turn around on the treadmill.
Never turn ON the treadmill when someone is standing on the machine.
Never block the air openings on the hood while operating the treadmill. Keep the air
openings clean and free of lint, hair, or anything that might impeded the free flow of
air. Never drop or insert objects into any opening.
Wear proper exercise clothing and shoes during a workout—no loose clothing. Tie
long hair back. Keep all loose towels away from the running surface. The running
belt will not stop immediately if an object becomes caught in the belt or rollers.
Do not rock the unit. Do not stand on the display console or hood.
Do not overexert yourself or work to exhaustion. If you feel any pain or abnormal
symptoms, stop your workout immediately and consult your physician.
SAFETY APPROVAL
When identified with the ETL-c logo, the treadmill has been tested and conforms to the require-
ments of CAN/CSA-E-335-1/3-94, Safety of Household and Similar Electrical Appliances.
GROUNDING INSTRUCTIONS
The C956 or C954 treadmill must be grounded. If it should malfunction or break down, grounding
provides a path of least resistance for electric current which reduces the risk of electrical shock.
The C956 or C954 treadmill is equipped with a power cord having an equipment-grounding
conductor and a grounding plug. The plug must be inserted into an appropriate outlet that is
properly installed and grounded in accordance with all local codes and ordinances. If you do not
follow these
Grounding Instructions
, you could void the Precor limited warranty.
DANGER —
IMPORTANT SAFETY INSTRUCTIONS
SAVE THESE INSTRUCTIONS
IMPORIMPOR
IMPORIMPOR
IMPOR
TT
TT
T
ANT SAFETY INSTRUCTIONSANT SAFETY INSTRUCTIONS
ANT SAFETY INSTRUCTIONSANT SAFETY INSTRUCTIONS
ANT SAFETY INSTRUCTIONS
Diagram 1
Correct power
outlet for U.S.
Markets:
120-volt and
240-volt plugs.
120-volt grounding plug 240-volt grounding plug
120V Units and 240V Units Designated for U.S. Markets
The C956 or C954 treadmill must be connected to a dedicated, grounded circuit. A 20 amp
dedicated circuit is recommended. The treadmill is factory-equipped with a specific power supply
cord to permit connection to a proper electric circuit as shown in Diagram 1. Make sure that the
treadmill is connected to an outlet having the same configurations as the plug. No adapter should
be used with this product.
Improper connection of the equipment-grounding conductor can
result in a risk of electric shock. Check with a qualified electrician
or service person if you are in doubt as to whether the treadmill is properly grounded. Do
not modify the plug provided with the treadmill. If it doesn’t fit the outlet, get a proper outlet
installed by a qualified technician.
page 4
COMMERCIAL PRODUCTS DIVISION
Important Safety Instructions ..........................................2
Safety Approval ..................................................................... 3
Grounding Instructions ........................................................... 3
Radio Frequency Interference (RFI) ........................................ 6
European Applications ........................................................... 6
Obtaining Service ................................................................... 7
About this Manual .................................................................. 7
Unpacking the Treadmill ..................................................8
Standard Equipment ............................................................... 8
Other Equipment .................................................................... 8
Hardware Kit .......................................................................... 9
Setting Up the Treadmill .................................................10
Installation Requirements ....................................................... 10
Additional Tools Needed ......................................................... 10
Assembly Instructions ........................................................... 10
Turning the Unit ON and OFF ................................................. 20
Checking the Alignment of the Running Belt........................... 20
Club Information .............................................................21
Changing the Club Settings .................................................... 21
Selecting the Language .......................................................... 22
Determining the Units of Measure .......................................... 22
Determining the Club Speed Limit .......................................... 23
Setting a Workout Time Limit.................................................. 23
Setting a Pause Time Limit .................................................... 23
Setting a Cool Down Time Limit.............................................. 23
Changing the C956 Custom Courses ...................................... 24
Viewing the Odometer, Hours of Use,
Software Version, and Error Log ............................................. 25
Using CSAFE Standard Equipment ........................................ 25
Table of Contents
page 5
COMMERCIAL PRODUCTS DIVISION
Table of Contents
The C956/C954 Display ..................................................26
Features on the Display Console ............................................ 26
Top Display Windows .............................................................. 27
Upper Display (C956 only) ...................................................... 27
Center Display (C956 and C954) ............................................ 27
Keys on the Display Console.................................................. 28
Keypad Tips ........................................................................... 28
Exercising on the Treadmill............................................33
Using the Security Clip ........................................................... 33
Pause, Cool Down, Summary and Exit Features .................... 33
Quick Steps to Working Out ................................................... 35
Workout Tips .......................................................................... 35
Cooling Down After a Workout ................................................ 36
Courses...........................................................................37
The Heart Rate Features ........................................................ 37
Using the SmartRate
®
Feature ................................................ 37
Manual Mode and the QuickStart Key .................................... 38
C956 Track Course ................................................................. 39
C956 Preprogrammed Courses ............................................... 39
C956 Interval Course .............................................................. 39
C956 Custom Courses ........................................................... 40
C956 Random Course ............................................................ 40
C956 Heart Rate Course ........................................................ 41
C956 Weight Loss Course ...................................................... 42
C956 Goal-based Courses ...................................................... 42
Maintenance ...................................................................43
Inspection .............................................................................. 43
Cleaning the Equipment ......................................................... 43
Aligning the Running Belt ....................................................... 43
Storing the POLAR
®
Chest Strap ........................................... 44
Servicing the Treadmill ........................................................... 45
Long Term Storage ................................................................. 45
C956/C954 Exploded Views ................................................... 46
Warranty Registration Card ..................................................... 53
Warranty ................................................................................. 55
Specifications ............................................................back cover
page 6
COMMERCIAL PRODUCTS DIVISION
RADIO FREQUENCY INTERFERENCE (RFI)
Federal Communications Commission Part 15
The treadmill has been tested and found to comply with:
The IEC EMC Directive (international electromagnetic compatibility certification)
The limits for a Class A digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference in a commercial installation. The treadmill generates, uses, and
can radiate radio frequency energy and, if not installed and used in accor-
dance with the owner’s manual instructions, may cause harmful interference
to radio communications. Operation of the treadmill in a residential area is
likely to cause harmful interference. If this occurs, the user will be required to
correct the interference at his or her own expense.
CAUTION —
Canadian Department of Communications
This digital apparatus does not exceed the Class A limits for radio noise emissions
from digital apparatus set out in the Radio Interference Regulations of the Canadian
Department of Communications.
Le présent appareil numérique n’émet pas de bruits radioéélectriques dépassant les
limites applicables aux appareils numériques de la Class A prescrites dans le
Règlement sur le brouillage radioélectrique édicté par le ministére des Communica-
tions du Canada.
EUROPEAN APPLICATIONS
This product conforms to the requirements of the European Council Directive 89/336/
EEC,
Electromagnetic Compatibility
and has been tested to the following standards:
EN55022, Limits & Methods of Measurement of Radio Interference, Information Tech-
nology Equipment (Class A). Per the standard, the treadmill is a Class A product. In
a domestic environment, this product may cause radio interference, in which case
the user is responsible to take adequate measures to alleviate the interference.
EN50082-1, Generic Immunity Standard for Residential, Commercial and Light
Industrial Products (Class A).
This product additionally conforms to the requirements of the European Council Directive
73/23/EEC,
Low Voltage Directive
and has been tested to the following standard:
IEC 335-1, Safety of Household and similar Electrical Appliances.
Per FCC rules, changes or modifications to the
treadmill not expressly approved by Precor, could
void the user’s authority to operate the equipment.
page 7
COMMERCIAL PRODUCTS DIVISION
OBTAINING SERVICE
Do not attempt to service the treadmill yourself except for the maintenance tasks
described in this manual. The treadmill does not contain any user-serviceable parts.
For information about product operation or service, visit the Precor Web Site at
www.precor.com or contact an authorized Precor Commercial Products Customer
Support Representative at 1-888-665-4404.
To help customer support personnel expedite your call, have your serial number
available. The serial number can be found on the shipping container or on the label
near the power receptacle. If you have any questions regarding the treadmill, use
the model and serial numbers whenever you call a Precor dealer or Commercial
Products Customer Support Representative.
Model number: C956 or C954
Unit number: _____ Serial number: _____________________________
Unit number: _____ Serial number: _____________________________
Unit number: _____ Serial number: _____________________________
ABOUT THIS MANUAL
This manual includes instructions for installing and using the treadmill. To maximize
the use of the treadmill, please study this manual thoroughly. The manual uses the
following conventions for identifying special information:
Note: Contains additional information.
Important: Indicates information to which you should pay special attention.
CAUTION: Indicates steps or information necessary to prevent harm to your-
self or damage to the equipment.
WARNING: Provides instructions to prevent electrical damage to the equip-
ment and injuries to yourself.
DANGER: Indicates steps you must take to prevent electrical shock.
page 8
COMMERCIAL PRODUCTS DIVISION
Thank you for purchasing the Precor C956 or C954 treadmill. Built to the exacting
standards of the health club environment, the treadmill is intended for commercial
use and can withstand the rigors of daily club use with little maintenance.
Important: Before using the treadmill, we urge you to familiarize yourself and
your staff with the entire Owner’s Manual. Understanding this manual will help you
and your customers use the treadmill safely and successfully.
CAUTION: This unit weighs over 350 pounds (158 kilograms). To prevent injury
to yourself or damage to the equipment, obtain appropriate assistance before
removing the unit from the pallet.
The treadmill is carefully inspected before shipment so it should arrive in good
operating condition. Precor ships the unit in the following pieces:
Base frame assembly with hood Hardware kit
Two upright supports Owner’s Manual
Display console with cable Power cord
Two handrails (left and right)
If any items are missing, refer to
Obtaining Service
on page 7.
STANDARD EQUIPMENT
The treadmill incorporates the Precor SmartRate
®
and Heart Rate features into its
display console. Devices, such as FitLinxx
®
, that are CSAFE compatible, can also
be attached.
The Precor “touch” heart rate is standard on the C956 and provides electrode
strips, called “grips, on the center handrail. When a user grasps the metal-portion
of the center handrail, a heart rate is transmitted to the receiver.
Note: If a user does not wish to use the touch-sensitive hand grips, an optional
POLAR
®
chest strap can be purchased and worn. The chest strap transmits the
user’s heart rate and it appears as a number in the HEART RATE display.
Important: The Precor “touch” heart rate is not available on the C954 treadmill,
but the SmartRate
®
and heart rate features will appear on the display if the user
wears the optional POLAR
®
chest strap.
OTHER EQUIPMENT
Optional equipment available through your dealer includes:
POLAR
®
chest strap.
Long handrails.
If you are interested in obtaining Precor option kits for your unit, check with your
dealer. For customer support, see
Obtaining Service
on page 7.
Unpacking the Treadmill
page 9
COMMERCIAL PRODUCTS DIVISION
HARDWARE KIT
After unpacking the treadmill, open the hardware kit and make sure that you have
the following items shown in Diagram 2.
(A) twelve 1-inch buttonhead hex screws
(B) sixteen stainless steel washers — place on 1-inch screws
(C) four ⁵⁄₈-inch flat head hex screws — attach to upper handrails
(D) four 3¹⁄₂-inch socket head screws — install upright supports
(E) four black washers — fasteners for upright supports
(F) four barrel spacers — place on 3¹⁄₂-inch socket head screws after washers
(G) ⁵⁄₃₂-inch hex key — attach handrails to display frame
(H) ³⁄₁₆-inch hex key — attach hood, mount upright supports, attach display
and handrails to base frame
(J) ¹⁄₄-inch hex key — attach upright supports to base mounting brackets
(K) ⁵⁄₁₆-inch hex key — adjust running belt
Note: After assembling the treadmill, be sure to store the hex keys in a secure
place. The tools are used for specific maintenance procedures that are described
in this manual.
Diagram 2
Hardware kit (not shown to scale).
A
C
D
B
E
F
G
H
J
K
page 10
COMMERCIAL PRODUCTS DIVISION
You do not need any special knowledge or experience to set up the treadmill.
However, because of its size and weight, you will need to obtain assistance.
INSTALLATION REQUIREMENTS
Follow these installation requirements when installing the treadmill.
If you do not
install the treadmill according to the following guidelines, you could void the Precor
limited warranty.
Set up the treadmill on a solid, flat surface. Unpack and assemble the treadmill
close to where you plan to use it. Make sure that the flat surface under the unit is
smooth and level. A level unit is required for the user’s safety and proper operation.
Provide ample space around the unit. Open space around the unit makes
for a safer mount and dismount.
Fill out and mail the limited warranty card. The serial number can be found
on the shipping container or on the label near the power receptacle. Write the
serial number onto the Precor limited warranty card found on the back cover of
this manual and in the
Obtaining Service
section on page 7.
Use the appropriate voltage, dedicated circuit, and grounding as speci-
fied on the treadmill. The treadmill is available in both 120-volt and 240-volt
models. Refer to the treadmill’s identification label to determine the voltage
that your treadmill requires. Both the 120-volt and 240-volt models require a
dedicated circuit. A 20 amp circuit is recommended.
CAUTION: Do not use a non-grounded outlet or transformer. Do not
remove or otherwise bypass the plug with an adapter. Electrical damage
can occur and void the Precor limited warranty if the treadmill is
connected to an improper power source. Refer to
Grounding Instructions
on page 3.
ADDITIONAL TOOLS NEEDED
Obtain the following tools
before
assembling the treadmill.
Wire cutter Medium weight string
Bubble level ¹⁄₂-inch box end wrench
SAE standard socket set with a ratchet or 8-inch crescent wrench
ASSEMBLY INSTRUCTIONS
Take the following steps to assemble the treadmill.
CAUTION: To avoid injury and ensure your safety, get assistance before
moving the treadmill off the pallet. Do not drop the unit.
1. Think about the site and location. Have your assistants help place the shipping
carton close to the location where you plan to use the treadmill. Break down the
side walls of the shipping carton so that they lie flat. Remove the loose contents.
2. Make sure that the power switch is OFF. Check the ON/OFF power switch
on the front of the treadmill. Place the switch in the O (OFF) position. Make
sure that the treadmill is not plugged into a power source.
Setting Up the Treadmill
page 11
COMMERCIAL PRODUCTS DIVISION
Diagram 3
Lift the unit by
grasping the
hand holds
inside the rear
end caps.
Lift the rear of the
unit and roll it to
its assembly
location.
Rear end cap
3. Move the treadmill. Diagram 3. Grasp the hand holds inside the rear end
caps and use proper lifting techniques to lift the rear end so that you can roll
the treadmill on its front wheels. To avoid injury to yourself or damage to the
unit, ask for help in maneuvering the treadmill.
Diagram 4
Remove the
hood.
Hood
4. Remove the hood. Diagram 4. Gently, lift the hood off the treadmill and set it
aside.
page 12
COMMERCIAL PRODUCTS DIVISION
5. Attach the left side upright support. Diagram 5. Take the following steps.
a. Remove the shipping fasteners from the front panel. With the supplied hex
key and a 1/2-inch box end wrench, loosen and remove the two bolts and
nuts on the left side of the front panel. These fasteners hold the front panel in
place during shipping. (The front panel will drop slightly when you remove the
fasteners.) Discard the nuts, but keep the bolts.
Diagram 5
Remove the
shipping
fasteners from
the left side front
panel.
Shipping
fasteners found
on left and right
sides of the front
panel.
Diagram 6
Secure the left
upright support.
Screws (D),
washers (E),
and barrel
spacers (F)
b. Attach the left upright support by placing it inside the base mount and align-
ing the mounting holes. Obtain two long sockethead screws (D), washers (E)
and barrel spacers (F) from the Hardware kit. Place a washer and barrel
sleeve on each screw and insert the fasteners through the side of the upright
support and into the base mounts. Use the 1/4-inch hex key to secure the
screws, but leave room for adjustments. See Diagram 6, #1 and #2.
c. Remove two stainless steel washers (B) from the Hardware kit and place
a washer on each of the two shipping fasteners. Reinsert the two shipping
fasteners removed in step 5a, and finger tighten. See Diagram 6, #3.
1 2
Left upright
support
Left side
mounting
bracket
3
Shipping
fasteners with
washers (B)
page 13
COMMERCIAL PRODUCTS DIVISION
CAUTION: To avoid damage to the display cable, read the following steps
carefully. Damage to the cable due to improper assembly is not covered
by the Precor limited warranty.
6. Secure the display console to the left upright support. Diagram 7. Remove
any tape or wire ties that secure the display cable. Unwrap the cable to remove
kinks. Ask an assistant to hold the display console in place while you attach it to
the left upright support using two buttonhead screws (A) with washer (B).
Finger tighten.
Diagram 7
Attach the
display console
to the left upright
support.
Left side
upright support
Screws (A) with
washers (B)
Display cable
Display console
Diagram 8
Remove right
side front panel
screws.
Front panel
fasteners
Right side
mounting bracket
7. Prepare to attach the right side upright. Diagram 8. Take the following steps:
a. Remove the shipping fasteners from the right front panel. Follow the same
process as in step 5a. With the supplied hex key and a ¹⁄₂-inch box end
wrench, loosen and remove the two bolts and nuts on the right side of the
front panel.
page 14
COMMERCIAL PRODUCTS DIVISION
b. Route the display cable through the right upright support. Ask an assistant to
hold the upright support close to the right side mounting bracket. Route the
cable through the upright support (see Diagram 9, #1) and pull it out of the
large hole on the side of the support near its base. Diagram 9, #2.
Note: If you encounter difficulties with the cable, try tying a string to the
end of the cable. Attach a washer to the opposite end for weight and route
it through the upright support.
c. Ask your assistant to position the right upright support inside the base
mounting bracket and align the mounting holes as you pull the cable through
the mounting bracket hole in the base frame. See Diagram 9, #3.
d. Plug the cable connector into its receptacle on the lower board near the
motor. See Diagram 10. A definite “click” is heard when the cable is properly
attached. If you do not hear and feel the connector snap into place, reinsert it.
Diagram 9
Route the cable.
Bracket hole
Base mounting
bracket
Display cable
Right upright
support
1
2
3
Right upright
support
Diagram 10
Connect the
cable.
Lower board
Cable connector
Display cable
Lower board
Base frame
page 15
COMMERCIAL PRODUCTS DIVISION
8. Secure the right side upright support. Diagram 11. Obtain two long sockethead
screws (D), washers (E) and barrel spacers (F) from the Hardware kit. Place a
washer and barrel sleeve on each bolt and insert the fasteners through the
side of the upright support and into the base mounts. Diagram 11, #1. Secure
the upright support using the 1/4-inch hex key. See Diagram 11, #2.
Important: Do not securely tighten the screws until after the unit has been fully
assembled. Make sure that the bolt and spacer do not pinch the cable.
9. Remove two stainless steel washers (B) from the Hardware kit and place one on
each of the two bolts removed in step 7a. Reinsert the bolts and finger tighten.
Diagram 11, #3.
10. Secure the display console to the upright supports. Diagram 12, #1. Align
the display console with the right side upright support mounts. Insert two 1-inch
screws (A) with washers (B) and finger tighten. Use the supplied hex key to
secure the screws on both upright supports, but leave room for adjustments.
See inset in Diagram 12, #2.
Diagram 11
Secure the right
upright support.
Tighten so that
the upright is
secure, but
leave room for
adjustments.
Front panel
Diagram 12
Secure the
display console.
Tighten the
screws, but
leave room for
adjustments.
1-inch screws (A)
with washers (B)
Display console
Screws (D),
washers (E),
and barrel
spacers (F)
1
2
3
Shipping
fasteners with
washers (B)
page 16
COMMERCIAL PRODUCTS DIVISION
Important: With the handrails attached, the width of the treadmill is 36.75
inches (93 cm). It will not fit through a standard 32-inch doorway.
11. Attach the handrails. Diagram 13. For ease of assembly, place the side rails
or adjustable rear feet on blocks. Obtain assistance to lift the treadmill. Do
not place blocks beneath the running bed.
To attach the handrails, perform the following steps on
one side at a time
:
a. Position the handrail as shown in Diagram 13, #1 and #2 and slide it onto the
console extension. Insert two flat head screws (C) into the upper handrail
mounts and finger tighten. See Diagram 13, #3.
b. Align the lower handrail bracket with the two base mounts and insert two
screws (A) with washers (B). See Diagram 13, #4. Tighten the screws with
the hex key. See Diagram 13, #5.
c. Return to the upper handrail screws and securely tighten each one.
d. Perform steps a. through c. on the opposite side.
e. Obtain assistance and remove the blocks from beneath the base.
Diagram 13
Handrail alignment and installation.
3
2
Console
extension
1
4
Handrail
5
Lower
handrail
bracket
Screw (A)
and
washer (B)
Screw (C)
page 17
COMMERCIAL PRODUCTS DIVISION
12. Replace the hood. Diagram 14. Reposition the hood on the treadmill. Remove
four buttonhead screws (A) with washers (B) from the hardware kit. Two
buttonhead screws and washers are placed through the front panel and the
remaining two screws and washers are used to secure the hood to the siderail.
Tighten the screws using the appropriate hex keys.
13. Tighten all mounting screws with the hex keys provided. Diagram 15.
Start at the front of the treadmill with the four screws that attach the upright
supports to the front panel. Tightening these screws first helps pull the rest of
the treadmill’s parts into alignment. Then, proceed with tightening the four
sockethead screws (D) that secure the upright supports, the four console
assembly screws (A), the handrail assembly screws (A) and (C), and the hood
screws (shown in Diagram 14).
Diagram 14
Replace the
hood and
secure it.
Buttonhead
screws (A) with
washers (B)
secure the front
of the hood.
Hood
Diagram 15
Secure the
fasteners and
replace the
hood.
Alternately
tighten the four
front panel
screws.
Alternately tighten
the four screws
that secure the
display console.
Alternately
tighten four
side upright
screws.
Buttonhead
screws (A) with
washers (B)
secure the hood
to the siderail.
1
2
1
2
3
Effective 1 December, 2002
P/N 36286-108
Commercial Equipment Limited Warranty
PLEASE READ THESE WARRANTY TERMS AND CONDITIONS CAREFULLY BEFORE USING YOUR PRECOR INCORPORATED PRODUCT.
BY USING THE EQUIPMENT, YOU ARE CONSENTING TO BE BOUND BY THE FOLLOWING WARRANTY TERMS AND CONDITIONS.
Disclaimer and Release.
The warranties provided herein are the exclusive
warranties given by Precor and supersede any
prior, contrary or additional representations,
whether oral or written.
ANY IMPLIED WARRANTIES,
INCLUDING THE WARRANTY OF MERCHANTABILITY OR
FITNESS FOR A PARTICULAR PURPOSE THAT APPLY
TO ANY PARTS DESCRIBED ABOVE ARE LIMITED IN
DURATION TO THE PERIODS OF EXPRESS WARRAN-
TIES GIVEN ABOVE FOR THOSE SAME PARTS.
PRECOR HEREBY DISCLAIMS AND EXCLUDES THOSE
WARRANTIES THEREAFTER.
Some States do not
allow limitations on how long an implied warranty
lasts, so the above limitation may not apply to you.
PRECOR ALSO HEREBY DISCLAIMS AND EXCLUDES
ALL OTHER OBLIGATIONS OR LIABILITIES, EXPRESS
OR IMPLIED, ARISING BY LAW OR OTHERWISE, WITH
RESPECT TO ANY NONCONFORMANCE OR DEFECT IN
ANY PRODUCT, INCLUDING BUT NOT LIMITED TO:
(A) ANY OBLIGATION, LIABILITY, RIGHT, CLAIM OR
REMEDY IN TORT, WHETHER OR NOT ARISING FROM
THE NEGLIGENCE OF PRECOR OR ITS SUPPLIERS
(WHETHER ACTIVE, PASSIVE OR IMPUTED); AND
(B) ANY OBLIGATION, LIABILITY, RIGHT, CLAIM OR
REMEDY FOR LOSS OF OR DAMAGE TO ANY
EQUIPMENT.
This disclaimer and release shall
apply even if the express warranty set forth
above fails of its essential purpose.
Exclusive Remedies.
For any product described above that fails to
conform to its warranty, Precor will provide, at
their option, one of the following: (1) repair;
(2) replacement; or (3) refund of the purchase
price. Precor Limited Warranty service may be
obtained by contacting the authorized dealer
from whom you purchased the item. Precor
compensates Servicers for warranty trips
within their normal service area to repair
commercial equipment at the customer’s
location. You may be charged a trip charge
outside the service area. THESE SHALL BE THE
SOLE AND EXCLUSIVE REMEDIES OF THE BUYER
FOR ANY BREACH OF WARRANTY.
EXCLUSION OF CONSEQUENTIAL
AND INCIDENTAL DAMAGES.
PRECOR AND/OR ITS SUPPLIERS SHALL HAVE NO
OBLIGATION OR LIABILITY, WHETHER ARISING IN
CONTRACT (INCLUDING WARRANTY), TORT (INCLUD-
ING ACTIVE, PASSIVE, OR IMPUTED NEGLIGENCE
AND STRICT LIABILITY), OR OTHERWISE, FOR
DAMAGE TO THE EQUIPMENT, PROPERTY DAMAGE,
LOSS OF USE, REVENUE OR PROFIT, COST OF
CAPITAL, COST OF SUBSTITUTE EQUIPMENT,
ADDITIONAL COSTS INCURRED BY BUYER (BY WAY OF
CORRECTION OR OTHERWISE) OR ANY OTHER
INCIDENTAL, SPECIAL, INDIRECT, OR CONSEQUEN-
TIAL DAMAGES, WHETHER RESULTING FROM
NONDELIVERY OR FROM THE USE, MISUSE OR
INABILITY TO USE THE PRODUCT. This exclusion
applies even if the above warranty fails of its
essential purposes and regardless of whether
such damages are sought for breach of warranty,
breach of contract, negligence, or strict liability in
tort or under any other legal theory. Some states
do not allow the exclusion or limitation of incidental
or consequential damages, so the above limitation
may not apply to you.
This warranty gives you specific legal rights, and
you may also have other rights, which vary from
state to state.
Complete this portion and keep for your records.
Purchased From: ___________________________ Example: Dealer or store name.
Phone Number: ____________________________ Example: Dealer or store telephone number.
Product/model: _____________________________ Example: EFX534 or 966
Serial number: _____________________________
The serial number is found on the shipping container.
Limited Warranty.
Precor Incorporated warrants all new Precor products to be free from defects in materials and
manufacture for the warranty periods set forth below. The warranty periods commence on the
invoice date of the original purchase. This warranty applies only against defects discovered
within the warranty period and extends only to the original purchaser of the product. Parts
repaired or replaced under the terms of this warranty will be warranted for the remainder of
the original warranty period only. To claim under this warranty, the buyer must notify Precor or
your authorized Precor dealer within 30 days after the date of discovery of any nonconformity
and make the affected product available for inspection by Precor or its service representative.
Precor’s obligations under this warranty are limited as set forth below.
Warranty Periods and Coverage.
Commercial Products, also known as C-Series Products, (excluding
StretchTrainer, Strength Products).
Seven years frame, five years touch sensor display housing, two years parts, one year labor.
For treadmills, five years motor fan, three years drive motor.
For self-powered ellipticals and bikes, one year battery.
Labor coverage for options as defined below.
StretchTrainer
Five years frame, two years parts, 90 days upholstery, no labor.
Strength Products (Catalina 3.45 and Malibu 3.25 only)
Ten years frame; three years bearings, guide rods, cams, pulleys; one year belts, cables,
hand grips, miscellaneous parts; 90 days upholstery; no labor.
Options / Accessories / Battery-powered or Self-Operated Devices
Many options or accessories have components that are connected internally or mounted inside
the electronic console. The following guidelines determine the warranty for these components. If
the internal components are installed by the factory or by an authorized dealer as part of the
original sale and delivery, they have a warranty that is identical to the warranty of the equipment in
which they are connected or mounted. If the internal components are not installed by the factory or
by an authorized dealer as part of the original sale and delivery, they have a 90 days parts and
labor limited warranty. All components that are not internally connected have a
90 days parts only limited warranty. Satisfactory proof of purchase is required in all cases.
Conditions and Restrictions.
This warranty is valid only in accordance with the conditions set forth below:
1. The warranty applies to the Precor product only while
a. it remains in the possession of the original purchaser and proof of purchase is
demonstrated,
b. it has not been subjected to accident, misuse, abuse, improper service, or non-Precor
modification.
c. claims are made within the warranty period.
2. Certain products are warranted for light commercial use only (defined as use in non-fee paying
clubs or facilities and less than 4 hours daily use. Unapproved use voids the warranty. Current
light commercial products include C934, C932, EFX524, EFX534.).
3. This warranty does not cover damage or equipment failure caused by electrical wiring
not in compliance with electrical codes or Precor owner’s manual specifications, or failure
to provide reasonable and necessary maintenance as outlined in the owner’s manual.
4. Except in Canada, Precor does not pay labor outside the United States.
5. Warranties outside the United States and Canada may vary. Please contact
your local Dealer for details.
This Limited Warranty shall not apply to:
1. Software (PROM) version upgrades.
2. Normal wear and tear, consumables and cosmetic items, including, but not limited to
the following: grips, seats, and labels.
3. Repairs performed on Precor equipment missing a serial number or with a serial tag
that has been altered or defaced.
4. Service calls to correct installation of the equipment or instruct owners on how to use
the equipment.
5. Pickup and delivery involved with repairs.
6. Any labor costs incurred beyond the applicable labor warranty period.
55

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Precor C956 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Precor C956 in de taal/talen: Engels als bijlage per email.

De handleiding is 2,31 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info