383782
7
Verklein
Vergroot
Pagina terug
1/11
Pagina verder
POWXQ5302 EN
Copyright © 2015 VARO P a g i n a | 7 www.varo.com
Soft wood: high cutting speed.
When processing metals you should use suitable lubricants/coolants to protect the saw blade
just a little oil for steel, and spirit or petroleum for aluminium, as required. For plastic material
water is normally sufficient as the coolant/lubricant.
8.2 Changing the saw blade (fig 2)
Insert the small hex key through the transparent guard (7) at the side of the tool and
loosen the hex screw.
Slide the blade into the locating groove with teeth pointing forward. Make sure that the
back edge of the blade fits into the guide wheel (8).
Tighten the screw.
8.3 Angle cutting adjustment( fig3)
Loosen the hex head screw located on the underside of the tool using the inner hexagon
spanner provided.
Move the base (12) forward and tilt it until the desired angle is obtained The angle can be
between 0°and 45° (left and right).
Tighten the hex screw.
For accurate cut it is necessary to make a trial cut, measure the work and reset the angle
until the correct setting is achieved.
8.4 Edge guide( fig 4)
With the edge guide you can saw parallel to an edge.
Insert the edge guide (14) into the base (12).
Set the edge guide.
Tighten the screw (13) of edge guide.
8.5 Using the laser (6)
Do not stare directly at the laser (6) beam. Never aim the beam at anyperson
or an object other than the workpiece.
Always ensure the laser beam is aimed at a sturdy work piece without
reflective surfaces i.e. Wood or rough coated surfaces are acceptable.
Bright shiny reflective sheet steel or the like is not suitbale for laser use as
the reflective surface could direct the beam back at the operator.
The laser beam projects a red cutting line on the work piece.
Switch the laser (6) on by means of the on/off switch (5).
Place the machine on the work piece with the saw marking above the start of the cutting
line.
Check that the laser line aligns with the cutting line as marked on the work piece.
Switch on the machine.
After use, switch off the laser.
8.6 Use of pendulum (10)
This jig saw is equipped with four cutting actions, one straight and three orbital. Orbital action
has a more aggressive blade motion and is designed for cutting in soft materials like wood or
plastic. Orbital action provides faster cut, but with a rougher cut across the material. In orbital
action, the blade moves forward during the cutting stroke in addition to the up and down
motion.
Note: Metal or hardwoods should never be cut in orbital action.
7

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Powerplus pow xq 5302 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Powerplus pow xq 5302 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,32 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Powerplus pow xq 5302

Powerplus pow xq 5302 Gebruiksaanwijzing - Nederlands - 11 pagina's

Powerplus pow xq 5302 Gebruiksaanwijzing - Nederlands - 10 pagina's

Powerplus pow xq 5302 Gebruiksaanwijzing - Deutsch - 11 pagina's

Powerplus pow xq 5302 Gebruiksaanwijzing - Français - 12 pagina's

Powerplus pow xq 5302 Aanvulling / aanpassing - Alle talen - 3 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info