645722
8
Verklein
Vergroot
Pagina terug
1/12
Pagina verder
POWX1335LI EN
Copyright © 2014 VARO P a g e | 1 www.varo.com
1 APPLICATION ................................................................................ 3
2 DESCRIPTION (FIG. 1) ................................................................... 3
3 PACKAGE CONTENT LIST ............................................................ 3
4 SYMBOLS ....................................................................................... 3
5 GENERAL SAFETY WARNINGS AND INSTRUCTIONS .............. 4
5.1 Working area .......................................................................................................... 4
5.2 Electrical safety ..................................................................................................... 4
5.3 Personal safety ...................................................................................................... 4
5.4 Power tool use and care ........................................................................................ 5
5.5 Service .................................................................................................................... 5
6 MACHINE-SPECIFIC SAFETY WARNINGS .................................. 5
7 ADDITIONAL SAFETY INSTRUCTIONS FOR BATTERIES AND
CHARGERS .................................................................................... 6
7.1 Batteries (6) ............................................................................................................ 6
7.2 Chargers (5) ........................................................................................................... 6
8 ASSEMBLY ..................................................................................... 7
8.1 Battery charging .................................................................................................... 7
8.2 Charging indication ............................................................................................... 7
8.3 To install or remove the battery pack ................................................................... 7
8.3.1 To remove the battery .............................................................................................. 7
8.3.2 To install the battery ................................................................................................ 7
8.4 Changing the accessory ....................................................................................... 7
8.4.1 Selecting the Application Tool/Accessory ................................................................. 7
8.4.2 Mounting/Replacing the Application Tool/ Accessory ............................................... 8
8.4.3 Mounting/Replacing a Sanding Sheet on the Sanding Plate ..................................... 8
9 OPERATION.................................................................................... 8
9.1 Switching ON/OFF ................................................................................................. 8
9.2 Adjusting the frequency ........................................................................................ 8
9.3 Working Advice...................................................................................................... 8
9.3.1 Sawing..................................................................................................................... 9
9.3.2 Separating ............................................................................................................... 9
POWX1335LI EN
Copyright © 2014 VARO P a g e | 2 www.varo.com
9.3.3 Sanding ................................................................................................................... 9
9.3.4 Scraping .................................................................................................................. 9
10 MAINTENANCE .............................................................................. 9
10.1 General ................................................................................................................... 9
10.2 Service .................................................................................................................. 10
11 STORAGE ..................................................................................... 10
12 TECHNICAL DATA ....................................................................... 10
13 NOISE ............................................................................................ 10
14 WARRANTY .................................................................................. 10
15 ENVIRONMENT ............................................................................ 11
15.1 Battery pack ......................................................................................................... 11
16 DECLARATION OF CONFORMITY ............................................. 12
POWX1335LI EN
Copyright © 2014 VARO P a g e | 3 www.varo.com
LI-ION MULTI-USE TOOL 10.8V
POWX1335LI
1 APPLICATION
Depending on which accessory mounted this power tool is intended for dry sanding small
areas and for sawing, scraping polishing, rasping, cutting and separating.
WARNING! For your own safety, read this manual and the general safety
instructions carefully before using the appliance. Your power tool should
only be given to other users together with these instructions.
2 DESCRIPTION (FIG. 1)
1. Soft grip handle
2. ON/OFF switch
3. Speed control
4. Battery latches
5. Charger
6. Battery
7. Charging stand
8. Sanding plate
9. Sanding sheet
10. Plunge saw blade
11. Stainless steel scraper
12. Segment saw blade
3 PACKAGE CONTENT LIST
Remove all packaging materials.
Remove remaining packaging and packing inserts (if included).
Check that the package contents are complete.
Check the appliance, the power cord, the power plug and all accessories for transportation
damage.
Keep the packaging materials as far as possible until the end of the warranty period. Then
take it to your local waste disposal system.
WARNING Packaging materials are not toys! Children must not play with
plastic bags! There is a danger of suffocation!
1 x Li-Ion Multi-use tool
1 x Li-Ion battery
1 x Hex key
1 x Sanding plate
5 x Sanding sheet
1 x Plunge saw blade
1 x Stainless steel scraper
1 x Segment saw blade
1 x user’s manual
If any parts are missing or damaged, please contact your dealer.
4 SYMBOLS
In this manual and/or on the machine the following symbols are used:
Denotes risk of personal injury
or damage to the tool.
Wear hearing protection.
Read manual before use
Wear eye protection.
POWX1335LI EN
Copyright © 2014 VARO P a g e | 4 www.varo.com
In accordance with essential
requirements of the European
directive(s)
Wear a mask In dusty
conditions
Class II - The machine is
double insulated; Earthing
wire is therefore not
necessary.
5 GENERAL SAFETY WARNINGS AND INSTRUCTIONS
Read all safety warnings and instructions. Failure to heed warnings and follow instructions
may result in electric shock, fire and/or serious injury. Keep safety warnings and instructions
for future reference. The term "power tool" in the safety warnings refers to your mains-
operated (corded) power tool or battery-operated (cordless) power tool.
5.1 Working area
Keep working area clean and well lit. Untidy and dark areas can lead to accidents.
Do not operate power tools in potentially explosive surroundings, for example, in the
presence of inflammable liquids, gases or dust. Power tools create sparks which may
ignite the dust or fumes.
Keep children and bystanders at a distance when operating a power tool. Distractions can
cause you to lose control of it.
5.2 Electrical safety
Always check that the power supply corresponds to the voltage on the
rating plate.
Power tool plugs must match the outlet. Never modify the plug in any way. Do not use
adapter plugs with earthed power tools. Unmodified plugs and matching outlets will reduce
the risk of a lethal electric shock.
Avoid body contact with earthed surfaces such as pipes, radiators, kitchen ranges and
refrigerators. There is an increased risk of a lethal electric shock if your body is earthed.
Do not expose power tools to rain or wet conditions. If water gets inside a power tool, it will
increase the risk of a lethal electric shock.
Do not damage the cord. Never use the cord for carrying, pulling or unplugging the power
tool. Keep the cord away from heat, oil, sharp edges or moving parts. Damaged or
entangled cords increase the risk of a lethal electric shock.
When operating a power tool outdoors, use an extension cable suitable for outdoor use.
Using a cord suitable for outdoor use reduces the risk of a lethal electric shock.
If operating a power tool in a damp location is unavoidable, use a power supply protected
by a residual current device (RCD). Using an RCD reduces the risk of a lethal electric
shock.
5.3 Personal safety
Stay alert, watch what you are doing and use common sense when operating a power
tool. Do not use a power tool when you are tired or under the influence of drugs, alcohol or
medication. A moment of inattention when operating a power tool may result in serious
personal injury.
Use safety equipment. Always wear eye protection. Using safety equipment such as a
dust mask, non-skid safety shoes, a hard hat, or hearing protection whenever it is needed
will reduce the risk of personal injury.
POWX1335LI EN
Copyright © 2014 VARO P a g e | 5 www.varo.com
Avoid accidental starts. Ensure the switch is in the off position before inserting the plug.
Carrying power tools with your finger on the switch or plugging in power tools when the
switch is in the on position makes accidents more likely.
Remove any adjusting keys or spanners before turning on the power tool. A spanner or
key left attached to a rotating part of the power tool may result in personal injury.
Do not reach out too far. Keep your feet firmly on the ground at all times. This will enable
you retain control over the power tool in unexpected situations.
Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and
gloves away from the power tool. Loose clothes, jewellery or long hair can become
entangled in the moving parts.
If there are devices for connecting dust extraction and collection facilities, please ensure
that they are attached and used correctly. Using such devices can reduce dust-related
hazards.
5.4 Power tool use and care
Do not expect the power tool to do more than it can. Use the correct power tool for what
you want to do. A power tool will achieve better results and be safer if used in the context
for which it was designed.
Do not use the power tool if the switch cannot turn it on and off. A power tool with a broken
switch is dangerous and must be repaired.
Disconnect the plug from the power source before making adjustments, changing
accessories, or storing power tools. Such preventive safety measures reduce the risk of
starting the power tool accidentally.
Store power tools, when not in use, out of the reach of children and do not allow people
who are not familiar with the power tool or these instructions to operate it. Power tools are
potentially dangerous in the hands of untrained users.
Maintenance. Check for misalignment or jammed moving parts, breakages or any other
feature that might affect the operation of the power tool. If it is damaged, the power tool
must be repaired. Many accidents are caused by using poorly maintained power tools.
Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting
edges are less likely to jam and are easier to control.
Use the power tool, accessories and cutting tools, etc., in accordance with these
instructions and in the manner intended for the particular type of power tool, taking into
account the working conditions and the work which needs to be done. Using a power tool
in ways for which it was not intended can lead to potentially hazardous situations.
5.5 Service
Your power tool should be serviced by a qualified specialist using only standard spare
parts. This will ensure that it meets the required safety standards.
6 MACHINE-SPECIFIC SAFETY WARNINGS
Use the machine only for dry sanding. Penetration of water into the machine increases the
risk of an electric shock.
Keep hands away from the sawing range. Do not reach under the workpiece. Contact with
the saw blade can lead to injuries.
Use suitable detectors to determine if utility lines are hidden in the work area or call the
local utility company for assistance. Contact with electric lines can lead to fire and electric
shock. Damaging a gas line can lead to explosion. Penetrating a water line causes
property damage or may cause an electric shock.
When working with the machine, always hold it firmly with both hands and provide for a
secure stance. The power tool is guided more secure with both hands.
Secure the workpiece. A workpiece clamped with clamping devices or in a vice is held
more secure than by hand.
Keep your workplace clean. Blends of materials are particularly dangerous. Dust from light
alloys can burn or explode.
POWX1335LI EN
Copyright © 2014 VARO P a g e | 6 www.varo.com
Avoid unintentional switching on. Ensure the On/Off switch is in the off position before
inserting battery pack. Carrying the power tool with your finger on the On/Off switch or
inserting the battery pack into power tools that have the switch on invites accidents.
Do not open the battery. Danger of short-circuiting. Protect the battery against heat, e.g.,
also against continuous sun irradiation and fire. There is danger of explosion.
In case of damage and improper use of the battery, vapours may be emitted. Provide for
fresh air and seek medical help in case of complaints. The vapours can irritate the
respiratory system.
When the battery is defective, liquid can escape and come into contact with adjacent
components. Check any parts concerned. Clean such parts or replace them, if required.
Use the battery only in conjunction with your power tool. This measure alone protects the
battery against dangerous overload.
Wear protective gloves when changing application tools/accessories.
Application tools/ accessories become hot after prolonged usage.
Do not scrape wetted materials (e. g. wallpaper) or on moist surfaces. Penetration of water
into the machine increases the risk of an electric shock.
Do not treat the surface to be worked with solvent-containing fluids. Materials being
warmed up by the scraping can cause toxic vapours to develop.
Exercise extreme caution when handling the scraper. The accessory is very sharp; danger
of injury.
7 ADDITIONAL SAFETY INSTRUCTIONS FOR BATTERIES AND
CHARGERS
7.1 Batteries (6)
Never attempt to open for any reason.
Do not store in locations where the temperature may exceed 40 °C.
Charge only at ambient temperatures between 4 °C and 40 °C.
Charge only using the charger provided with the tool.
When disposing of batteries, follow the instructions given in the section “Protecting the
environment”.
Do not cause short circuits. If connection is made between the positive (+) and negative (-)
terminal directly or via accidental contact with metallic objects, the battery is short circuited
and an intense current will flow causing heat generation which may lead to casing rupture
or fire.
Do not heat. If batteries are heated to above 100 °C, sealing and insulating separators
and other polymer components may be damaged resulting in electrolyte leakage and/or
internal short circuiting leading to heat generation causing rupture or file. Moreover do not
dispose of the batteries in fire, explosion and/or intense burning may result.
Under extreme conditions, battery leakage may occur. When you notice liquid on the
battery, proceed as follows:
Carefully wipe the liquid off using a cloth. Avoid skin contact.
In case of skin or eye contact, follow the instructions below:
o Immediately rinse with water. Neutralize with a mild acid such
as lemon juice or vinegar.
o In case of eye contact, rinse abundantly with clean water for at
least 10 minutes. Consult a physician.
Fire hazard! Avoid short-circuiting the contacts of a detached battery. Do
not incinerate the battery.
7.2 Chargers (5)
Use the charger provided with the tool only to charge the battery
POWX1335LI EN
Copyright © 2014 VARO P a g e | 7 www.varo.com
Never attempt to charge non-rechargeable batteries.
Have defective cords replaced immediately.
Do not expose to water.
Do not open the charger.
Do not probe the charger.
The charger is intended for indoor use only.
8 ASSEMBLY
8.1 Battery charging
Use only the battery charger supplied with your tool. Only these battery chargers are matched
to the lithium ion battery of your power tool.
Note: The battery is supplied partially charged. To ensure full capacity of
the battery, completely charge the battery in the battery charger before
using your power tool for the first time. The lithium ion battery can be
charged at any time without reducing its service life. Interrupting the
charging procedure does not damage the battery.
8.2 Charging indication
The charger has two LED light (red and green). The green one is the power indicator.
When the charger is plugged in, this will light up.
When properly connected, the green and red light is lit continuously, this means the battery is
charging.
When the battery is fully loaded, the green light is continuously lit and the red light is out.
If the green and red light flash alternating, a malfunction occurs.
8.3 To install or remove the battery pack
8.3.1 To remove the battery
Depress both the battery release buttons and gently pull the battery out of the tool.
8.3.2 To install the battery
Hold the tool upright in one hand and the battery in your other hand. While pressing with two
fingers on the battery release buttons, insert the battery until it clicks into place. Do not use
excessive force when inserting the battery. If the battery does not slide in easily, it is not being
inserted correctly. It is also possible that there could be damage to the battery, battery
terminals or the tool.
8.4 Changing the accessory
Before any work on the machine itself (e.g. maintenance, accessory
change, etc.) as well as during transport and storage, remove the battery
from the power tool. There is danger of injury when unintentionally
actuating the On/Off switch.
Wear protective gloves when changing application tools/accessories.
Contact with the application tool/accessoriy can lead to injuries.
8.4.1 Selecting the Application Tool/Accessory
Accessory
Material
POWX1335LI EN
Copyright © 2014 VARO P a g e | 8 www.varo.com
Plunge saw blade (10)
Wooden materials, plastic,
gypsum and other soft materials.
Segment saw blade(12)
Wooden materials, plastic, non-
ferrous metals.
Stainless steel scraper (11)
Wood, paint, carpet adhesive,
silicone and other elastic
materials.
Sanding plate (8)
Depends on sanding sheet (9)
8.4.2 Mounting/Replacing the Application Tool/ Accessory
If required, remove an already mounted application tool/accessory.
For removing the application tool/accessory, loosen the screw with the hex key and
remove the application tool/accessory.
Mount the requested application tool/accessory in such a manner on the tool holder that
the offset faces downward.
Turn the application tool/accessory to a position favourable for the respective job, and
allow it to engage into the cams of the tool holder.
Fasten the application tool/accessory with the flange screw. Tighten the flange screw with
hex key until the flange screw faces flush against the application tool/accessory.
Check the tight seating of the application tool/accessory. Incorrect or not
securely fastened application tools/accessories can come loose during
operation and pose a hazard.
8.4.3 Mounting/Replacing a Sanding Sheet on the Sanding Plate
The sanding plate is fitted with Hook & loop backing for quick and easy fastening of
sanding sheets with Hook & loop adhesion.
Before attaching the sanding sheet, free the Hook & loop backing of the sanding plate
from any debris by tapping against it in order to enable optimum adhesion.
Position the sanding sheet flush alongside one edge of the sanding plate, then lay the
sanding sheet onto the sanding plate and press firmly.
To remove the sanding sheet, grasp it at one of the tips and pull it off from the sanding
plate.
9 OPERATION
9.1 Switching ON/OFF
Make sure the fully charged battery pack is installed.
Switch the power tool on: push the ON/OFF switch button forwards to the “ON” position.
Switch the power tool off: pull the ON/OFF switch button backwards to the “OFF” position.
9.2 Adjusting the frequency
Adjust the frequency according to the application before beginning with the work. For example,
we recommend a high frequency for work with the scraper. Conduct a test run in order to find
a suitable frequency.
The frequency controller can be set at 6 positions. The “1”position indicates the lowest
frequency and the“6”position indicates the highest. The operator may have to vary the speed
to optimize cutting efficiency.
9.3 Working Advice
POWX1335LI EN
Copyright © 2014 VARO P a g e | 9 www.varo.com
9.3.1 Sawing
Use undamaged faultless saw blades only. Deformed, blunt saw blades or
saw blades that are otherwise damaged can break.
Plunge cuts may only be applied to soft materials, such as wood, gypsum
plaster boards, etc.!
Before sawing with saw blades in wood, particle board, building materials, etc., check these
for foreign objects such as nails, screws, or similar. If required, remove foreign objects or use
saw blades for metal.
9.3.2 Separating
Note: When separating wall tiles take into consideration that the application tools/accessories
wear heavily when used for longer periods of time.
9.3.3 Sanding
The removal rate and the sanding pattern are primarily determined by the choice of sanding
sheet, the preset oscillation rate and the applied pressure.
Only flawless sanding sheets achieve good sanding capacity and extend the service life of the
machine.
Pay attention to apply uniform sanding pressure; this increases the working life of the sanding
sheets.
Intensifying the sanding pressure does not lead to an increase of the sanding capacity, but to
increased wear of the machine and the sanding sheet.
For precise on-the-spot sanding of edges, corners and hard to reach areas, it is also possible
to work only with the tip or an edge of the sanding plate.
When selectively sanding on the spot, the sanding sheet can heat up considerably. Reduce
the orbital stroke rate and allow the sanding sheet to cool down regularly.
A sanding sheet that has been used for metal should not be used for other materials.
9.3.4 Scraping
For scraping, select a high oscillation rate.
Work on a soft surface (e.g. wood) at a flat angle and apply only light pressure. Otherwise the
scraper can cut into the surface.
10 MAINTENANCE
10.1 General
Your tool has been designed to operate over a long period of time with a minimum of
maintenance.
Continuous satisfactory operation depends upon proper tool care and regular cleaning.
Clean your tool using a damp cloth.
Your charger does not require any maintenance apart from regular cleaning, unplug it
before cleaning.
Use a soft brush or dry cloth.
KEEP VENTILATION SLOTS CLEAN! Periodically check the air vents for dust or other
debris. Clean with compressed air (max. 3 bar)
Do not use any abrasive or solvent-based cleaner. Use clean cloths to remove dirt, carbon
dust, etc.
POWX1335LI EN
Copyright © 2014 VARO P a g e | 10 www.varo.com
WARNING: Do not allow brake fluids, gasoline, petroleum-based products, penetrating oils,
etc. come in contact with plastic parts, they contain chemicals that can damage, weaken or
destroy plastic.
WARNING: Always wear safety goggles or safety glasses with side shields when using
compressed air to clean tools. If the operation is dusty, also wear a dust mask.
BATTERIES: The battery pack for this tool is equipped with a Li-ion
rechargeable battery. Do not disassemble battery pack and attempt to
replace the batteries inside.
10.2 Service
Have your power tool serviced by a qualified repair person using only identical replacement
parts. This will ensure that the safety of the power tool is maintained.
11 STORAGE
Store your tool in a clean, dry, frost free environment.
Battery storage
Store your batteries in a cool area. Optimal temperature for storing your Li-ion battery for
longer term is 2°C. (capacity loss will only be 6% / year (compared to 20% at 25°C)).
Never store batteries in discharged condition.
It is better for Li-ion batteries to recharge them frequently. Optimal long time storage
charge for your Li-ion battery is at 40% of their capacity.
12 TECHNICAL DATA
POWX1335LI
10.8V
5000-19000min
-1
Li-Ion
1500 mAh
230 V 50 Hz
3-5 hour
13 NOISE
Noise values measured according to relevant standard. (K=3)
Acoustic pressure level LpA
82 dB (A)
Acoustic power level LwA
93 dB (A)
ATTENTION! The sound power level may exceed 85 dB(A), in this case
individual hearing protection shall be worn.
aw (Vibration)
Max 5.4 m/s²
K = 1.5 m/s²
14 WARRANTY
This product is warranted for a 36-month period effective from the date of purchase by the
first user.
This warranty covers all material or production flaws excluding : batteries, chargers,
defective parts subject to normal wear & tear such as bearings, brushes, cables, and
plugs, or accessories such as drills, drill bits, saw blades, etc. ; damage or defects
resulting from maltreatment, accidents or alterations; nor the cost of transportation.
Damage and/or defects resulting from inappropriate use also do not fall under the
warranty provisions.
POWX1335LI EN
Copyright © 2014 VARO P a g e | 11 www.varo.com
We also disclaim all liability for any bodily injury resulting from inappropriate use of the
tool.
Repairs may only be carried out by an authorized customer service centre for Powerplus
tools.
You can always obtain more information at the number 00 32 3 292 92 90.
Any transportation costs shall always be borne by the customer, unless agreed otherwise
in writing.
At the same time, no claim can be made on the warranty if the damage of the device is the
result of negligent maintenance or overload.
Definitely excluded from the warranty is damage resulting from fluid permeation, excessive
dust penetration, intentional damage (on purpose or by gross carelessness), inappropriate
usage (use for purposes for which the device is not suitable), incompetent usage (e.g. not
following the instructions given in the manual), inexpert assembly, lightning strike,
erroneus net voltage. This list is not exhaustive.
Acceptance of claims under warranty can never lead to the prolongation of the warranty
period nor commencement of a new warranty period in case of a device replacement.
Devices or parts which are replaced under the warranty therefore remain the property of
Varo NV.
We reserve the right to reject a claim whenever the purchase cannot be verified or when it
is clear that the product has not been properly maintained. (Clean ventilation slots, carbon
brushes serviced regularly, etc.).
Your purchase receipt must be kept as proof of date of purchase.
Your appliance must be returned undismantled to your dealer in an acceptably clean state,
(in its original blow-moulded case if applicable to the unit), accompanied by proof of
purchase.
Your tool must be charged at least 1x per month to ensure optimal operation of this tool.
15 ENVIRONMENT
Should your appliance need replacement after extended use, do not dispose of it
with the household refuse, but in an environmentally safe way.
Waste of electrical products should not be disposed of with household waste.
Please recycle where facilities exist. Check with your Local Authority or retailer for
recycling advice.
15.1 Battery pack
This product contains Li-ion. To preserve natural resources, please recycle or dispose of
batteries properly. Local, state or federal laws may prohibit disposal of Li-ion batteries in
ordinary trash. Consult you local waste authority for information regarding available recycling
and/or disposal options.
POWX1335LI EN
Copyright © 2014 VARO P a g e | 12 www.varo.com
16 DECLARATION OF CONFORMITY
VARO N.V. - Joseph Van Instraat 9 - BE2500 Lier - BELGIUM, declares that,
Product: Cordlessmulti-use tool
trade mark: POWERplus
model : POWX1335LI
is in conformity with the essential requirements and other relevant provisions of the applicable
European Directives, based on the application of European harmonized standards. Any
unauthorized modification of the apparatus voids this declaration.
European Directives (including, if applicable, their amendments up to the date of signature);
2004/108/EEC
2006/42/EC
2011/65/EU
European harmonized standards (including, if applicable, their amendments up to the date of
signature);
EN60745-1 : 2009
EN60745-2-4 : 2009
EN55014-1 : 2006
EN55014-2 : 1997
Keeper of the Technical Documentation : Philippe Vankerkhove, VARO Vic. Van Rompuy
N.V.
The undersigned acts on behalf of the company CEO,
Hugo Cuypers
Regulatory Affairs Compliance Manager
Date : 04/07/2014
8

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Powerplus POWX1335LI bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Powerplus POWX1335LI in de taal/talen: Engels als bijlage per email.

De handleiding is 0,38 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

Andere handleiding(en) van Powerplus POWX1335LI

Powerplus POWX1335LI Gebruiksaanwijzing - Nederlands - 13 pagina's

Powerplus POWX1335LI Gebruiksaanwijzing - Deutsch - 13 pagina's

Powerplus POWX1335LI Gebruiksaanwijzing - Français - 13 pagina's

Powerplus POWX1335LI Aanvulling / aanpassing - Alle talen - 1 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info