677891
12
Verklein
Vergroot
Pagina terug
1/23
Pagina verder
POWX0760 EN
Copyright © 2014 VARO NV P a g e | 12 www.varo.com
9.2 Table height two-way set up
The table height can be set up in two ways, high or low table.
WARNING: Before falling down the tool backwards, always set the tool in
the Mitre saw mode and lock the tool head in the lowest position.
9.2.1 High table set up (Fig. 18)
To set up the tool with high table, proceed as follows.
Fall down the tool carefully BACKWARDS without fail while holding it with both hands.
Fix the 4 legs using a bolt, wing nut and the U-shaped customized washer.
9.2.2 Low table set up (Fig. 19)
Fold in the 4 legs. To do so :
Fall down the tool carefully BACKWARDS without fail while holding it with both hands.
untighten the wing nut of each leg seperatly until you can turn the leg 90° , aligned with
tabel. Then tigthen the wing nut again
Return the tool to the upright position.
9.3 Installing or removing saw blade
CAUTION:
Always be sure that the tool is switched off and unplugged before installing or removing
the blade.
Use only the socket wrench provided to install or remove the blade. Failure to do so may
result in overtightening or insufficient tightening of the hex bolt. This could cause an injury.
Move up the handle in the fully raised position. Press the shaft lock to lock the spindle, use
the socket wrench to loosen the hex bolt clockwise. (Fig. 20) Raise the blade guard A with
its lifting lever while pushing the lever nearby the handle to the left. With the blade guard A
raised, remove the hex bolt, outer flange and blade. (Fig. 21) To install the blade, mount it
carefully onto the spindle, making sure that the direction of the arrow on the surface of the
blade matches the direction of the arrow on the blade case. Install the outer flange and
hex bolt, and then use the socket wrench to tighten the hex bolt (lefthanded) securely
counterclockwise while pressing the shaft lock.
NOTE: When installing a saw blade, be sure to insert it between the blade
guard (7) at first and then raise it so that the blade is finally placed in the
blade guard. (Fig. 22 & 23)
CAUTION:
The ring 30 mm in outer diameter is factory-installed between the inner and outer flanges.
Return the lower blade guard (8) to its original position. Lower the handle to make sure
that the lower blade guards move properly. Make sure shaft lock has released spindle
before making cut.
9.4 Adjusting riving knife (fig 25,26 & 27)
There must be a clearance of about 5 6 mm between the riving knife and the blade teeth
when pushing riving knife toward the blade fully. Adjust the riving knife accordingly by first
loosening clamping nut by hand counterclockwise and then loosening hex bolt
counterclockwise with the hex socket wrench, and measuring the distance. After adjustment,
securely tighten the hex bolt and then the clamping nut clockwise. Always check to see that
the riving knife is secured and that the top blade guard works smoothly before cutting.
12

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Powerplus POWX0760 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Powerplus POWX0760 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,46 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Powerplus POWX0760

Powerplus POWX0760 Gebruiksaanwijzing - Nederlands - 26 pagina's

Powerplus POWX0760 Gebruiksaanwijzing - Deutsch - 27 pagina's

Powerplus POWX0760 Gebruiksaanwijzing - Français - 26 pagina's

Powerplus POWX0760 Aanvulling / aanpassing - Alle talen - 12 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info