Handleiding Powerplus POWAIR0806 (pagina 4 van 7) (Engels)

582125

Verklein

Vergroot

Pagina terug

1/7

Pagina verder

POWAIR0806 EN

1 APPLIANCE ....................................................................................................2

2 DESCRIPTION .................................................................................................2

3 PACKAGE CONTENT LIST ............................................................................2

4 SAFETY RULES (FIG. B) ................................................................................2

5 LUBRICATION ................................................................................................3

6 IMPORTANT!!! ................................................................................................4

7 TOOL USE .......................................................................................................4

8 MAINTENANCE ...............................................................................................4

9 TECHNICAL DATA .........................................................................................5

10 NOISE ..............................................................................................................5

11 TROUBLESHOOTING .....................................................................................5

12 ENVIRONMENT ...............................................................................................6

13 DECLARATION OF CONFORMITY ................................................................7

POWAIR0806 EN

PNEUMATIC 2 IN 1 COMBI NAILER

POWAIR0806

1 APPLIANCE

Use for almost any finish, furniture, cabinetry, paneling, trim, or craft application

Warning Read this manual and general safety instructions carefully before

using the appliance, for your own safety.

2 DESCRIPTION

1. Trigger exhaust vent

2. ¼” coupler

3. Magazine lock

4. Magazine

5. Nailer nose

6. Trigger

3 PACKAGE CONTENT LIST

 Remove all packaging materials.

 Remove remaining packaging and packing inserts (if included).

 Check that the package contents are complete.

 Check the appliance, the power cord, the power plug and all accessories for

transportation damage.

 Keep the packaging materials as far as possible until the end of the warranty period.

Then take it to your local waste disposal system.

WARNING Packaging materials are not toys! Children must not play with

plastic bags! There is a danger of suffocation!

1 x 2 in 1 combi nailer

2 x keys

1000 x 50mm nails

1000 x 40mm staples

1 x male Euro coupler

1 x male Orion coupler

1 x oil bottle (empty)

1 x PTFE sealing tape

1 x CE goggles

1 x BMC

1 x Manual

If any parts are missing or damaged, please contact your dealer.

4 SAFETY RULES (FIG. B)

 Use only following fixing devices:

 Ga. 18 nail & staple

 Nails length: 15-50mm

 Staple crown: 5.7mm

 Staple length: 16-40mm

 Tools with an inverted triangle can only be used with security elements: this

stapler/nailer is equipped with a safety yoke.

POWAIR0806 EN

 To prevent injuries to yourself and bystanders, refer to tool use, maintenance and

troubleshooting sections for additional information (fig 1)

 To prevent eye injuries, always wear safety glasses with hard plastic side shields. Be

sure everyone in your work area is wearing the same type of safety glasses (fig 2)

 Always wear hearing protection and hard hat. (fig 3)

 Never use hydrogen oxygen, carbon dioxide or any other bottled gas as a power

source for this tool, the tool will explode and cause serious injury. (fig4)

 Remove finger from trigger when not driving fasteners. Never carry tool with finger on

trigger, tool will eject fastener If safety is bumped. (fig5)

 Never conned tool to an air hose with pressure exceeds 200 psi or 13.7 BAR (fig6)

 Air compressors must comply with requirement ANSI B19.3 1981 (U.S.), "Safety

Standard For Compressors For Process Industries." (fig 7)

 Air hose minimum working pressure rating of 150 psi (10.3 BAR) or 150% of the

maximum pressure produced in the system is absolutely necessary. (fig 8)

 The tool and air supply hose must have a hose coupling such that all pressure is

removed from the tool when the coupling Joint is disconnected. (fig 9)

 Use only compressed air coming through 3 pieces set. (fig 10)

 Never load fastener before tool connected to air supply (fig 11)

 Never use tool if safety element, trigger or springs have become inoperative, missing or

damaged, It is hazardous to remove safety element, trigger or spring. (fig 12)

 Before using this tool, make sure trigger, screw and cap are securely tightened. (fig 13)

 Do not modify tool without authorization. (fig 14)

 Disconnect tool from air whenever the tool stops working (fig15)

 Keep the tool pointed away from yourself and others. (fig 16)

 Fire fasteners into work surface only, never into materials too hard to penetrate. (fig 17)

 Do not drive fasteners on top of other fasteners. Tool fired in an inclined angle is also

forbidden. (fig 18)

 Do not push safety element on work surface until a second fastener is desired (fig 19)

 Do not drive fasteners close to the edge of the work surface. The work piece is likely to

split and the fastener could fly free and hit someone. (fig 20)

 Do not load fasteners with trigger or safety element depressed. (fig 21)

 Do not use tool without Danger label on tool. (fig 22)

 Never use a tool that leaks air or needs repair. (fig 23)

 Be sure you are in a balanced position when using or handling the tool (fig 24)

 Operate tool at recommended pressure of 4-8 bar

5 LUBRICATION

An automatic in-line filter-regulator-lubricator is recommended (Fig 1) as it increases tool

life and keeps the tool in sustained operation. The in-line lubricator should be regularly

checked and filled with air tool oil.

Proper adjustment of the in-line lubricator is performed by placing a sheet of paper next to

the exhaust ports and holding the throttle open approximately 30 seconds. The lubricator

is properly set when a light stain of oil collects on the paper. Excessive amounts of oil

should be avoided.

In the event that it becomes necessary to store the tool for an extended period of time

(overnight, weekend, etc.), it should receive a generous amount of lubrication at that time.

The tool should be run for approximately 30 seconds to ensure oil has been evenly

distributed throughout the tool. The tool should be stored in a clean and dry environment.

POWAIR0806 EN

 It is most important that the tool be properly lubricated by keeping the air line lubricator

filled and correctly adjusted. Without proper lubrication the tool will not work properly

and parts will wear prematurely.

 Use the proper lubricant in the air line lubricator. The lubricator should be of low air flow

or changing air flow type, and should be kept filled to the correct level. Use only

recommended lubricants, specially made for pneumatic applications. Substitutes may

harm the rubber compounds in the tools, O-rings and other rubber parts.

6 IMPORTANT!!!

If no filter/ pressure regulator/ lubricator is installed in the compressed air system, then

pneumatic tools must be lubricated with 2 to 6 drops of oil at least once a day or after

every two hours of use. This must be done directly along the male coupler or the screw

(OIL) provided for the purpose on the side of the tool’s housing.

Automatic lubrication is also possible using the supplied mini oiler that you have to install

between the threaded connector of the tool and the male coupler. Make sure that the oiler

is always filled with suitable oil.

Fig. 1

1. Tool

2. Quick connector

3. Quick coupler

4. Air hose

5. Quick connector

6. Quick coupler

7. Lubricator

8. Regulator (0-8.5 bar)

9. Filter

10. Cut-off valve

11. Air compressor

7 TOOL USE

1. Read "Safety Warnings" before using tool

2. Push magazine lock lever and slide upper magazine to open magazine. (Fig. 2)

3. Place strip of nails or staples into the magazine with the point resting on the fastener

guide. Do not load with trigger depressed. (Fig. 3)

4. Push upper magazine back until magazine lock latches. (Fig. 4)

5. Keep the nailer pointed away from yourself and others and connect to the hose.

6. Position the nailer nose against work piece and pull the trigger

7. Disconnect air supply in case a nail or stapler is jammed

8. Loosen screws on the nose with the hex key and remove the front part. (Fig. 5)

Remove jammed nails or staples and close the front cover.

9. Keep the tool pointed away from yourself and others and connect back to the hose.

8 MAINTENANCE

Disconnect the tool from the compressor before adjusting, clearing jams,

servicing &maintenance, relocating and during non operation.

 Regular lubrication, if your tool without using the in-liner automatic oilier, place 2 or 6

drops of pneumatic tool oil into the air inlet before each work day or after 2 hours of

continuous use depending in the characteristic of work piece or type of fasteners.

POWAIR0806 EN

 Air-operated tools must be inspected periodically, and worn or broken parts must be

replaced to keep the tool operating safely and efficiently. Check and change all worn or

damaged O-ring, Seals, etc. Tight all the screws and caps in case personal injury.

 Make regular inspection for free movement of trigger, Spring and safety mechanism to

assure safe system is complete and functional: no loose and missing parts, no building

or stocking parts.

 Keep magazine and nose of tool clean and free of any dirt lint or abrasive particles.

 When temperatures are below freezing, tools should be kept warm by any convenient,

safe method.

9 TECHNICAL DATA

Model

POWAIR0806

Activation mode

Single sequential action

Max. allowable pressure

120PSI(8.3 bar)

Operating pressure

60-100PSI(4-7bar)

Air inlet size

¼”

Avg. air consumption

65l/min(2.29cfm)

Recommended lubricant

White mineral oil

Nail capacity

100pcs

10 NOISE

Noise emission values measured according to relevant standard. (K=2.5)

Acoustic pressure level LpA

89 dB(A)

Acoustic power level LwA

102 dB(A)

ATTENTION! Wear hearing protection when sound pressure is over 85

dB(A).

aw (Vibration) :

1.9 m/s²

K= 0.5 m/s²

11 TROUBLESHOOTING

SYMPTOM

PROBLEM

SOLUTIONS

Air leak

near top of tool or in

trigger area

O-ring in trigger valve is

damaged.

Check and replace O-ring.

Trigger valve head are

damage.

Check and replace.

Trigger valve stem, seal or

O-ring are damaged.

Check and replace trigger

valve stem, seal or O-ring

Air leak near bottom of

tool.

Loose screws.

Tighten screws.

Worn or damaged O-rings or

bumper.

Check and replace O-rings

or bumper.

Air leak between body

Loose screws.

Tighten screw.

POWAIR0806 EN

and cylinder cap.

Worn or damaged O-rings or

seals.

Check and replace O-rings

or bumper.

Blade driving fastener

too deep.

Worn bumper.

Replace bumper.

Air pressure is too high.

Adjust the air pressure.

Tool does not operate

well: can not drive

fastener or operate

sluggishly.

Inadequate air supply.

Verify adequate air supply.

Inadequate lubrication.

Place 2 or 6 drops of oil into

air inlet.

Worn or damaged O-rings or

seals.

Check and replace O-rings

or seal.

Exhaust port in cylinder head

is blocked.

Replace damaged internal

parts.

Tool skips fasteners.

Worn bumper or damaged

spring.

Replace bumper or pusher

spring.

Dirt in front plate.

Clean drive channel on front

plate.

Dirt or damage prevents

fasteners from moving freely

in magazine.

Magazine needs to be

cleaned.

Worn or dry O-ring on piston

or lack of Lubrication.

O-ring needs to be replaced

and lubricate.

Cylinder covers seal leaking.

Replace Sealing washer.

Tool jams.

Incorrect or damaged

fasteners.

Change and use correct

fastener.

Damaged or worn driver

guide.

Check and replace the

driver.

Magazine or nose screw

loose.

Tighten the magazine.

Magazine is dirty.

Clean the magazine.

12 ENVIRONMENT

Should your appliance need replacement after extended use, do not discard it with the

household rubbish but dispose of it in an environmentally safe way.

POWAIR0806 EN

13 DECLARATION OF CONFORMITY

VARO N.V. - Joseph Van Instraat 9 - BE2500 Lier - BELGIUM, declares that,

product: Pneumatic 2 in 1 combi nailer

trade mark: POWERplus

model: POWAIR0806

is in conformity with the essential requirements and other relevant provisions of the

applicable European Directives, based on the application of European harmonized

standards. Any unauthorized modification of the apparatus voids this declaration.

European Directives (including, if applicable, their amendments up to the date of

signature);

2006/42/EC

European harmonized standards (including, if applicable, their amendments up to the date

of signature);

EN792-13: 2000

Keeper of the Technical Documentation : Philippe Vankerkhove, VARO – Vic. Van

Rompuy N.V.

The undersigned acts on behalf of the company CEO,

Hugo Cuypers

Regulatory Affairs – Compliance Manager

Date: 29/01/2014

Powerplus POWAIR0806 Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Andere handleiding(en) van Powerplus POWAIR0806

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info