Handleiding Powerplus POWAIR0312 (pagina 1 van 12) (Engels)

795740

Verklein

Vergroot

Pagina terug

1/12

Pagina verder

  POWAIR0312  EN 
Copyright © 2022 VARO  P a g e  | 1  www.varo.com 
INTENDED USE ..............................................................................................2 
DESCRIPTION (FIG. A) ...................................................................................2 
PACKAGE CONTENT LIST ............................................................................2 
SYMBOLS .......................................................................................................3 
GENERAL POWER TOOL SAFETY WARNINGS ..........................................3 
1 Working area ..................................................................................................3 
2 Electrical safety ..............................................................................................3 
3 Personal safety ...............................................................................................4 
4 Power tool use and care ................................................................................4 
5 Service ............................................................................................................5 
SPECIAL SAFETY INSTRUCTIONS FOR ELECTRIC STAPLERS ...............5 
SAFETY RULES (FIG. B) ................................................................................5 
TOOL USE .......................................................................................................6 
LUBRICATION ................................................................................................7 
1 Depth adjustment (fig. 1) ...............................................................................8 
MAINTENANCE ...............................................................................................8 
TECHNICAL DATA .........................................................................................9 
NOISE ..............................................................................................................9 
TROUBLESHOOTING .....................................................................................9 
WARRANTY ..................................................................................................10 
ENVIRONMENT .............................................................................................11 
DECLARATION OF CONFORMITY ..............................................................12 
 

POWAIR0312 EN

PNEUMATIC 2 IN 1 COMBI NAILER

POWAIR0312

1 INTENDED USE

Use for almost any finish, furniture, cabinetry, paneling, trim, or craft application.

Not suitable for professional use.

Warning Read this manual and general safety instructions carefully before

using the appliance, for your own safety.

2 DESCRIPTION (FIG. A)

1. Trigger exhaust vent

2. ¼” coupler

3. Magazine lock

4. Magazine

5. Nailer nose

6. Grease shaft lock

7. Trigger

8. Depth adjustment knob

3 PACKAGE CONTENT LIST

▪ Remove all packaging materials.

▪ Remove remaining packaging and packing inserts (if included).

▪ Check that the package contents are complete.

▪ Check the appliance, the power cord, the power plug and all accessories for

transportation damage.

▪ Keep the packaging materials as far as possible until the end of the warranty period.

Then take it to your local waste disposal system.

WARNING Packaging materials are not toys! Children must not play with

plastic bags! There is a danger of suffocation!

1 x 2 in 1 combi nailer

2 x keys

500 x 25mm nails

500 x 50mm nails

500 x 40mm staples

500 x 25mm staples

1 x empty bottle

1 x BMC

1 x Manual

If any parts are missing or damaged, please contact your dealer.

POWAIR0312 EN

4 SYMBOLS

In this manual and/or on the machine the following symbols are used:

Denotes risk of personal

injury or damage to the

tool.

Read manual before use.

In accordance with

essential safety

standards of applicable

European directives.

Class II - The machine is

double insulated; Earthing

wire is therefore not

necessary.

Mandatory use of eye

protection.

Wear gloves.

Important information.

Electrical products must

not be disposed with the

domestic waste.

5 GENERAL POWER TOOL SAFETY WARNINGS

Read all safety warnings and instructions. Failure to heed warnings and follow instructions

may result in electric shock, fire and/or serious injury. Keep safety warnings and instructions

for future reference. The term "power tool" in the safety warnings refers to your mains-

operated (corded) power tool or battery-operated (cordless) power tool.

5.1 Working area

▪ Keep working area clean and well lit. Untidy and dark areas can lead to accidents.

▪ Do not operate power tools in potentially explosive surroundings, for example, in the

presence of inflammable liquids, gases or dust. Power tools create sparks which may

ignite the dust or fumes.

▪ Keep children and bystanders at a distance when operating a power tool.

Distractions can cause you to lose control of it.

5.2 Electrical safety

Always check that the power supply corresponds to the voltage on the

rating plate.

▪ Power tool plugs must match the outlet. Never modify the plug in any way. Do not

use adapter plugs with earthed power tools. Unmodified plugs and matching outlets

will reduce the risk of a lethal electric shock.

▪ Avoid body contact with earthed surfaces such as pipes, radiators, kitchen ranges

and refrigerators. There is an increased risk of a lethal electric shock if your body is

earthed.

POWAIR0312 EN

▪ Do not expose power tools to rain or wet conditions. If water gets inside a power tool,

it will increase the risk of a lethal electric shock.

▪ Do not damage the cord. Never use the cord for carrying, pulling or unplugging the

power tool. Keep the cord away from heat, oil, sharp edges or moving parts.

Damaged or entangled cords increase the risk of a lethal electric shock.

▪ When operating a power tool outdoors, use an extension cable suitable for outdoor

use. Using a cord suitable for outdoor use reduces the risk of a lethal electric shock.

▪ If operating a power tool in a damp location is unavoidable, use a power supply

protected by a residual current device (RCD). Using an RCD reduces the risk of a

lethal electric shock.

5.3 Personal safety

▪ Stay alert, watch what you are doing and use common sense when operating a

power tool. Do not use a power tool when you are tired or under the influence of

drugs, alcohol or medication. A moment of inattention when operating a power tool

may result in serious personal injury.

▪ Use safety equipment. Always wear eye protection. Using safety equipment such as

a dust mask, non-skid safety shoes, a hard hat, or hearing protection whenever it is

needed will reduce the risk of personal injury.

▪ Avoid accidental starts. Ensure the switch is in the off position before inserting the

plug. Carrying power tools with your finger on the switch or plugging in power tools

when the switch is in the on position makes accidents more likely.

▪ Remove any adjusting keys or spanners before turning on the power tool. A spanner

or key left attached to a rotating part of the power tool may result in personal injury.

▪ Do not reach out too far. Keep your feet firmly on the ground at all times. This will

enable you retain control over the power tool in unexpected situations.

▪ Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and

gloves away from the power tool. Loose clothes, jewellery or long hair can become

entangled in the moving parts.

▪ If there are devices for connecting dust extraction and collection facilities, please

ensure that they are attached and used correctly. Using such devices can reduce

dust-related hazards.

5.4 Power tool use and care

▪ Do not expect the power tool to do more than it can. Use the correct power tool for

what you want to do. A power tool will achieve better results and be safer if used in

the context for which it was designed.

▪ Do not use the power tool if the switch cannot turn it on and off. A power tool with a

broken switch is dangerous and must be repaired.

▪ Disconnect the plug from the power source before making adjustments, changing

accessories, or storing power tools. Such preventive safety measures reduce the risk

of starting the power tool accidentally.

▪ Store power tools, when not in use, out of the reach of children and do not allow

people who are not familiar with the power tool or these instructions to operate it.

Power tools are potentially dangerous in the hands of untrained users.

▪ Maintenance. Check for misalignment or jammed moving parts, breakages or any

other feature that might affect the operation of the power tool. If it is damaged, the

power tool must be repaired. Many accidents are caused by using poorly maintained

power tools.

POWAIR0312 EN

▪ Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp

cutting edges are less likely to jam and are easier to control.

▪ Use the power tool, accessories and cutting tools, etc., in accordance with these

instructions and in the manner intended for the particular type of power tool, taking

into account the working conditions and the work which needs to be done. Using a

power tool in ways for which it was not intended can lead to potentially hazardous

situations.

5.5 Service

▪ Your power tool should be serviced by a qualified specialist using only standard

spare parts. This will ensure that it meets the required safety standards.

6 SPECIAL SAFETY INSTRUCTIONS FOR ELECTRIC STAPLERS

▪ Before inserting staples or nails the power plug should always be removed from the

socket.

▪ Never point the machine at persons or animals.

▪ Only use staples or nails which are suitable for the machine.

▪ Before using the machine, ensure that the safety device is operating properly.

▪ Never block the safety device.

▪ Switch the machine off when you take a break and when the work is completed.

▪ Wear ear protectors.

▪ Do not activate the tool unless the tool is placed firmly against the workpiece. If the

tool is not in contact with the workpiece, the fastener may be deflected away from

your target.

▪ Do not use the tacker for fastening electrical cables. It is not designed for electric

cable installation and may damage the insulation of electric cables thereby causing

electric shock or fire hazard.

7 SAFETY RULES (FIG. B)

▪ Use only following fixing devices:

− Ga. 18 nail & staple

− Nails length: 15-50mm

− Staple crown: 5.7mm

− Staple length: 16-40mm

▪ Tools with an inverted triangle can only be used with security elements: this

stapler/nailer is equipped with a safety yoke.

▪ To prevent injuries to yourself and bystanders, refer to tool use, maintenance and

troubleshooting sections for additional information (fig 1)

▪ To prevent eye injuries, always wear safety glasses with hard plastic side shields. Be

sure everyone in your work area is wearing the same type of safety glasses (fig 2)

▪ Always wear hearing protection and hard hat. (fig 3)

▪ Never use hydrogen oxygen, carbon dioxide or any other bottled gas as a power

source for this tool, the tool will explode and cause serious injury. (fig4)

▪ Remove finger from trigger when not driving fasteners. Never carry tool with finger on

trigger, tool will eject fastener If safety is bumped. (fig5)

▪ Never conned tool to an air hose with pressure exceeds 200 psi or 13.7 BAR (fig6)

▪ Air compressors must comply with requirement ANSI B19.3 1981 (U.S.), "Safety

Standard For Compressors For Process Industries." (fig 7)

POWAIR0312 EN

▪ Air hose minimum working pressure rating of 150 psi (10.3 BAR) or 150% of the

maximum pressure produced in the system is absolutely necessary. (fig 8)

▪ The tool and air supply hose must have a hose coupling such that all pressure is

removed from the tool when the coupling Joint is disconnected. (fig 9)

▪ Use only compressed air coming through 3 pieces set. (fig 10)

▪ Never load fastener before tool connected to air supply (fig 11)

▪ Never use tool if safety element, trigger or springs have become inoperative, missing or

damaged, It is hazardous to remove safety element, trigger or spring. (fig 12)

▪ Before using this tool, make sure trigger, screw and cap are securely tightened. (fig 13)

▪ Do not modify tool without authorization. (fig 14)

▪ Disconnect tool from air whenever the tool stops working (fig15)

▪ Keep the tool pointed away from yourself and others. (fig 16)

▪ Fire fasteners into work surface only, never into materials too hard to penetrate. (fig 17)

▪ Do not drive fasteners on top of other fasteners. Tool fired in an inclined angle is also

forbidden. (fig 18)

▪ Do not push safety element on work surface until a second fastener is desired (fig 19)

▪ Do not drive fasteners close to the edge of the work surface. The work piece is likely to

split and the fastener could fly free and hit someone. (fig 20)

▪ Do not load fasteners with trigger or safety element depressed. (fig 21)

▪ Do not use tool without Danger label on tool. (fig 22)

▪ Never use a tool that leaks air or needs repair. (fig 23)

▪ Be sure you are in a balanced position when using or handling the tool (fig 24)

▪ Operate tool at recommended pressure of 4-8 bar

8 TOOL USE

1. Read "Safety Warnings" before using tool

2. Push magazine lock lever and slide upper magazine to

open magazine.

3. Place strip of nails or staples into the magazine with

the point resting on the fastener guide. Do not load

with trigger depressed.

4. Push upper magazine back until magazine lock

latches.

POWAIR0312 EN

5. Keep the nailer pointed away from yourself and others

and connect to the hose.

6. Position the nailer nose against work piece and pull the

trigger

7. Disconnect air supply in case a nail or stapler is

jammed

8. Pull the grease shaft and pull the upper part of the

nailer nose open the magazine in the front. Remove

jammed nails or staples and close the front cover.

9. Keep the tool pointed away from yourself and others

and connect back to the hose.

9 LUBRICATION

An automatic in-line filter-regulator-lubricator is recommended (Fig 1) as it increases tool life

and keeps the tool in sustained operation. The in-line lubricator should be regularly checked

and filled with air tool oil.

Proper adjustment of the in-line lubricator is performed by placing a sheet of paper next to

the exhaust ports and holding the throttle open approximately 30 seconds. The lubricator is

properly set when a light stain of oil collects on the paper. Excessive amounts of oil should

be avoided.

In the event that it becomes necessary to store the tool for an extended period of time

(overnight, weekend, etc.), it should receive a generous amount of lubrication at that time.

The tool should be run for approximately 30 seconds to ensure oil has been evenly

distributed throughout the tool. The tool should be stored in a clean and dry environment.

▪ It is most important that the tool be properly lubricated by keeping the air line lubricator

filled and correctly adjusted. Without proper lubrication the tool will not work properly

and parts will wear prematurely.

POWAIR0312 EN

▪ Use the proper lubricant in the air line lubricator. The lubricator should be of low air flow

or changing air flow type, and should be kept filled to the correct level. Use only

recommended lubricants, specially made for pneumatic applications. Substitutes may

harm the rubber compounds in the tools, O-rings and other rubber parts.

9.1 Depth adjustment (fig. 1)

The depth to which a fastener is driven is controlled by the depth adjustment knob (8). The

depth of drive is factory adjusted to a nominal setting. Test fire a fastener and check depth.

If a change is desired, rotate the adjustment knob (8). Rotate the knob (8) clockwise to

increase the depth of drive, rotate the knob counter clockwise to decrease the depth of drive.

Test fire another fastener and check depth again. Repeat as necessary to achieve desired

results. The amount of air pressure required will vary depending on the size of the setting to

determine the lowest setting that will consistently perform the job at hand. Air pressure in

excess of that required can cause premature wear and/or damage to the tool.

IMPORTANT!

If no filter/ pressure regulator/ lubricator is installed in the compressed air system, then

pneumatic tools must be lubricated with 2 to 6 drops of oil at least once a day or after every

two hours of use. This must be done directly along the male coupler or the screw (OIL)

provided for the purpose on the side of the tool’s housing.

Fig. 2

1. Tool

1. Quick connector

2. Quick coupler

3. Air hose

4. Quick connector

5. Quick coupler

6. Lubricator

7. Regulator (0-8.3 bar)

8. Filter

9. Cut-off valve

10. Air compressor

10 MAINTENANCE

Disconnect the tool from the compressor before adjusting, clearing jams,

servicing &maintenance, relocating and during non operation.

▪ Regular lubrication, if your tool without using the in-liner automatic oilier, place 2 or 6

drops of pneumatic tool oil into the air inlet before each work day or after 2 hours of

continuous use depending in the characteristic of work piece or type of fasteners.

▪ Air-operated tools must be inspected periodically, and worn or broken parts must be

replaced to keep the tool operating safely and efficiently. Check and change all worn or

damaged O-ring, Seals, etc. Tight all the screws and caps in case personal injury.

▪ Make regular inspection for free movement of trigger, Spring and safety mechanism to

assure safe system is complete and functional: no loose and missing parts, no building

or stocking parts.

▪ Keep magazine and nose of tool clean and free of any dirt lint or abrasive particles.

▪ When temperatures are below freezing, tools should be kept warm by any convenient,

safe method.

POWAIR0312 EN

11 TECHNICAL DATA

Model

POWAIR0312

Activation mode

Single sequential action

Max. allowable pressure

120PSI(8.3 bar)

Operating pressure

60-100PSI(4-7bar)

Air inlet size

¼”

Avg. air consumption

51 l/min

Recommended lubricant

White mineral oil

Nail capacity

100pcs

12 NOISE

Noise emission values measured according to relevant standard. (K=3)

Acoustic pressure level LpA

87 dB(A)

Acoustic power level LwA

100 dB(A)

ATTENTION! Wear hearing protection when sound pressure is over 85

dB(A).

aw (Vibration)

1.9 m/s²

K = 0.8 m/s²

13 TROUBLESHOOTING

SYMPTOM

PROBLEM

SOLUTIONS

Air leak

near top of tool or in

trigger area

O-ring in trigger valve is

damaged.

Check and replace O-ring.

Trigger valve head are

damage.

Check and replace.

Trigger valve stem, seal or

O-ring are damaged.

Check and replace trigger

valve stem, seal or O-ring

Air leak near bottom

of tool.

Loose screws.

Tighten screws.

Worn or damaged O-rings

or bumper.

Check and replace O-rings

or bumper.

Air leak between body

and cylinder cap.

Loose screws.

Tighten screw.

Worn or damaged O-rings

or seals.

Check and replace O-rings

or bumper.

Blade driving fastener

too deep.

Worn bumper.

Replace bumper.

Air pressure is too high.

Adjust the air pressure.

Tool does not operate

well: can not drive

fastener or operate

sluggishly.

Inadequate air supply.

Verify adequate air supply.

Inadequate lubrication.

Place 2 or 6 drops of oil

into air inlet.

Worn or damaged O-rings

or seals.

Check and replace O-rings

or seal.

POWAIR0312 EN

Exhaust port in cylinder

head is blocked.

Replace damaged internal

parts.

Tool skips fasteners.

Worn bumper or damaged

spring.

Replace bumper or pusher

spring.

Dirt in front plate.

Clean drive channel on

front plate.

Dirt or damage prevents

fasteners from moving

freely in magazine.

Magazine needs to be

cleaned.

Worn or dry O-ring on

piston or lack of

Lubrication.

O-ring needs to be

replaced and lubricate.

Cylinder covers seal

leaking.

Replace Sealing washer.

Tool jams.

Incorrect or damaged

fasteners.

Change and use correct

fastener.

Damaged or worn driver

guide.

Check and replace the

driver.

Magazine or nose screw

loose.

Tighten the magazine.

Magazine is dirty.

Clean the magazine.

14 WARRANTY

▪ This product is warranted as provided by law for a 36 -month period effective from

the date of purchase by the first user.

▪ This warranty covers all material or production flaws excluding : batteries, chargers,

defective parts subject to normal wear & tear such as bearings, brushes, cables, and

plugs, or accessories such as drills, drill bits, saw blades, etc. ; damage or defects

resulting from maltreatment, accidents or alterations; nor the cost of transportation.

▪ Damage and/or defects resulting from inappropriate use also do not fall under the

warranty provisions.

▪ We also disclaim all liability for any bodily injury resulting from inappropriate use of

the tool.

▪ Repairs may only be carried out by an authorised customer service centre for

Powerplus tools.

▪ You can always obtain more information at the number 00 32 3 292 92 90.

▪ Any transportation costs shall always be borne by the customer, unless agreed

otherwise in writing.

▪ At the same time, no claim can be made on the warranty if the damage of the device

is the result of negligent maintenance or overload.

▪ Definitely excluded from the warranty is damage resulting from fluid permeation,

excessive dust penetration, intentional damage (on purpose or by gross

carelessness), inappropriate usage (use for purposes for which the device is not

suitable), incompetent usage (e.g. not following the instructions given in the manual),

inexpert assembly, lightning strike, erroneous net voltage. This list is not exhaustive.

POWAIR0312 EN

▪ Acceptance of claims under warranty can never lead to the prolongation of the

warranty period nor commencement of a new warranty period in case of a device

replacement.

▪ Devices or parts which are replaced under the warranty therefore remain the

property of Varo NV.

▪ We reserve the right to reject a claim whenever the purchase cannot be verified or

when it is clear that the product has not been properly maintained. (Clean ventilation

slots, carbon brushes serviced regularly, etc.).

▪ Your purchase receipt must be kept as proof of date of purchase.

▪ Your appliance must be returned undismantled to your dealer in an acceptably clean

state, (in its original blow-moulded case if applicable to the unit), accompanied by

proof of purchase.

15 ENVIRONMENT

Should your appliance need replacement after extended use, do not

dispose of it with the household refuse, but in an environmentally safe way.

Please dispose of used motor oil in a manner that protects the environment.

We suggest you take it in a sealed container to your local service station

for recycling. Do not throw it into the refuse or pour it on the ground

POWAIR0312 EN

16 DECLARATION OF CONFORMITY

VARO – Vic. Van Rompuy N.V. - Joseph Van Instraat 9 - BE2500 Lier - BELGIUM,

declares that,

product: Pneumatic 2 in 1 combi nailer

trade mark: PowerPlus

model: POWAIR0312

is in conformity with the essential requirements and other relevant provisions of the

applicable European Directives, based on the application of European harmonized

standards. Any unauthorized modification of the apparatus voids this declaration.

European Directives (including, if applicable, their amendments up to the date of signature);

2006/42/EC

European harmonized standards (including, if applicable, their amendments up to the date

of signature);

EN ISO1148-13 : 2018

Keeper of the Technical Documentation : Philippe Vankerkhove, VARO – Vic. Van Rompuy

N.V.

The undersigned acts on behalf of the company CEO,

Ludo Mertens

Regulatory Affairs – Compliance Manager

10/02/2022, Lier - Belgium

Powerplus POWAIR0312 Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Andere handleiding(en) van Powerplus POWAIR0312

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info