Handleiding Powerplus POWAIR0310 (pagina 3 van 8) (Engels)

582112

Verklein

Vergroot

Pagina terug

1/8

Pagina verder

POWAIR0310 EN

1 APPLICATION .................................................................................................2

2 DESCRIPTION .................................................................................................2

3 PACKAGE CONTENT LIST ............................................................................2

4 SAFETY RULES ..............................................................................................2

5 ADDITIONAL INSTRUCTIONS FOR FASTENER DRIVING TOOLS

OPERATED BY COMPRESSED AIR ..............................................................3

6 TOOL USE .......................................................................................................4

7 LUBRICATION ................................................................................................5

8 IMPORTANT!!! ................................................................................................5

9 MAINTENANCE ...............................................................................................6

10 TECHNICAL DATA .........................................................................................6

11 NOISE ..............................................................................................................6

12 TROUBLESHOOTING .....................................................................................7

13 ENVIRONMENT ...............................................................................................8

14 DECLARATION OF CONFORMITY ................................................................8

POWAIR0310 EN

PNEUMATIC 2-IN-1 COMBI NAILER

POWAIR0310

1 APPLICATION

Use for almost any finish, furniture, cabinetry, panelling, trim, or craft application.

Warning! For your own safety, read this manual and general safety

instructions carefully before using the appliance.

2 DESCRIPTION

1. Trigger exhaust vent

2. ¼” coupler

3. Magazine lock

4. Magazine

5. Nailer nose

6. Grease shaft lock

7. Trigger

3 PACKAGE CONTENT LIST

 Remove all packaging materials.

 Remove remaining packing and package inserts (if included).

 Check that the package contents are complete.

 Check the appliance, the power cord, the power plug and all accessories for

transportation damage.

 Keep the packing materials as long as possible till the end of the warranty period.

Dispose it into your local waste disposal system afterwards.

WARNING: Packaging materials are not toys! Children must not play with

plastic bags! Danger of suffocation!

1 x 2-in-1 combi nailer

2 x keys

500 x 20 mm nails

500 x 32 mm nails

500 x 25 mm staples

500 x 16 mm staples

1 x BMC

1 x manual

If any parts are missing or damaged, please contact your dealer.

4 SAFETY RULES

 Use only following fixing devices:

 Ga. 18 nail & staple

 Nails length: 15-32mm

 Staple crown: 5.7mm

 Staple length: 16-32mm

 Tools with an inverted triangle can only be used with security elements: this

stapler/nailer is equipped with a safety yoke.

POWAIR0310 EN

 Repairs can only be effected by official dealers.

 To prevent injuries to yourself and bystanders, refer to tool use, maintenance and

troubleshooting sections for additional information (fig. 1).

 To prevent eye injuries, always wear safety glasses with hard plastic side shields.

Be sure everyone in your work area is wearing the same type of safety glasses (fig.

2).

 Always wear hearing protection and a hard hat (fig. 3).

 Never use hydrogen, oxygen, carbon dioxide or any other bottled gas as a power

source for this tool, the tool will explode and cause serious injury (fig. 4).

 Remove your finger from trigger when not driving fasteners. Never carry the tool with

finger on the trigger, the tool will eject a fastener when the safety is pressed (fig. 5).

 Never connect the tool to an air hose with pressure exceeding 200 psi or 13.7 bar

(fig. 6).

 Air compressors must comply with requirement ANSI B19.3 1981 (U.S.), "Safety

Standard for Compressors for Process Industries" (fig. 7).

 Air hose minimum working pressure rating of 150 psi (10.3 bar) or 150% of the

maximum pressure produced in the system is absolutely necessary (fig. 8).

 The tool and air supply hose must have a hose coupling such that all pressure is

removed from the tool when the coupling joint is disconnected (fig. 9).

 Use only compressed air coming through 3 pieces set (fig. 10).

 Never load the tool if it is connected to air supply (fig. 11).

 Never use the tool if the safety element, trigger or springs have become inoperative,

missing or damaged. It is hazardous to remove the safety element, trigger or spring

(fig. 12).

 Before using this tool, make sure trigger, screw and cap are securely tightened (fig.

13).

 Do not modify tool without authorization (fig. 14).

 Disconnect the tool from the air supply whenever the tool stops working (fig.15).

 Keep the tool pointed away from yourself and others (fig. 16).

 Fire fasteners into work surface only, never into materials too hard to penetrate (fig.

17).

 Do not drive fasteners on top of other fasteners. Firing the tool in an inclined angle is

also forbidden (fig. 18).

 Do not push safety element on work surface until a second fastener is desired (fig.

19).

 Do not drive fasteners close to the edge of the work surface. The work piece is likely

to split and the fastener could fly free and hit someone (fig. 20).

 Do not load fasteners with trigger or safety element depressed (fig. 21).

 Do not use tool without Danger-label on tool (fig. 22).

 Never use a tool that leaks air or needs repair (fig. 23).

 Be sure you are in a balanced position when using or handling the tool (fig. 24).

 Operate the tool at recommended pressure of 4-8 bar.

5 ADDITIONAL INSTRUCTIONS FOR FASTENER DRIVING TOOLS OPERATED BY

COMPRESSED AIR

 fastener driving tools operated by compressed air shall only be connected to

compressed air lines where the maximum allowable pressure cannot be exceeded

by a factor of more than 10%, which can for example be achieved by a pressure

reduction valve which includes a downstream safety valve;

POWAIR0310 EN

 when using fastener driving tools operated by compressed air, particular attention

must be paid to avoid exceeding the maximum allowable pressure;

 fastener driving tools operated by compressed air should only be operated at the

lowest pressure required for the work process at hand, in order to prevent

unnecessarily high noise levels, increased wear and resulting failures;

 hazards caused by fire and explosion when using oxygen or combustible gases for

operating compressed air operated fastener driving tools.

6 TOOL USE

1. Read "Safety Warnings" before using the tool.

2. Push magazine lock lever and slide upper magazine to

open magazine.

3. Place strip of nails or staples into the magazine with the

point resting on the fastener guide. Do not load with

trigger depressed.

4. Push upper magazine back until magazine lock latches.

5. Keep the nailer pointed away from yourself and others

and connect to the hose.

6. Position the nailer nose against work piece and pull the

trigger.

POWAIR0310 EN

7. Disconnect air supply in case a nail or stapler is jammed.

8. Pull the grease shaft and pull the upper part of the nailer

nose open the magazine in the front. Remove jammed

nails or staples and close the front cover.

9. Keep the tool pointed away from yourself and others and

connect back to the hose.

7 LUBRICATION

An automatic in-line filter-regulator-lubricator is recommended (Fig 1) as it increases tool

life and keeps the tool in sustained operation. The in-line lubricator should be regularly

checked and filled with air tool oil.

Proper adjustment of the in-line lubricator is performed by placing a sheet of paper next to

the exhaust ports and holding the throttle open approximately 30 seconds. The lubricator

is properly set when a light stain of oil collects on the paper. Excessive amounts of oil

should be avoided.

In the event that it becomes necessary to store the tool for an extended period of time

(overnight, weekend, etc.), it should receive a generous amount of lubrication at that time.

The tool should be run for approximately 30 seconds to ensure oil has been evenly

distributed throughout the tool. The tool should be stored in a clean and dry environment.

 It is most important that the tool be properly lubricated by keeping the air line lubricator

filled and correctly adjusted. Without proper lubrication the tool will not work properly

and parts will wear prematurely.

 Use the proper lubricant in the air line lubricator. The lubricator should be of low air flow

or changing air flow type, and should be kept filled to the correct level. Use only

recommended lubricants, specially made for pneumatic applications. Substitutes may

harm the rubber compounds in the tools, O-rings and other rubber parts.

8 IMPORTANT!!!

If no filter/ pressure regulator/ lubricator is installed in the compressed air system, then

pneumatic tools must be lubricated with 2 to 6 drops of oil at least once a day or after

every two hours of use. This must be done directly along the male coupler or the screw

(OIL) provided for the purpose on the side of the tool’s housing.

Automatic lubrication is also possible using the supplied mini oiler that you have to install

between the threaded connector of the tool and the male coupler. Make sure that the oiler

is always filled with suitable oil.

POWAIR0310 EN

Fig. 1

1. Tool

2. Quick connector

3. Quick coupler

4. Air hose

5. Quick connector

6. Quick coupler

7. Lubricator

8. Regulator (0-8.5 bar)

9. Filter

10. Cut-off valve

11. Air compressor

9 MAINTENANCE

Disconnect the tool from the compressor before adjusting, clearing jams,

servicing & maintenance, relocating and during non operation.

 Regular lubrication. If you use your tool without using the in-liner automatic oilier,

place 2 or 6 drops of pneumatic tool oil into the air inlet before each work day or

after 2 hours of continuous use depending in the characteristic of work piece or type

of fasteners.

 Air-operated tools must be inspected periodically, and worn or broken parts must be

replaced to keep the tool operating safely and efficiently. Check and change all worn

or damaged O-ring, Seals, etc. Tight all the screws and caps to prevent personal

injury.

 Make regular inspection for free movement of trigger, spring and safety mechanism

to assure safe system is complete and functional: no loose and missing parts, no

building up of dirt and no jammed fasteners.

 Keep magazine and nose of tool clean and free of any dirt lint or abrasive particles.

 When temperatures are below freezing, tools should be kept warm by any

convenient, safe method.

10 TECHNICAL DATA

Model

POWAIR0310

Activation mode

Single sequential action

Max. allowable pressure

120 PSI (8.3 bar)

Air inlet size

¼”

Avg. air consumption

78.68 l/min (2.78 cfm)

Recommended lubricant

White mineral oil

Nail capacity

100 pcs

11 NOISE

Noise emission values measured according to relevant standard. (K=3)

Acoustic pressure level LpA

88 dB(A)

Acoustic power level LwA

101 dB(A)

ATTENTION! Wear hearing protection when sound pressure is over 85

dB(A).

POWAIR0310 EN

aw (Vibration)

4.6 m/s²

K = 0.02 m/s²

12 TROUBLESHOOTING

SYMPTOM

PROBLEM

SOLUTIONS

Air leak

near top of tool or in

trigger area

O-ring in trigger valve is

damaged.

Check and replace O-ring.

Trigger valve head are

damage.

Check and replace.

Trigger valve stem, seal or

O-ring are damaged.

Check and replace trigger

valve stem, seal or O-ring

Air leak near bottom of

tool.

Loose screws.

Tighten screws.

Worn or damaged O-rings or

bumper.

Check and replace O-rings

or bumper.

Air leak between body

and cylinder cap.

Loose screws.

Tighten screw.

Worn or damaged O-rings or

seals.

Check and replace O-rings

or bumper.

Blade driving fastener

too deep.

Worn bumper.

Replace bumper.

Air pressure is too high.

Adjust the air pressure.

Tool does not operate

well: can not drive

fastener or operate

sluggishly.

Inadequate air supply.

Verify adequate air supply.

Inadequate lubrication.

Place 2 or 6 drops of oil into

air inlet.

Worn or damaged O-rings or

seals.

Check and replace O-rings

or seal.

Exhaust port in cylinder head

is blocked.

Replace damaged internal

parts.

Tool skips fasteners.

Worn bumper or damaged

spring.

Replace bumper or pusher

spring.

Dirt in front plate.

Clean drive channel on front

plate.

Dirt or damage prevents

fasteners from moving freely

in magazine.

Magazine needs to be

cleaned.

Worn or dry O-ring on piston

or lack of Lubrication.

O-ring needs to be replaced

and lubricate.

Cylinder covers seal leaking.

Replace Sealing washer.

Tool jams.

Incorrect or damaged

fasteners.

Change and use correct

fastener.

Damaged or worn driver

guide.

Check and replace the

driver.

Magazine or nose screw

loose.

Tighten the magazine.

POWAIR0310 EN

Magazine is dirty.

Clean the magazine.

13 ENVIRONMENT

Should your appliance need replacement after extended use, do not dispose of it with the

household refuse, but in an environmentally safe way.

14 DECLARATION OF CONFORMITY

VARO N.V. - Joseph Van Instraat 9 - BE2500 Lier - BELGIUM, declares that,

product: Pneumatic 2-in-1 combi nailer

trade mark: POWERplus

model: POWAIR0310

is in conformity with the essential requirements and other relevant provisions of the

applicable European Directives, based on the application of European harmonized

standards. Any unauthorized modification of the apparatus voids this declaration.

European Directives (including, if applicable, their amendments up to the date of

signature);

2006/42/EC

European harmonized standards (including, if applicable, their amendments up to the date

of signature);

EN792-13: 2000

Keeper of the Technical Documentation : Philippe Vankerkhove, VARO – Vic. Van

Rompuy N.V.

The undersigned acts on behalf of the company CEO,

Hugo Cuypers

Certification Manager

Date: 18/02/15

Powerplus POWAIR0310 Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Andere handleiding(en) van Powerplus POWAIR0310

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info