480905
7
Verklein
Vergroot
Pagina terug
1/14
Pagina verder
POW64256 EN
Copyright © 2015 VARO P a g e | 7 www.varo.com
Before commencing work, always check that the chainsaw works properly and is safe to
operate.
Check also that the chain lubrication and the oil gauge are in good working order (see
Fig.4). When the oil lever is approx. 5 mm from the bottom mark, you must top up with oil.
When the oil level is higher you can work without worry.
Switch on the chain saw and hold it above the ground. Be careful not allow the chainsaw
to touch the ground. For safety reasons it is best to keep a clearance of at least 20 cm. If
you now see growing traces of oil, the chain lubrication system is working correctly. If
there are no traces of oil at all, try cleaning the oil outlet (Fig 2, C), the upper chain
tensioning borehole (E) and the oil duct, or contact your Customer Service. (Be sure to
read the section “Filling in chain oil and chain lubrication” on this point).
Check the chain tension and retention, if necessary (see the section “Tensioning the saw
chain” on this point).
Make sure the chain brake is working properly (see also the section “Releasing the chain
brake”).
9 ASSEMBLY
9.1 Fitting the guide bar and chain (Fig 1, 2, 3)
If the chain saw is already connected to the power supply: Pull the plug
from the socket outlet. Wear protective gloves whenever doing any work on
the saw chain.
Important: The front finger guard (3) must always be in the top (vertical) position (Fig. 5).
The guide bar and saw chain are supplied separately. To assemble, first unscrew the lock nut
(5) and remove the guide bar cover (6). The guide bolt (17) must be in the centre of the guide.
If necessary, adjust the chain tensioning with the chain wheel (16).
To prevent injury on the sharp cutting edges, always wear gloves when
assembling, tensioning and checking the chain.
Before assembling the guide bar with the saw chain, check the cutting direction of the teeth!
The running direction is marked with an arrow on the cover (6) (Fig 3, G). To determine the
direction of cut, it may be necessary to turn over the saw chain (4). Hold the guide bar (7)
vertically with the tip pointing upwards and put on the saw chain (4, beginning at the tip of the
bar.
Then assemble the guide bar with the saw chain as follows:
Place the guide bar with the saw chain on the chain wheel (16) and guide bolt (17).
Place the saw chain round the chain wheel (16) and make sure it is correctly mounted (see
Fig.1, A).
Place the cover (6) on top and tighten gently with the lock nut (5). Now the saw chain has
to be correctly tensioned.
9.2 Tensioning the saw chain
Always pull the plug out of the power socket before doing any work on the
chainsaw!
Wear safety gloves!
Make sure the saw chain (4) is inside the guide groove of the guide bar (7) (Fig.1 a)!
7

Hulp nodig? Stel uw vraag in het forum

Spelregels
1

Forum

Powerplus-POW64256

Zoeken resetten

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Powerplus POW64256 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Powerplus POW64256 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,36 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Powerplus POW64256

Powerplus POW64256 Gebruiksaanwijzing - Nederlands - 15 pagina's

Powerplus POW64256 Gebruiksaanwijzing - Deutsch - 15 pagina's

Powerplus POW64256 Gebruiksaanwijzing - Français - 15 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info