685372
37
Verklein
Vergroot
Pagina terug
1/56
Pagina verder
GENERATOR ENCLOSURES
Some installations require the Genset to be mounted inside an enclosure. Enclosures are
generally constructed of heavy gauge sheet metal, and completely insulated. Enclosures are
typically installed in RV’s with large unobstructed compartments. The major advantage to
installing a Genset in an enclosure is to achieve a significant reduction in the unit’s sound level.
In order to maintain the ambient temperature within the enclosure a forced cool air
system is generally employed. Two blower fans capable of producing a minimum of 465 CFM
each should be mounted at the generator end of the enclosure. Cooling air circulates around the
generator end and engine, forcing excess heat to exit through an air duct outlet to the outside air.
Since hot air will rise the air duct outlet opening should be located near the inside top surface of
the enclosure, the opening should be approximately 25 square inches.
Openings in the base of the enclosure and compartment floor are required for the engine
exhaust pipe, oil drain hose and engine breather hose. Other holes for fuel lines, electrical leads,
remote radiator hoses, etc. are usually located in the rear wall of the enclosure. Be sure to seal
around these items to prevent fumes or vapors from entering the vehicles compartment. Two
hinged doors at the front of the enclosure enable unobstructed access to the engine and control
box for routine maintenance. A removable service panel in the rear wall of the enclosure
facilitates servicing the back side of the Genset.
The clearance between the enclosure and the vehicles compartment walls is another
consideration. Except for the rear wall of the enclosure the clearances at the top, sides and front
can be minimal. A ½” gap per side is enough clearance for easy installation or removal. At the
rear of the enclosure the compartment depth must be large enough to accommodate the two
blower fans and system connections. A minimum of 10” between the enclosure and rear
compartment wall is required for this area. Also, remember a 400 sq. inch free air opening is
required to supply the forced air cooling system. See section on “Air Requirements” for details.
Dimensions and layouts are provided for your planned installation, be sure to follow all
requirements. Power Technology’s Customer Service Department is available to answer any
questions you may have concerning your Genset and installation.
IMPORTANT: When installing a RV generator set the installation must comply with the
current Safety Standards of ANSI / RVIA EGS-1-2003, ANSI A 119.2 / NFPA 501C and
applicable articles of ANSI / NFPA 70 of the National Electrical Code. Generator set
installations must also comply with state and local requirements.
IMPORTANT: An enclosure manufactured by any person (s) other then Power Technology
must follow the requirements set forth in this manual. All specifications must be adhered to;
failure to do so may affect your Power Technology Southeast, Inc. Limited Warranty.
7
37

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw PowerTech PTRV-17.5KT bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van PowerTech PTRV-17.5KT in de taal/talen: Engels als bijlage per email.

De handleiding is 2,37 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info