685330
34
Verklein
Vergroot
Pagina terug
1/44
Pagina verder
SYSTEMS CONNECTION
FUEL SYSTEM
The diesel fuel system for the generator set must be designed to operate independently from the
vehicles main engine if both engines are to be operated at the same time. The best way to do this is to
have separate fuel tanks, but this is usually impractical because of space restrictions. In most
installations both engines operate from a common fuel tank with separate pick-up tubes for each
engine, not a Tee fitting arrangement. This prevents either or both engines from being starved for fuel.
The generator set fuel pick-up tube is generally shorter than the vehicles; therefore fuel may not be
available to the generator when fuel supply is low. This will prevent the generator from depleting the
fuel supply needed by the main engine.
NOTE: Using a simple Tee fitting to supply both engines from a common fuel line is not
recommended. This practice may possible cause a fuel starvation situation to either or both engines.
Also, if excessive pressure were to build up in the main supply line it could possible cause a failure of
the generators fuel lines or connectors and a hazardous fuel leak may occur.
Care must be taken when routing the fuel line from the main tank to the generator set. Keep the
fuel line as short as possible while maintaining adequate clearance from the exhaust system. Fuel lines
must be run along the frame side rails or coach under carriage. Never run fuel lines inside of the coach.
Securely fasten the fuel lines with hardware that is recommended for the type of fuel line used. The
fuel lines should enter the generator compartment at a point nearest to the generators fuel line
connection fittings. Allow for a minimum of 8inches of flexible fuel line to make the connection. Use
proper size fuel line to accommodate the fuel flow needed. Steel fuel line or high quality fuel hose is
recommended, either one should have a minimum of ¼” ID and strong enough to withstand road and
climatic conditions. A positive fuel shut-off valve should be located between the fuel tank and fuel
connection on the generator.
EXHAUST SYSTEM
Exhaust system components installed on a RV Genset must be approved and properly installed to
meet the codes and regulations required by Federal and State agencies. Exhaust Mufflers and Spark
Arrestors supplied by Power Technology meet the codes and standard requirements set forth by the
USDA Forest Service. Laws pertaining to application and maintenance of a Spark Arrestor may vary
depending on your location and State regulations. Federal laws apply on Federal lands. If a generator
is used in a forest, on brush or grass covered unimproved land it must be equipped with a Spark
Arrestor. It is the responsibility of the vehicle owner or operator to install and maintain the entire
exhaust system in good working condition.
CAUTION: Any person (s) who installs an unapproved Muffler, Spark Arrestor or other exhaust
system component, and/or modifies an exhaust system or component that may result in a hazardous
condition is liable for damages, injuries or warranty expense caused by such unapproved installation
and/or modification.
9
34

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw PowerTech PT-10KSI bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van PowerTech PT-10KSI in de taal/talen: Engels als bijlage per email.

De handleiding is 5,62 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info