494400
61
Verklein
Vergroot
Pagina terug
1/75
Pagina verder
Controlling the rest of your system
09
61
En
English Italiano Français
Nederlands
EspañolDeutsch
3 Use the number buttons to enter the
preset code.
You can find the preset codes on page 66
(VSX-D514/D714) and page 68 (VSX-D814).
The LED blinks again after you enter the code.
If the correct code has been input the power
of the component being input will turn on or
off.
The power of the component being input will
only turn on or off if that component is able to
be turned on directly by remote control.
You can only input a code for the compo-
nent type written on each
MULTI
CONTROL
button (except
RECEIVER
and
TUNER
).
Even if you don’t input a preset code for
the TV (
TV/SAT
MULTI CONTROL
button)
you will be able to control your TV using
the dedicated
TV CONTROL
on the
remote if you have assigned it to the
TV
CONT
button.
You may not be able to use a particular
code even if it is listed on page 66.
The remote control buttons will not be
able operate other equipment unless
preset with the method above.
4 Repeat steps 2 through 3 to try a
different code, or to enter a code for
another component you want to control.
5 When you’re done, press RECEIVER.
Programming signals from
other remote controls
VSX-D814 only
If the preset code for your component is not
available, or the available preset codes do not
operate correctly, you can program signals
from the remote control of another compo-
nent (for example
,
, or other operation
buttons). This can also be used to program
additional operations (buttons not covered in
the presets) after assigning a preset code.
1 While pressing the RECEIVER button,
press and hold the 2 button.
The LED blinks.
2 Press the MULTI CONTROL button for
the component you want to control.
The LED lights.
To exit or cancel press
RECEIVER
.
3 Point the two remote controls
towards each other about 2–5 cm apart
then press the button that will be doing
the learning on this receiver’s remote
control.
The LED blinks rapidly.
4 Press the corresponding button on the
other remote control that is sending
(teaching) the signal to this receiver’s
remote control.
If the operation has been learned success-
fully, the LED on this receiver’s remote will
blink once then light steadily.
If for some reason the operation hasn’t been
learned the LED will blink for three seconds
and then light steadily. If this happens, keep
pressing the (teaching) button as you vary the
distance between the two remotes, until you
see the LED light steadily.
If there is not enough memory for this button
to be learned by the remote, the LED will blink
twice and the operation will be canceled.
5 To program additional signals for the
current component repeat steps 3 and 4.
To program operations for another compo-
nent exit and repeat steps 1 through 5.
2 – 5 cm
10_controlling_system.fm 61 ページ 2004年3月3日 水曜日 午後2時2分
61

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Pioneer VSX-D814 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Pioneer VSX-D814 in de taal/talen: Engels als bijlage per email.

De handleiding is 2,47 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info