586461
119
Verklein
Vergroot
Pagina terug
1/137
Pagina verder
119
FAQ
14
MHL
Symptom Remedy
When playing an MHL-compatible
device connected to the MHL termi-
nal, the Standby Through function
does not work and the power turns
off.
The MHL device will not operate unless power is being supplied from this receiver. When
this receiver is in the Standby Through mode, power cannot be supplied due to reduced
power consumption. Because of this, the MHL device will not operate. This is not a mal-
function.
MHL-compatible device cannot be
operated with the remote control.
Press MHL to set the remote control to the MHL control mode.
MHL POW ERR is displayed on the
display.
There is a problem with the power supply for the MHL device. After turning OFF the
receiver, disconnect the MHL device, connect the MHL device again and then turn ON
the power of the receiver.
If the error is displayed even though the above operation is repeated several times,
there is a problem with the receiver or the MHL device. Disconnect the power cable and
request repair.
Built-in AVNavigator
Symptom Cause Remedy
AVNavigator does not inter-
act well with the receiver.
The receiver’s power is not turned
on.
Turn the receiver’s power on. (Wait about 60 seconds after
the power turns on for network functions to start.)
The receiver or computer is not con-
nected to the LAN.
Connect a LAN cable to the receiver or computer (pages
34 , 47 ).
The router’s power is off. Turn the router’s power on.
Network connections could be
restricted due to the computer’s
network settings, security settings,
etc.
Check the computer’s network settings, security settings,
etc.
In the middle of
Wiring Navi, you are
instructed to turn off the
power of the unit and then
connect other equipment or
speakers.
This is to avoid failure of the receiver
due to a short-circuit between
cables or from static electricity.
Per the Wiring Navi instructions, turn OFF the power
of the receiver. As long as the browser has not quit,
Wiring Navi resumes guidance upon turning ON the
receiver.
When the Wiring Navi or
Interactive Operation Guide
(VSX-1130 only) is launched,
a warning about security
protection appears on the
browser.
This is because of the browser’s
security function.
This is not a problem. Perform the operation to authorize
the blocked contents.
AVNavigator screen is not
displayed on the browser.
This receiver’s IP address has not
been entered into the browser
correctly.
Check the receiver’s IP address and enter it correctly in the
browser (page 57 ).
Receiver settings cannot be
made from a browser.
JavaScript is disabled on the inter-
net browser.
Enable JavaScript.
The browser is not compatible with
JavaScript.
Use an internet browser that is compatible with JavaScript.
USB interface
Symptom Cause Remedy
The folders/files stored on a
USB memory device are not
displayed.
The folders/files are currently stored
in a region other than the FAT (File
Allocation Table) region.
Store the folders/files in the FAT region.
The number of levels in a folder is
more than 9.
Limit the maximum number of levels in a folder to 9 (page
65 ).
The audio files are copyrighted.
Copyrighted audio files stored on a USB memory device
cannot be played back (page 65 ).
A USB memory device is
not recognized.
The USB memory device does not
support the mass storage class
specifications.
Try using a USB memory device compatible with the mass
storage class specifications. Note that there are cases
where even the audio files stored on a USB memory device
compatible with the mass storage class specifications are
not played back on this receiver (page 65 ).
Connect the USB memory device and switch on this
receiver (pages 35 , 47 ).
A USB hub is currently being used.
This receiver does not support USB hubs (page 65 ).
This receiver recognizes the USB
memory device as a fraud.
Switch off and on again this receiver.
Reconnect the USB device with the receiver switched off.
Change to an input other than iPod/USB, then set the input
back to iPod/USB.
A USB memory device is
connected and displayed,
but the audio files stored
on the USB memory device
cannot be played back.
Some formats of USB memory
devices, including FAT 12, NTFS, and
HFS, cannot be played back on this
receiver.
Check whether the format of your USB memory device is
either FAT 16 or FAT 32. Note that the FAT 12, NTFS, and
HFS formats cannot be played back on this receiver (page
65 ).
The file format cannot be properly
played back on this receiver.
See the list of file formats that can be played back on this
receiver (page 66 ).
The USB memory cannot be
operated with the remote
control.
Press iPod USB to set the remote control to the iPod USB
control mode.
Over Current shows in the
display.
There is a problem with the power supply for the USB
memory. After turning off the receiver, disconnect the USB
memory, connect the USB memory again and then turn on
the power of the receiver.
If Over Current is displayed even though the above opera-
tion is repeated several times, there is a problem with the
receiver or USB memory. Disconnect the power cable and
request repair.
 
119

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Pioneer VSX-1130 K bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Pioneer VSX-1130 K in de taal/talen: Engels als bijlage per email.

De handleiding is 20,3 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Pioneer VSX-1130 K

Pioneer VSX-1130 K Gebruiksaanwijzing - Nederlands - 146 pagina's

Pioneer VSX-1130 K Gebruiksaanwijzing - Deutsch - 146 pagina's

Pioneer VSX-1130 K Gebruiksaanwijzing - Français - 145 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info