574062
96
Verklein
Vergroot
Pagina terug
1/104
Pagina verder
Additional information
11
96
En
Settings
Remote control
Symptom Cause Remedy
The Auto Surround Setup
continually shows an error.
• The ambient noise level in the room is too
high.
• Keep the noise level in the room as low as possible
when using the Auto Surround Setup. If the noise cannot
be kept low enough, you will have to set up the surround
sound manually (page 51).
After using the Auto Surround
Setup, the subwoofer distance
setting is set further than the
actual measured distance.
• The low-pass filter found in subwoofers can
introduce a delay in the playback sound.
• This is not a malfunction. The Auto Surround Setup has
compensated for the delay caused by the filter.
After using the Auto Surround
Setup, the speaker size setting
(LARGE or SMALL) is incorrect.
• There was some inaudible low-frequency
noise in the room.
• The low-frequency noise could have been caused by an
air conditioner or motor. Switch off all appliances in the
room and rerun the Auto Surround Setup.
Symptom Cause Remedy
The amplifier cannot be remote
controlled.
• You are too far away or at a bad angle for
operation.
• Operate within 7 m, 30° of the remote sensor on the
front panel (see Using the remote control on page 7).
• There is an obstacle between the amplifier
and the remote control.
• Remove the obstacle or operate from another angle of
position.
• Strong light such as fluorescent light. • Avoid exposing the remote sensor on the front panel to
direct light.
• The remote control has a weak charge. • Recharge the remote control (see Recharging the remote
control on page 7). You can also use the remote while it’s
placed on the recharger.
• The remote control is locked. • Unlock the remote control (see Locking the remote
control on page 10).
• The CONTROL IN jack has been hooked up. • Disconnect the CONTROL IN jack (see Operating other
Pioneer components with this unit’s sensor on page 68).
Other components cannot be
remote controlled.
• The proper code hasn't been input into the
remote control to control that component.
• Input the proper code into the remote control (see
page 61).
• Something is plugged into the CONTROL IN
jack.
• Either point remote at the remote sensor of the unit that
is plugged into the CONTROL IN jack or unplug the cable
from the CONTROL IN jack and use remote normally (see
Operating other Pioneer components with this unit’s
sensor on page 68).
The remote control doesn’t seem
to recharge properly (the
recharge indicator doesn’t light),
or it won’t hold a charge.
• The remote control hasn’t been seated
properly on the recharger.
• Reseat it on the recharger, making sure to align the
indent on the bottom of the remote with the tabs on the
recharger.
• The battery cells need to be replaced. • See Replacing the lithium-ion batteries on page 11.
The remote control display is
flashing LOW BATTERY or is
blank.
• The remote control needs to be recharged. • Place the remote control on the recharger. If the remote
hasn’t been charged for awhile, the remote control display
may remain blank for several minutes before the touch
screen appears. See Recharging the remote control on
page 7 for more on this.
The remote control display is
blank or very hard to see.
• The remote control contrast needs to be
adjusted.
• Use the contrast control on the right-hand side of the
remote to adjust the contrast as necessary.
• The remote control backlight is switched on
in a bright room.
• Switch the backlight off.
When you press an input select
button on the Home menu
screen, the amplifier input
source doesn’t change to the
selected function.
• The Direct Function feature for the
component you want to select is switched off.
• See Remote Direct function on page 64 to switch it on
again.
Can’t program certain buttons
with remote signals when using
the learning feature.
• You have selected a button that cannot
learn commands.
• Select another button that can learn commands (see
Programming signals from other remote controls on
page 63).
• You have already selected a button for
learning.
• Press the same button again to deselect it or press END
to go back a screen (see Programming signals from other
remote controls on page 63).
96

Hulp nodig? Stel uw vraag in het forum

Spelregels
1

Forum

Pioneer-VSA-AX10i-S

Zoeken resetten

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Pioneer VSA-AX10i-S bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Pioneer VSA-AX10i-S in de taal/talen: Engels als bijlage per email.

De handleiding is 3,16 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Pioneer VSA-AX10i-S

Pioneer VSA-AX10i-S Gebruiksaanwijzing - Nederlands - 104 pagina's

Pioneer VSA-AX10i-S Gebruiksaanwijzing - Deutsch - 104 pagina's

Pioneer VSA-AX10i-S Gebruiksaanwijzing - English - 25 pagina's

Pioneer VSA-AX10i-S Gebruiksaanwijzing - Français - 104 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info